GoldRushAlaskaS03E12
Wanderlust UK - March 2018

IPitomy IP PBX Administrator Guide

Loading...
IPitomy IP PBX Administrator Guide Version v4.0.1

IPitomy IP PBX Admin Guide

All materials in this documentation are proprietary and considered confidential to IPitomy Communications, LLC and may not be disclosed without the express written permission of Ipitomy Communications, LLC. © 2010 Ipitomy Communications, LLC – All rights reserved.

Ipitomy Communications, LLC Phone: 941.306.2200 Email: [email protected] www.ipitomy.com Corporate Offices: 1940 Northgate Blvd. Suite B-1 Sarasota, FL 34234

Release History Date

Software Version, Document Release #

Description

June 01, 2010

Draft – Rev. 1

New release of documentation to include product upgrade Version v3.1-2458.

June 11, 2010

Draft – Rev 2

Incorporated new features and still updating to match current version v3.1.2458.

June 25, 2010

Draft – Final Version

Draft submitted for technical review.

June 28, 2010

Draft – Final Version

Updated document to include information for ACD table. Update document for general formatting and style consistency.

July 2, 2010

Draft – Final Version

Updated to include new fields for CID, Cascading Messages from 3.1.2595 release notes.

September 23, 2010

3.1-2598

Fully updated to reflect the PBX up to v3.12598

Oct 4, 1020

3.2.2

Updated manual to reflect v3.2.2

February 9, 2011

4.0.1

Updated manual to reflect v4.0.1, v3.4.1 and v3.4.2

IPitomy IP PBX Admin Guide

TABLE OF CONTENT INTRODUCTION.................................................................................................................................... 1 About the IPitomy IP PBX ........................................................................................................................................1 Benefits of VoIP Technology...................................................................................................................................1 IPitomy IP PBX Features ..........................................................................................................................................1 Extensions ..........................................................................................................................................................................................3 Groups ................................................................................................................................................................................................3 Menus (Automated Attendant)...........................................................................................................................................................3 DTMF Menu Administration ...............................................................................................................................................................3 Advanced Routing Functions ............................................................................................................................................................3 Voicemail and Unified Messaging .....................................................................................................................................................3 Directory .............................................................................................................................................................................................3 Direct Inward Dialing (DID) Numbers ................................................................................................................................................3 Conferencing (Meet Me) .....................................................................................................................................................................3 FollowMe.............................................................................................................................................................................................4 Forwarding Gateway ..........................................................................................................................................................................4 Cascading Message Notification .......................................................................................................................................................4 Voicemail Gateway .............................................................................................................................................................................4 Branch Offices....................................................................................................................................................................................4

GETTING STARTED ............................................................................................................................. 5 Boot Up – Safe Power Down....................................................................................................................................5 Connecting the System............................................................................................................................................6 Hardware Setup ......................................................................................................................................................6 Connecting the Phone Lines ...................................................................................................................................6 INTERNAL ANALOG LINE CARDS ................................................................................................................................... 6 Digium 2404B 16 and 2406B 24 Analog Line Cards (16 or 24 PSTN line connections) ............................................... 7

INTERNAL DIGITAL T1 CARDS ............................................................................................................................7 Digium TE122P T1 Card (a single T1/E1/J1 connection) ................................................................................................ 7 Digium TE205P T1 Card (a dual T1/E1/J1 connection) ................................................................................................... 7

Connecting Using an External Gateway .................................................................................................................7 Connecting to a LAN ...............................................................................................................................................8 Connecting Using SIP Providers.............................................................................................................................8 Connecting Telephones ..........................................................................................................................................9

DATA AND NETWORK CONFIGURATION ........................................................................................ 10 Setup Worksheet ....................................................................................................................................................10 CSV Upload ..........................................................................................................................................................12 Network Requirements...........................................................................................................................................13 Port Forwarding ......................................................................................................................................................14 IP Addresses ...........................................................................................................................................................15 Changing the IP Address ......................................................................................................................................15 Service Providers ...................................................................................................................................................16

SYSTEM ADMINISTRATION............................................................................................................... 17 Administration Menu ..............................................................................................................................................17 IP PBX Administration Options .............................................................................................................................17 Administration Page Layout ..................................................................................................................................18 Navigational Tools.................................................................................................................................................19 Login Page ............................................................................................................................................................20

IPitomy IP PBX Admin Guide Logging In .........................................................................................................................................................................20 Logging Out ......................................................................................................................................................................20

SYSTEM NETWORKING..................................................................................................................... 21 TCP/IP Settings Section.........................................................................................................................................22 Edit TCP/IP Default Settings.................................................................................................................................22 Access Control (PBX Access)...............................................................................................................................22 Host Access ..........................................................................................................................................................22 Web Server Configuration .....................................................................................................................................23 Add New Permission.............................................................................................................................................25 Load Factory Default.............................................................................................................................................25 Access Control List ................................................................................................................................................27 Load Recommended Default ................................................................................................................................29 Add New Service ..................................................................................................................................................29 Add New Rule .......................................................................................................................................................31 Delete Rules or Services ......................................................................................................................................31

PROVIDERS ........................................................................................................................................ 31 Hardware Trunks ....................................................................................................................................................31 Connection Types ..................................................................................................................................................31 Provisioning a New Hardware Trunk Group ........................................................................................................32 Configuring Hardware Trunks......................................................................................................................................................... 34

Add Phone Numbers to Hardware Provider ...................................................................................................................38 Remove Phone Numbers from Hardware Provider .......................................................................................................39

Provisioning SIP Providers ...................................................................................................................................39 Add New SIP Provider ..........................................................................................................................................44 Add Phone Numbers ........................................................................................................................................................45 Remove Phone Numbers .................................................................................................................................................45 Set Destination .................................................................................................................................................................46

Delete SIP Provider ..............................................................................................................................................46

DESTINATIONS .................................................................................................................................. 47 Extensions...............................................................................................................................................................48 Add/Import Tab .....................................................................................................................................................48 Add/Create Extensions ....................................................................................................................................................50

Search Tab ...........................................................................................................................................................51 Search Extension .............................................................................................................................................................51

View Tab (Extensions) ..........................................................................................................................................52 Edit or View Extension.....................................................................................................................................................52 Mass Edit PBX Extension Settings .................................................................................................................................52 Mass Edit Phone Key Settings ........................................................................................................................................53 Delete Extension...............................................................................................................................................................54 Delete Multiple Extension ................................................................................................................................................54

Extensions - General Settings Section .................................................................................................................55 Extensions - Forward Settings Section.................................................................................................................57 Enable/Disable Forward Settings....................................................................................................................................58 Change Unconditional Forwarding via Keypad .............................................................................................................58 Change Unconditional Forwarding via PC .....................................................................................................................59 Change Forwarding Number While Away from an Extension ......................................................................................59

Extensions - Advanced Settings ...........................................................................................................................60

IPitomy IP PBX Admin Guide Extensions - Network Settings Section.......................................................................................................................... 60 Edit Extensions - Network Settings................................................................................................................................................. 62

Extensions - Voicemail Settings Section ....................................................................................................................... 63 Edit Voicemail Settings .................................................................................................................................................................... 65

Extensions - Allow CODECs Section ............................................................................................................................. 66 Edit CODEC Settings........................................................................................................................................................................ 66

Extensions Calling Permissions Section....................................................................................................................... 67 Add/Edit Calling Permissions.......................................................................................................................................................... 68

Extensions - Follow-Me Section ..................................................................................................................................... 69 Add/Edit Follow Me Settings............................................................................................................................................................ 70

Provisioning - Auto-Discovery Tab........................................................................................................................71 Start Auto-Discovery Scan.............................................................................................................................................. 71 List of Devices & Extensions .......................................................................................................................................... 72 Device Information........................................................................................................................................................... 73 Edit Selected Tab ............................................................................................................................................................. 74 Create, Assign and Configure Phone.............................................................................................................................................. 74

View Settings Tab ............................................................................................................................................................ 75 Advanced Filter Settings.................................................................................................................................................................. 76 Advanced Scan Settings.................................................................................................................................................................. 77

Commands Tab ................................................................................................................................................................ 78 Factory Default Phone...................................................................................................................................................................... 79 Troubleshooting Network Scanning Problems............................................................................................................................... 79 Auto Provisioning Phone Settings from Actual Device ................................................................................................................. 80

Edit Phone Settings...............................................................................................................................................80 View Phone Settings........................................................................................................................................................ 80 Edit Phone Settings ......................................................................................................................................................... 81

Edit Advance Phone Settings ...............................................................................................................................83 Edit Advance Phone Settings – Aastra Phones ............................................................................................................ 86

Groups .....................................................................................................................................................................88 Ring Group Examples ...........................................................................................................................................89 Example Ring Group 1 – Departmental Grouping......................................................................................................... 89 Example Ring Group 2 – Regional Sales Grouping ...................................................................................................... 89 Add/Edit New Ring Group ............................................................................................................................................... 90 Ring Group Advanced Settings ...................................................................................................................................... 94 Edit Advanced Ring Group Settings .............................................................................................................................. 95 Edit Custom Caller ID Settings ....................................................................................................................................... 95 Edit Members/Agents ...................................................................................................................................................... 96 Add Agents/Members to the Group................................................................................................................................ 97 Delete Agents/Members from the Group ....................................................................................................................... 97

Automatic Call Distribution (ACD) .........................................................................................................................98 Edit Automatic Call Distribution (ACD) Settings......................................................................................................... 100 Add Automatic Call Distribution (ACD) Agents........................................................................................................... 101 Edit Automatic Call Distribution (ACD) Agent............................................................................................................. 102 Delete Automatic Call Distribution (ACD) Agent......................................................................................................... 102

Multicast Paging Group.......................................................................................................................................103 Add Multicast Paging Group......................................................................................................................................... 104 Edit Multicast Paging Group ......................................................................................................................................... 105 Delete Multicast Paging Group ..................................................................................................................................... 105

Live Queue Data .................................................................................................................................................106 Live Queue Data – Wallboard.............................................................................................................................107 Activate Live Call Queue Wallboard............................................................................................................................. 107

Menus.....................................................................................................................................................................109 Edit Menu ............................................................................................................................................................110 Add Menu Settings ........................................................................................................................................................ 111 Edit Menu Settings......................................................................................................................................................... 112

IPitomy IP PBX Admin Guide Delete Menu Settings .....................................................................................................................................................112 Advanced Menu Settings...............................................................................................................................................113

Conferences ..........................................................................................................................................................115 Add/Edit Conference ......................................................................................................................................................116

Conference Feature Codes.................................................................................................................................117 Voicemail ...............................................................................................................................................................118 Add Voicemail Settings ................................................................................................................................................................. 120 Edit Voicemail Settings.................................................................................................................................................................. 121 Clear Voicemail Messages ............................................................................................................................................................ 121 Delete Voicemail Box..................................................................................................................................................................... 121 Broadcast Message – Add............................................................................................................................................................. 122 Broadcast Message – Remove...................................................................................................................................................... 122

Cascading Message Notification...................................................................................................................................122 Set Cascading Messages .............................................................................................................................................................. 123 Setting Cascading Interval ............................................................................................................................................................ 123 Configure Contact Numbers for Cascading Message Notification ............................................................................................. 124

Schedules..............................................................................................................................................................126 Add Schedule......................................................................................................................................................127 Add Holiday to Schedule ...............................................................................................................................................127 Remove Holiday from Schedule....................................................................................................................................128

Edit Schedule ......................................................................................................................................................128 Delete Schedule..................................................................................................................................................128 Branch Offices ......................................................................................................................................................129 Configuring Office 1 ............................................................................................................................................132 Configuring Office 2 ............................................................................................................................................133 Edit Branch Office ...............................................................................................................................................134 Delete Branch Office...........................................................................................................................................134 Branch Extensions ..............................................................................................................................................134 Configuring Office 2 with Branch Extensions..............................................................................................................135 View Branch Office Extensions.....................................................................................................................................136

Call Routing...........................................................................................................................................................137 Incoming Call Routing.........................................................................................................................................137 Set Default Incoming Destination .................................................................................................................................138 Set Provider Trunk Incoming Destination ...................................................................................................................139 Enable/Disable Day/Night Mode ....................................................................................................................................139 Switch Day/Night Mode ..................................................................................................................................................139 Edit Hours .......................................................................................................................................................................140 Edit Incoming Caller DID................................................................................................................................................140

Outgoing Call Routing.........................................................................................................................................141 Add Outgoing Route ......................................................................................................................................................145 Edit Outgoing Route.......................................................................................................................................................145 Delete Outgoing Route...................................................................................................................................................146

Class of Service ..................................................................................................................................................147 Outgoing Call Routing.........................................................................................................................................148 Configure Block Calls Subroutes..................................................................................................................................148 Configure Least Cost Routing Subroutes ....................................................................................................................149 Configure Information (411/1411) Subroute .................................................................................................................150

PBX SETUP....................................................................................................................................... 151 General System Setup .........................................................................................................................................151 Admin Settings Section.......................................................................................................................................151 Edit Admin Settings .......................................................................................................................................................152

IPitomy IP PBX Admin Guide General Settings Section ....................................................................................................................................152 Edit General PBX Settings ............................................................................................................................................ 153

Security Settings Section ....................................................................................................................................155 Log Watch/Ban Service ................................................................................................................................................. 155 Enable Log Watch/Ban Service .................................................................................................................................... 155 Set Log Watch/Ban Service Parameters ...................................................................................................................... 155 Configure Log Watch/Ban Service ............................................................................................................................... 156 Disable Log Set Security Setting.................................................................................................................................. 157

Time Settings Section .........................................................................................................................................157 Set Time Settings........................................................................................................................................................... 158

Outbound Transfers Numbers Section ...............................................................................................................159 Add Outbound Transfers............................................................................................................................................... 159 Delete Outbound Transfers........................................................................................................................................... 159

InGenius Connector ............................................................................................................................................160 Database Administration .....................................................................................................................................161 Create Backup Section .......................................................................................................................................161 Creating a Backup ......................................................................................................................................................... 161

Automatic Backups Section ................................................................................................................................162 Set Automatic Backup................................................................................................................................................... 163

Upload Backup File Section ................................................................................................................................163 Upload Backup Files...................................................................................................................................................... 164

Backup Storage Section......................................................................................................................................164 Delete Backup File ......................................................................................................................................................... 165 Restore Backup File ...................................................................................................................................................... 165 Download Backup File................................................................................................................................................... 166

Voicemail Setup ....................................................................................................................................................166 General Settings Section ....................................................................................................................................166 Set General Voicemail Settings .................................................................................................................................... 167

Voicemail Menu Section......................................................................................................................................167 Set Voicemail Menu Options......................................................................................................................................... 168

E-mail Settings Section .......................................................................................................................................169 Set E-mail Settings ........................................................................................................................................................ 170 Test Settings Button...................................................................................................................................................... 170

Voicemail Archive Section...................................................................................................................................171 Download Voicemail Archive Settings......................................................................................................................... 171 Erase Voicemail Archive Settings ................................................................................................................................ 172 Upload Voicemail Archive Settings.............................................................................................................................. 172 View Voicemail Listing (Usage Space)......................................................................................................................... 172

SIP Setup ...............................................................................................................................................................173 SIP Networking Settings Section ........................................................................................................................173 Add SIP Networking Settings........................................................................................................................................ 174 Delete SIP Networking Settings.................................................................................................................................... 174

SIP Advanced Settings Section ..........................................................................................................................175 Edit Advanced SIP Networking Settings...................................................................................................................... 181

Prompts .................................................................................................................................................................181 Upload Voice Prompt Section .............................................................................................................................181 Upload Voice Prompt..................................................................................................................................................... 181

Record New Voice Prompt Section.....................................................................................................................182 Record New Voice Prompt ............................................................................................................................................ 182

Prompt Files on Server Section ..........................................................................................................................183

IPitomy IP PBX Admin Guide Delete Prompt Files on Server.......................................................................................................................................183 Download Prompt Files on Server ................................................................................................................................183

Music on Hold .......................................................................................................................................................184 Systems Default Music on Hold Section.............................................................................................................184 Set Default Music on Hold Section ...............................................................................................................................184

Create a Playlist Section.....................................................................................................................................185 Add New Music on Hold.................................................................................................................................................185 Upload Music Files .........................................................................................................................................................186 Delete Music Files on Server .........................................................................................................................................186

Feature Codes.......................................................................................................................................................187 Speed Dialing Section.........................................................................................................................................187 Add Speed Dialing..........................................................................................................................................................187 Edit Speed Dialing ..........................................................................................................................................................188 Delete Speed Dialing ......................................................................................................................................................188 Import/Export Speed Dialing List (CSV) .......................................................................................................................188

Services .................................................................................................................................................................189 System Information Section ................................................................................................................................189 View System Information...............................................................................................................................................190

License Information Section................................................................................................................................190 Upload License File........................................................................................................................................................191 Download License File...................................................................................................................................................191 Assign Single User License...........................................................................................................................................192 Assign Multiple User Licenses......................................................................................................................................193

System Functions Section ..................................................................................................................................193 Restart PBX.....................................................................................................................................................................194 Reboot PBX.....................................................................................................................................................................194 Restart Services .............................................................................................................................................................194 Restart Call Manager......................................................................................................................................................195 Clear Diagnostics ...........................................................................................................................................................195

Load File System ................................................................................................................................................195 TFTP Files...........................................................................................................................................................196 Load TFTP File................................................................................................................................................................196 Download TFTP File .......................................................................................................................................................196 Delete TFTP File..............................................................................................................................................................196

Log File Settings .................................................................................................................................................197 Select Log File Settings .................................................................................................................................................197

Logging Level Section.........................................................................................................................................198 Select Logging Level......................................................................................................................................................198

Call Event Log Section........................................................................................................................................199 Set Call Event Logging ..................................................................................................................................................199

Automated Phone Firmware Updates.................................................................................................................200 Set Automated Firmware Update Parameters..............................................................................................................200 Check for New Firmware Now .......................................................................................................................................200

Scheduled Calling ...............................................................................................................................................201 Enabling Scheduled Calling ..........................................................................................................................................201 Adding a New Scheduled Call .......................................................................................................................................204 Edit a Scheduled Call .....................................................................................................................................................205 Edit a Scheduled Call .....................................................................................................................................................205 Test a Scheduled Call ....................................................................................................................................................205

REPORTING...................................................................................................................................... 205 Reports ..................................................................................................................................................................205

IPitomy IP PBX Admin Guide View CDR Report – Smart Personal Console .............................................................................................................. 208 View CDR Report – PBX Administration ...................................................................................................................... 209 Export CDR Report ........................................................................................................................................................ 209

Queue Graphs .......................................................................................................................................................209 Run Queue Graph Report.............................................................................................................................................. 210 Overview Tab .................................................................................................................................................................................. 211 Agents Tab...................................................................................................................................................................................... 212 Graph Tab ....................................................................................................................................................................................... 213 Logs Tab ......................................................................................................................................................................................... 213

Diagnostics............................................................................................................................................................214 View System Diagnostics....................................................................................................................................214 Monitoring .............................................................................................................................................................215

APPENDICES.................................................................................................................................... 216 Appendix 1: Key Types and Codes.....................................................................................................................216 Appendix 2: IP Telephones..................................................................................................................................219 IPitomy 550 .........................................................................................................................................................219 IPitomy 55i ..........................................................................................................................................................219 IPitomy 53i ..........................................................................................................................................................219 IPitomy 53i IP Phone...........................................................................................................................................220 IPitomy 57i ..........................................................................................................................................................220 6739i....................................................................................................................................................................220 IP120 ...................................................................................................................................................................220 IP51i ....................................................................................................................................................................221 IPitomy 536M ......................................................................................................................................................221 IPitomy 560M ......................................................................................................................................................221

APPENDIX 3: SOFTPHONES ........................................................................................................... 222 ®

®

CounterPath™ eyeBeam 1.5 and X-Lite 3.0....................................................................................................222 What is a Softphone?..........................................................................................................................................222 ® X-Lite 3.0 Free Softphone .................................................................................................................................222 ® eyeBeam 1.5 (Pricing available at www.counterpath.com)...............................................................................222 Softphone Installation..........................................................................................................................................223 Forward Settings .................................................................................................................................................224 Provisioning Forward Settings ..................................................................................................................................... 224 Changing a Forwarding Number from an Extension .................................................................................................. 224 Changing a Forwarding Number from a PC................................................................................................................. 225 Changing a Forwarding Number While Away from an Extension ............................................................................. 225

Advanced Settings ..............................................................................................................................................225 Network Settings............................................................................................................................................................ 225

APPENDIX 4: IP ADDRESSES ......................................................................................................... 226 Determining Local Network Address (on a Microsoft Windows Machine) .................................................226 Determining an Available IP Address.................................................................................................................226

APPENDIX 5: DHCP SETTINGS ....................................................................................................... 227 Leasing Time for an IP Address ..........................................................................................................................227 Determining/Viewing DHCP Settings on a Linksys Router ...............................................................................227 Tips for Understanding the IP Address List ........................................................................................................227

APPENDIX 6: ROUTER CONFIGURATION ...................................................................................... 228

IPitomy IP PBX Admin Guide APPENDIX 7: NETWORK CONSOLE............................................................................................... 228 Accessing the Network Console.........................................................................................................................228 Selecting Options................................................................................................................................................228 Menus ....................................................................................................................................................................229 Menu Location ....................................................................................................................................................229 Using the “Live” System Settings ......................................................................................................................229 Database Settings...............................................................................................................................................229 Command Options ..............................................................................................................................................229 Refresh View [R] .............................................................................................................................................................229 Default Settings [D] ........................................................................................................................................................229 Save & Update [S]...........................................................................................................................................................229 Disable [Z] .......................................................................................................................................................................229

Network Type ......................................................................................................................................................230 DHCP ...............................................................................................................................................................................230 Acquiring a DHCP Lease ............................................................................................................................................................... 230 Renewing DHCP Lease.................................................................................................................................................................. 230

Other Menus .......................................................................................................................................................230 Web Server .........................................................................................................................................................230 Host Access ........................................................................................................................................................230 Fix Database .......................................................................................................................................................231 Tips for Using the IPitomy IP PBX Network Console .........................................................................................231

APPENDIX 8: SOFTWARE UPGRADE............................................................................................. 232 APPENDIX 9: TROUBLESHOOTING (FAQ) ..................................................................................... 234 GLOSSARY ....................................................................................................................................... 235 NOTES: ............................................................................................................................................. 241

IPitomy IP PBX Admin Guide

LIST OF FIGURES Figure 1 – IPitomy IP PBX System ............................................................................................................................ 2 Figure 2 – Hardware Setup Diagram......................................................................................................................... 6 Figure 3 – External Gateway Connection Diagram ................................................................................................... 8 Figure 4 – SIP Provider Connection Diagram ........................................................................................................... 8 Figure 5 – LAN Connection Diagram......................................................................................................................... 9 Figure 6 – IP120 and IP1500 Connector Ports.......................................................................................................... 9 Figure 7 – Sample Setup Worksheet....................................................................................................................... 10 Figure 8 – View of Upload Location Window........................................................................................................... 12 Figure 9 – Create Extension Results Page ............................................................................................................. 13 Figure 10 – Port Forwarding Configuration Table ................................................................................................... 14 Figure 11 – Typical Network Configuration Diagram............................................................................................... 16 Figure 12 – Administration Menu Options ............................................................................................................... 17 Figure 13 – Standard Page Layout and Features ..................................................................................................... 1 Figure 14 – View of Mouse Over Field Information ................................................................................................. 19 Figure 15 – IP PBX ADMIN Login Page .................................................................................................................. 20 Figure 16 – Networking Setup Page........................................................................................................................ 21 Figure 17 – PBX Host Access Page ........................................................................................................................ 23 Figure 18 – Web Server Configuration Page........................................................................................................... 24 Figure 19 – Access Control List - Add New Rule Section ....................................................................................... 28 Figure 20 – Access Control List Page - Add New Service Section ......................................................................... 29 Figure 21 – Hardware Providers Trunk Setup Page ............................................................................................... 32 Figure 22 – Add/Edit Hardware Provider Configuration Page................................................................................. 35 Figure 23 – SIP Providers Configuration Main Page............................................................................................... 39 Figure 24 – Add/Edit SIP Provider Configuration Page 1........................................................................................ 40 Figure 25 – Add/Edit SIP Provider Configuration Page 2........................................................................................ 41 Figure 26 – IP PBX Data Components.................................................................................................................... 47 Figure 27 – Extensions Add/Import Page................................................................................................................ 49 Figure 28 – Create Extensions Page....................................................................................................................... 49 Figure 29 – Search Extension Page ........................................................................................................................ 51 Figure 30 – Extensions View Page.......................................................................................................................... 52 Figure 31 - Extensions View Tab (Mass Edit Feature) ............................................................................................ 53 Figure 32 – Extensions General Settings Section ................................................................................................... 55 Figure 33 – Extensions Forward Settings Section .................................................................................................. 57 Figure 34 – Extensions Advanced Network Settings Page ..................................................................................... 60 Figure 35 – Extensions Voicemail Settings Section ................................................................................................ 63 Figure 36 – Extensions CODECS Settings Page .................................................................................................... 66

Copyright  2011 IPitomy Communication, LLC

v4.0.1

IPitomy IP PBX Admin Guide Figure 37 – Extensions Calling Permissions Section ...............................................................................................67 Figure 38 – Extensions Advanced Settings Follow Me Setup Page ........................................................................69 Figure 39 – Extensions Auto-Discovery Tab ............................................................................................................71 Figure 40 – Auto-Discovery Device Color Legend ...................................................................................................72 Figure 41 – Auto- Discovery Device Values.............................................................................................................73 Figure 42 – Auto-Discovery Edit Selected Functions ...............................................................................................74 Figure 43 – Auto-Discovery View Settings Page......................................................................................................75 Figure 44 – Auto-Discovery Advanced Filter Settings..............................................................................................76 Figure 45 – Auto-Discovery Advanced Scan Settings Page ....................................................................................77 Figure 46 – Auto-Discovery Command Functions Page ..........................................................................................78 Figure 47 – Extension Listing ...................................................................................................................................80 Figure 48 – Edit Phone Settings Page .....................................................................................................................81 Figure 49 – Aastra Advanced Phone Settings Page ................................................................................................86 Figure 50 – Ring Groups Page.................................................................................................................................88 Figure 51 – Edit Ring Group Page ...........................................................................................................................91 Figure 52 – Advanced Ring Group and Custom Caller ID Settings Section ............................................................94 Figure 53 – Edit Members/Agents Section...............................................................................................................96 Figure 54 – ACD Edit Agents Page ........................................................................................................................101 Figure 55 – Multicast Paging Groups Page............................................................................................................103 Figure 56 – Edit Page Group Window....................................................................................................................103 Figure 57 – Ring Group Live Queue Data..............................................................................................................106 Figure 58 – Menus Page ........................................................................................................................................109 Figure 59 – Edit Menus Page (with Control Menu Prompts open).........................................................................110 Figure 60 – Advanced Menu Settings Page...........................................................................................................113 Figure 61 – Remote Menu Announcement DTMF Admin Flow ........................................................................114 Figure 61 – Conferences Page...............................................................................................................................115 Figure 62 - Edit Conference ...................................................................................................................................115 Figure 63 – Features Code Page ...........................................................................................................................117 Figure 64 – Edit Voicemail Box Settings Page.......................................................................................................118 Figure 65 – Notification Settings / Voicemail Box Page .........................................................................................124 Figure 66 – Edit Schedule and Holidays Page.......................................................................................................126 Figure 68 – Sample Branch Office Networking ......................................................................................................129 Figure 69 – Edit Branch Office Page ......................................................................................................................130 Figure 70 – Branch Offices Page ...........................................................................................................................132 Figure 71 – Branch Office Extension Section.........................................................................................................135 Figure 72 – Show Extensions Page .......................................................................................................................136 Figure 73 – Incoming Call Routing Page................................................................................................................137

Copyright  2011 IPitomy Communication, LLC

v4.0.1

IPitomy IP PBX Admin Guide Figure 74 – Incoming Routing Edit Incoming DID CID Page................................................................................. 140 Figure 75 – Outgoing Routing Page ...................................................................................................................... 142 Figure 76 – Add New Outgoing Route Page ......................................................................................................... 143 Figure 77 - Class of Service .................................................................................................................................. 147 Figure 78 – Blocking Dialing 1-900........................................................................................................................ 148 Figure 79 – Least Cost Routing Example.............................................................................................................. 149 Figure 80 – Information (411) Subroute Setting .................................................................................................... 150 Figure 81 – PBX Admin Settings Section .............................................................................................................. 151 Figure 82 – PBX General Settings Section ........................................................................................................... 152 Figure 83 – PBX Security Log Watch and Ban Service Status ............................................................................. 155 Figure 84 – Security Log Watch and Ban Security Settings.................................................................................. 155 Figure 85 – PBX Time Settings Section ................................................................................................................ 157 Figure 86 – Outbound Transfer Numbers Section................................................................................................. 159 Figure 87 – InGenius Connector Settings Section ................................................................................................ 160 Figure 88 – Create Backup Section....................................................................................................................... 161 Figure 89 – PBX Database Automatic Backups Section....................................................................................... 162 Figure 90 – PBX Database Upload Backup File Section ...................................................................................... 163 Figure 91 – Backup Date/Time Information........................................................................................................... 165 Figure 92 – PBX Voicemail General Settings Section........................................................................................... 166 Figure 93 – PBX Voicemail Menu Section............................................................................................................. 167 Figure 94 – PBX Voicemail Settings Section......................................................................................................... 169 Figure 95 – PBX Voicemail Archive Section.......................................................................................................... 171 Figure 96 – PBX Voicemail Listing Page............................................................................................................... 172 Figure 97 – SIP Networking Settings Page ........................................................................................................... 173 Figure 98 – SIP Advanced Settings Page ............................................................................................................. 178 Figure 99 – Upload Voice Prompt Section ............................................................................................................ 181 Figure 100 – Record New Voice Prompt Section .................................................................................................. 182 Figure 101 – Prompt Files on the Server Section.................................................................................................. 183 Figure 102 – System Default Music on Hold Section ............................................................................................ 184 Figure 103 – Create a Playlist Section .................................................................................................................. 185 Figure 104 – Music on Hold Playlist ...................................................................................................................... 186 Figure 105 – Features Code Speed Dialing Section ............................................................................................. 187 Figure 106 – Services System Information Page .................................................................................................. 189 Figure 107 – Services Download License Information Section ............................................................................. 190 Figure 108 – Services Assign Licenses Page ....................................................................................................... 192 Figure 109 – Services System Functions Section ................................................................................................. 193 Figure 110 - Services Load File System Section .................................................................................................. 195

Copyright  2011 IPitomy Communication, LLC

v4.0.1

IPitomy IP PBX Admin Guide Figure 111 – Services TFTP Files Section.............................................................................................................196 Figure 112 – Services Log File Settings Section....................................................................................................197 Figure 113 – Services Logging Level Section ........................................................................................................198 Figure 114 – Services Call Event Log Section .......................................................................................................199 Figure 115 – Services Automated Phone Firmware Updates ................................................................................200 Figure 116 - Scheduled Calling ..............................................................................................................................201 Figure 117 - List of Scheduled Calls ......................................................................................................................201 Figure 118 - Edit Scheduled Call............................................................................................................................203 Figure 119 - Recurrence.........................................................................................................................................204 Figure 120 – CDR Reports Page ...........................................................................................................................206 Figure 121 – Queue Graphs Page .........................................................................................................................209 Figure 122 – Reports Queue Graph Overview Tab................................................................................................211 Figure 123 – Reports Queue Graphs Agents Tab..................................................................................................212 Figure 124 – Reports Queue Graphs Tab..............................................................................................................213 Figure 125 – Reports Queue Graphs Logs Tab .....................................................................................................213 Figure 126 – System Diagnostics Page .................................................................................................................214 Figure 127 – Monitoring Page ................................................................................................................................215

Copyright  2011 IPitomy Communication, LLC

v4.0.1

IPitomy IP PBX Admin Guide

LIST OF TABLES Table 1 – IP PBX Features ........................................................................................................................................ 4 Table 2 – Setup Worksheet Descriptions ................................................................................................................ 11 Table 3 – Sample Exported .CSV Worksheet ......................................................................................................... 12 Table 4 – Feature and Link Descriptions................................................................................................................. 18 Table 5 – Navigational Buttons and Links ............................................................................................................... 19 Table 6 – Network Setting Descriptions .................................................................................................................. 22 Table 7 – Network Features and Descriptions ........................................................................................................ 23 Table 8 – Web Server Features and Descriptions .................................................................................................. 25 Table 9 – Access Control List Definitions ................................................................................................................ 29 Table 10 – Add New Service Settings and Descriptions ......................................................................................... 30 Table 11 – Add New Rule Settings and Descriptions.............................................................................................. 30 Table 12 – Hardware Trunk Provider Settings and Descriptions ............................................................................ 34 Table 13 – Hardware Provider Configuration Settings and Descriptions ................................................................ 38 Table 14 – SIP Provider Configuration Settings and Descriptions .......................................................................... 44 Table 15 – Create Extension Fields and Descriptions ............................................................................................ 50 Table 16 – Search Extension Parameters and Description..................................................................................... 51 Table 17 – General Extension Settings and Descriptions ....................................................................................... 56 Table 18 – Extension Forward Settings and Descriptions....................................................................................... 57 Table 19 – Extensions Advanced Networking Settings and Descriptions ............................................................... 62 Table 20 – Voice Mail Settings and Descriptions .................................................................................................... 65 Table 21 – Extensions CODECS Settings and Recommendations ........................................................................ 66 Table 22 – Calling Permission Settings and Descriptions....................................................................................... 68 Table 23 – Extensions Follow Me Settings and Descriptions.................................................................................. 70 Table 24 – Auto-Discovery Scan Details ................................................................................................................. 73 Table 25 – Auto-Discovery Edit Selected Tab Functions and Descriptions ............................................................ 74 Table 26 – Auto-Discovery Functions and Descriptions.......................................................................................... 76 Table 27 – Advanced Filter Settings and Descriptions............................................................................................ 77 Table 28 – Auto-Discovery Advanced Scan Settings and Descriptions .................................................................. 78 Table 29 – Auto-Discovery Command Settings and Descriptions........................................................................... 78 Table 30 – Edit Phone Settings and Descriptions ................................................................................................... 82 Table 31 – Edit Advanced Phone Settings – IPitomy Phones................................................................................. 83 Table 32 – Edit Advanced Phone Settings for IPitomy Phones .............................................................................. 85 Table 33 – Aastra Advanced Phone Settings and Descriptions.............................................................................. 87 Table 34 – Edit Ring Group Settings and Descriptions ........................................................................................... 92 Table 35 – Advanced Ring Group and Custom Caller ID Settings and Descriptions.............................................. 94 Table 36 – Edit Members/Agents Settings and Descriptions .................................................................................. 96

Copyright  2011 IPitomy Communication, LLC

v4.0.1

IPitomy IP PBX Admin Guide Table 37 – Automatic Call Distribution (Agents) Page .............................................................................................98 Table 38 – Edit Ring Group ACD Agents Settings and Descriptions .....................................................................100 Table 39 – Add/Edit Agent Features and Descriptions ..........................................................................................101 Table 40 – Multicast Paging Settings and Descriptions .........................................................................................104 Table 41 – Live Queue Fields and Descriptions.....................................................................................................107 Table 42 – Add/Edit Settings and Descriptions ......................................................................................................111 Table 43 – Advanced Settings and Description .....................................................................................................113 Table 44 – Conference Settings and Descriptions .................................................................................................116 Table 45 – Features Code Settings and Descriptions............................................................................................117 Table 46 - Voice Mailbox Settings and Descriptions ..............................................................................................120 Table 47 – Notification and Voicemail Box Settings and Descriptions...................................................................125 Table 48 – Edit Schedule Settings and Descriptions .............................................................................................127 Table 49 – Branch Office Settings and Descriptions..............................................................................................131 Table 50 – Incoming Call Routing Settings and Descriptions ................................................................................138 Table 51 - Outbound Routing Page Descriptions...................................................................................................141 Table 52 – Outbound Route Settings and Descriptions .........................................................................................145 Table 53 – Block 1900 Outbound Call Configuration .............................................................................................149 Table 54 – Least Cost Outbound Call Subroute Configuration ..............................................................................150 Table 55 – Information (411) Subroute Configuration ............................................................................................151 Table 56 – PBX Admin Settings Parameters and Descriptions .............................................................................152 Table 57 – General PBX Admin Settings and Descriptions ...................................................................................153 Table 58 – PBX Security Log Watch/Ban Settings and Descriptions.....................................................................156 Table 59 – PBX Time Settings and Descriptions ...................................................................................................158 Table 60 – Create Backup Settings and Descriptions............................................................................................161 Table 61 – PBX Database Automatic Backup Settings and Descriptions..............................................................163 Table 62 - Saved Backups .....................................................................................................................................164 Table 63 – PBX General Settings and Descriptions...............................................................................................167 Table 64 – PBX Voicemail Menu Setting and Descriptions ...................................................................................168 Table 65 – PBX Voicemail Settings and Descriptions............................................................................................170 Table 66 – PBX Voicemail Archive Settings and Descriptions...............................................................................171 Table 67 – SIP Networking Settings and Descriptions...........................................................................................173 Table 68 – SIP Advanced Settings and Descriptions.............................................................................................181 Table 69 – Features Code Settings and Descriptions............................................................................................187 Table 70 – Services System Settings and Descriptions.........................................................................................190 Table 71 - License Info Descriptions ......................................................................................................................191 Table 72 – Services System Functions and Descriptions ......................................................................................194 Table 73 – Services Log File Settings and Descriptions ........................................................................................197

Copyright  2011 IPitomy Communication, LLC

v4.0.1

IPitomy IP PBX Admin Guide Table 74 – Services Logging Levels and Descriptions.......................................................................................... 198 Table 75 – Services Call Event Logging and Descriptions.................................................................................... 199 Table 76 – Services Automated Firmware Parameters and Descriptions............................................................. 200 Table 77 - Scheduled Call List Descriptions.......................................................................................................... 202 Table 78 - Edit Scheduled Call Descriptions ......................................................................................................... 203 Table 79 - Recurrence Descriptions ...................................................................................................................... 204 Table 80 - CDR Report Descriptions ..................................................................................................................... 207 Table 81 – Queue Graphs Search Parameters ..................................................................................................... 210

Copyright  2011 IPitomy Communication, LLC

v4.0.1

IPitomy IP PBX Admin Guide

INTRODUCTION About the IPitomy IP PBX The IPitomy IP PBX is a powerful business communications platform. It is a pure IP PBX designed to use IP networks for voice calls. Engineered to support from 10 to 500 users, the system will work with analog lines and T1 /PRI lines for traditional Public Switched Telephone Network (PSTN) connectivity. In addition to traditional telephone lines, the IPitomy IP PBX can use VoIP SIP Trunks, replacing traditional PSTN lines with a broadband telephone service.

Benefits of VoIP Technology The IPitomy IP PBX can support any or all of these connectivity methods simultaneously or in any combination. Customers not quite ready to depend on VoIP providers for all of their business communications can start at their own pace and gain a comfort level, shifting to VoIP broadband providers at their own pace. Benefits of VoIP technology include: •

One Wiring System − The system uses a single wiring system for telephones and dataall data and voice are on Local Area Network (LAN) Category 5 wiring.



Web-based Administration − System administration is performed on the network through a Webbased administration program. The Web-Based Administration can be used locally or remotely from anywhere.



Remote Users − When calls are routed over the Internet, long distance charges can be avoided. In businesses with remote workers, these employees can stay logged into the office through a broadband connection at all times without incurring any additional charges. Remote users have all of the features of the local users. Remote users can be included in any ring groups, ACD (Automatic Call Distribution) Queues and other call routing schemes.



Centralized System Features − Every extension that is logged into the system is capable of receiving and originating calls. The use of system features such as voicemail, automated attendant and email are all centralized simplifying all support and maintenance.



Reduced Costs − VoIP system users can reduce cost in many areas of a business. VoIP telephony lowers the cost of support and maintenance costs, as well as, reducing telephony line costs by up to 50%.



Simplifies Administration − Moves, additions and changes are simple. The IPitomy IP PBX provides enhanced capabilities for users to make changes without incurring a service call.



Investment Protection − VoIP, and in particular, Session Initiation Protocol (SIP)-based VoIP products offer investment protection. The industry is rapidly moving toward Internet Protocol (IP) communications technologies. Older digital and analog technologies are becoming obsolete and are being replaced with IP-based products that will be around for a long time.

IPitomy IP PBX Features Understanding the IPitomy IP PBX’s architecture and how it works will make installing the system simple. The IPitomy IP PBX is an all-in-one business communications system. This powerful system includes a complete suite of business communication applications in one appliance: •

Fully-featured Business Phone System



Automated Attendant and Interactive Voice Response (IVR)



Enhanced Call Distribution

2011 Copyright  IPitomy Communication, LLC

1 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide •

Enhanced Voice Messaging System with Unified Messaging



Meet-me Conference Application



Built-in Music on Hold



Call Queuing for Inbound Calls



Find Me/Follow Me



Remote Extensions



Browser-based Administration



Branch Offices



Automatic Call Distribution (ACD)

Figure 1 – IPitomy IP PBX System

The IPitomy IP PBX’s administration menus are a series of Web pages accessible from a Web browser. To the left of the Menu is a navigation bar that allows users to click on and administer each section of the system. Administration of the IPitomy IP PBX is simple and intuitive. The system is designed with six primary areas of functionality: •

System − System setup consists of network configuration settings.



Providers − Providers are sources of PSTN and VoIP connectivity. Providers are the lines that handle all incoming and outgoing calls. All VoIP and traditional telephone providers are setup here. DID numbers are also entered here.



Destinations − Destinations are places where calls are routed in the system: extensions, groups of extensions, automated attendants, conferences, and voicemail.



Call Routing − These settings route inbound calls to specific destinations within the system, and send outbound calls over specific local, long distance, international, and emergency routes.



PBX Setup − These settings globally configure PBX timers, voice messaging, and other system features.



Reporting − These reports display system usage, monitor activity, and provide diagnostic information.

2011 Copyright  IPitomy Communication, LLC

2 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide Feature

Description

Extensions

Extensions are telephones. A telephone can be an IP (SIP) telephone or a Softphone. Calls are routed to an extension where people answer them. In the IPitomy IP PBX, an extension can be located in an office or outside the office where a broadband connection is used.

Groups

Groups are a set of extensions. Once a group is created, extensions can be designated as members of the group. This is accomplished by selecting group members from a dropdown list. Calls can be routed to groups via inbound routing. To create an automated attendant use the system’s Menus feature. The Menus feature allows you to route calls to a destination in the system like a group, extension or another menu.

Menus (Automated Attendant)

Call Destinations are selected from a drop-down list for each corresponding key-pad digit a caller must select to get to their chosen destination. A Menu must have a Menu Prompt. This is a recording that identifies for callers the destinations they may choose. For example, a Menu Prompt might offer callers the option to press “1” for Sales, “2” for Accounts Receivable or other digits for another department.

DTMF Menu Administration

New in version: 3.4.1 is DTMF Menu Administration. This feature allows the user to administer the Menu (Auto Attendant) remotely using just a telephone (with DTMF dial capability).

Advanced Routing Functions

When building an automated attendant (Menus) all routable destinations in the system will appear in the drop-down list. In addition to the destinations that are created while configuring the system, there are several advanced functions that can be used from the drop-down list.

Voicemail and Unified Messaging

When an extension is created, a voicemail box for that extension is also created. A voicemail box allows a caller to leave a message if a person is not available at the extension. When dialing into a mailbox for the first time, a user should record their name and a mailbox greeting. The name is used in the company’s dial-by-name directory when selected from the auto attendant (Menus). The greeting is played when they are not available to take a call and a caller reaches their mailbox. If an email address is included in the Extension page, you can configure Unified Messaging and a copy of the voicemail message will be emailed as a .Wav file to the users email account. This message can then be listened to on a PC.

Directory

The system has a dial-by-name directory. This option may be part of the automatedattendant. When this option is selected, a caller dials the first three letters of the last / first name of the party they would like to reach. Names that match these three letters are played and the caller selects the extension to which they want to be transferred. Names are stated in the directory as they have been recorded by users in their voicemail box, and spelt out if they have not recorded their name.

Direct Inward Dialing (DID) Numbers

A Direct Inward Dialed (DID) number is a telephone number assigned by a service provider (i.e., T1 line, PRI or VoIP). DIDs allow direct routing of a call to a destination within the system. You can route to any destination available on the PBX.

Conferencing (Meet Me)

A Meet-me Conference is an extension on the system used for conference calls. Participants can access a conference by dialing the designated Meet-me Conference extension. Routing callers to a Meet-me Conference can be accomplished by using a DID, a menu, or simply transferring callers to the conference extension.

2011 Copyright  IPitomy Communication, LLC

3 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

FollowMe

This feature allows the PBX to try and find users who are not at their desk. It can be configured to call their cell phones, house phones, or other extensions in the PBX. Once answered, the user can accept the call, or refuse it. Unhandled calls return to the PBX to leave a message at the original extension’s voicemail.

Forwarding Gateway

Mobility has become a part of everyday life for most people. System users need to be able to take calls anywhere. The IPitomy IP PBX has the ability to forward calls. Users can turn call forwarding “on” and “off” while in the office or away from the office by using a touchtone key pad. This is set up in the edit Extensions page, but can be modified from any phone, including a cell phone. Modifying forward settings remotely requires the automated attendant (Menus) option to be programmed.

Cascading Message Notification

This feature works using the same methods as FollowMe, but pertains to voicemail messages. When configured, if an extension gets a new voicemail, you will be able to send the voicemail message to a variety of numbers (Destinations), define the order in which to send the message and can be set to make the system to notify you that a new message was received. Additionally, you can add or remove extensions to the list of recipients when a broadcast message is sent.

Voicemail Gateway

Using either a Menu or a DID, users can call in from any telephone and check messages. The voicemail gateway allows users to dial a pre-defined digit from a touch- tone key pad on any phone to retrieve their messages.

Branch Offices

Branch offices can be created to allow multiple PBXs to route calls to each other. Branch office extensions can be transferred to, placed in ring groups, or selected as menu destinations. Table 1 – IP PBX Features

2011 Copyright  IPitomy Communication, LLC

4 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

GETTING STARTED Boot Up – Safe Power Down Each IPitomy IP PBX is equipped with a Boot Up/Safe Power Down momentary switch at the front of the chassis. This switch is a primary element of controlling not only the hardware but the Operating System (OS) and PBX software. If it becomes necessary to use this switch – especially when powering down – it is imperative that you read and understand the functionality of this switch.

IMPORTANT:

!

Use of this switch is very convenient and VERY specific.

Improper use can cause very undesirable results.

Use this switch by pressing the elevated side and releasing immediately. 1100

1200

2000/5000

Behind Drive Access Door The switch has three functions: rd

(Use 1 & 2 only – unless directed to use the 3 function by a technical support representative). Repeatedly turning off the power with a hard boot can damage (corrupt) the data on the hard drive. In some instances, this can void the warranty.

Use 1.

Condition

Operation

While the PBX is not operating… (power cord connected but not yet powered up OR previously, properly powered down) While the PBX is operating…

2.

3.

Shut down can take as long as 5 minutes. Please be patient. While the PBX is NON-Responsive and all other methods to regain control of the OS and applications have failed.

2011 Copyright  IPitomy Communication, LLC

Press and release the switch to start PBX operation Press AND Release the switch to initiate the safe power-down sequence. The PBX will shut-down all applications running in the proper sequence – ensuring that no damage occurs to the database and applications during shut-down. Press AND Hold the switch to FORCE immediate shut-down.

This is NOT recommended and should be avoided.

5 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Connecting the System Hardware Setup The IPitomy IP PBX comes assembled and ready to install. The system requires some form of trunking, be it a connection to the PSTN for analog or T1 lines or a SIP trunk. It requires telephones to be connected to the local area network (LAN). Broadband access must be established for VoIP connectivity (allowing remote extensions , branch offices, remote management, and SIP trunks).

Figure 2 – Hardware Setup Diagram

Connecting the Phone Lines The IPitomy IP PBX is equipped to support analog, digital, gateway or SIP connections. Analog lines or a T1/PRI are connected with internal hardware resources. A gateway connects analog telephone lines by registering itself as a SIP provider over the LAN. SIP providers create a direct connection to the system.

INTERNAL ANALOG LINE CARDS The IPitomy IP PBX uses three basic analog devices for PSTN connectivity.

Digium TDM04B Analog Line Card (4 PSTN line connections) − This analog line card supporting these connections is already installed and completely configured. Simply connect the phone lines to the RJ11 jacks at the rear of the IPitomy IP PBX and start making calls.

Digium TDM808B Analog Line Card (8 PSTN line connections) − This analog line card supporting these connections is already installed and completely configured. Simply connect the phone lines to the RJ11 jacks at the rear of the IPitomy IP PBX and start making calls. !

IMPORTANT: The 4 and 8 PSTN line connections are a single pair, one line per jack. It may be necessary to echo tune the system. Please contact an IPitomy Technical Support personnel if you notice an echo on the line.

2011 Copyright  IPitomy Communication, LLC

6 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide Digium 2404B 16 and 2406B 24 Analog Line Cards (16 or 24 PSTN line connections) − These lines are plugged into an Amphenol connector and need to be terminated in a cross connect, break-out box or patch panel. The Amphenol connector uses a single pair connection to each phone line.

(Diagram 4)

INTERNAL DIGITAL T1 CARDS The IPitomy IP PBX uses two devises for digital connectivity.

Digium TE122P T1 Card (a single T1/E1/J1 connection) − This card supports industry standard telephony and data protocols, including both RBS and Primary Rate ISDN (PRI) protocol families for voice traffic. The card has a default configuration for the system, but this configuration may be adjusted based on preference. Plug the RJ45 connector into the T1 TDM source supplied by the T1 provider. Digium TE205P T1 Card (a dual T1/E1/J1 connection) − This card supports industry standard telephony and data protocols, including both RBS and Primary Rate ISDN (PRI) protocol families for voice traffic. The card has a default configuration for the system, but this configuration may be adjusted based on preference. Plug up to two RJ45 connectors into the T1 TDM sources supplied by the T1 provider.

(Diagram 5)

Connecting Using an External Gateway Gateways connect legacy phone equipment (PBXs, ACDs, voicemail systems, etc.) to modern VoIP systems and services. IPitomy supports many different communications protocols from both the modern world of VoIP and from the legacy PSTN. This makes it a powerful tool for building gateways and protocol converters. PSTN lines can be connected to a Gateway device. The gateway device is connected to the LAN. The Gateway is then registered as a SIP provider in the system.

2011 Copyright  IPitomy Communication, LLC

7 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Figure 3 – External Gateway Connection Diagram

Connecting to a LAN In order to be able to connect all of the devices (PCs, Phones, Gateways, etc) to their Local Area Network (LAN) you will most likely need to install at least one Switch.

Connecting Using SIP Providers Once connected to the LAN, the LAN's broadband connection provides a pathway for SIP VoIP Providers. Use the SIP Provider pages to setup a connection.

Figure 4 – SIP Provider Connection Diagram 2011 Copyright  IPitomy Communication, LLC

8 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Figure 5 – LAN Connection Diagram

Connecting Telephones The following diagrams indicate the port locations on the IP120 and IP1500. DC 5volt port

LAN Port

PC Port

DC 12volt port Handset Port

LAN Port

PC Port

Figure 6 – IP120 and IP1500 Connector Ports

2011 Copyright  IPitomy Communication, LLC

9 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

DATA AND NETWORK CONFIGURATION Planning before getting started will make the setup and installation of the IPitomy IP PBX simple. IPitomy has created the IPitomy Setup Worksheet to assist in recording business and system information used in planning system setup and installation. This Checklist can be downloaded from IPitomy.com in the Dealer Section of the Website. !

IMPORTANT: Please contact your IPitomy Sales Representative to obtain a login information for the Dealer site at (941) 306-2200.

Setup Worksheet The Setup Worksheet is broken out into sections where required data can be entered. Once all the information in the setup worksheet is populated, it can then be imported to the IPitomy system. This will save a great amount a setup/configuration time. !

IMPORTANT: To take full advantage of the functionality in the setup worksheet, you will need to make sure that your Excel macro security is set to Medium or lower (you will need to restart Excel after changing these settings). I

Figure 7 – Sample Setup Worksheet 2011 Copyright  IPitomy Communication, LLC

10 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide Data Type Network Information

Description/Recommended Settings You will need to know some basic information on the target network. Use this page to store all pertinent information regarding the sites LAN and WAN connection. • The type of data facilities you will be using for access to the Internet will dictate how much bandwidth is available for phone calls. • If you are going to use remote phones, SIP providers, or Branch Offices, you will need to have a fixed IP address.

User Data

Use this page to gather and store information for the extensions and stand alone mailboxes on the PBX. This page allows you to export the extension information to another worksheet. Save this worksheet as a .csv file and you can import it directly into the PBX, saving you time. • • •

Extension Numbers – required Name – required Email Address - required if the end user desires to use Unified Messaging



Device – setting this in the worksheet will make your installation much easier when using autoprovisioning and IP550/IP120 phones



MAC Address – for the most part this field can be left blank. If using Aastra phones, it may be more useful.

Voice mail only boxes may be created as well. You can print out a copy of this sheet and ask your customer to fill it in or provide them the spreadsheet to fill out. Groups

Use this page to gather and store information about ring groups. This will allow you to build the groups in the PBX much quicker at the time of install because everything has already been decided upon in advance.

Menus

Building menus in the PBX will be much easier once you have completed the sections pertaining to Menus. In addition to the setting in the PBX, you will be able to have the end user write out the prompt scripts, ensuring that the key press destinations match the dialogue the callers will hear.

Unified Messaging

Unified Messaging allows the PBX to send your voicemail messages directly to your email inbox. Use this section to log the end users email server information.

Telephone Lines

If you know the telephone numbers for your telephone lines, it is good to have them all documented ahead of time. You may want to route calls based on a particular number or specific DID.

Music On Hold

When a caller is place on hold, park, or is in Queue for a group of extensions, music may be played for them while they wait. The music on hold files can be uploaded to the system from your browser. The music on hold files need to be in MP3 format for IP1100+ systems, and 8bit 8Khz mono .wav file for the IP1000.

Licensing

Most IPitomy systems come default with a license for 16 users/extensions. To activate the initial license, you must have a connection to the internet and a license key will be uploaded to the system. This is a security feature that protects the user for warranty coverage as well as against unauthorized use. Filling out the User Data page will automatically tell you how many extensions the system needs, at a minimum, to handle the desired users.

Branch Office

This page will allow you to more accurately plan out an install that will have multiple sites connected via Branch Office. Using unique numbering for each PBX will allow for easier calling between sites. The lightning bolt, found on the User Data section of the Setup Worksheet, accesses a macro that allows you to export the User Data information pertaining to extension to another worksheet. Once exported, you can save that worksheet as a .csv file, and then load it directly into the PBX. Table 2 – Setup Worksheet Descriptions

2011 Copyright  IPitomy Communication, LLC

11 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Table 3 – Sample Exported .CSV Worksheet

CSV Upload Once all the extension information has been exported to a .CSV file, you can import that file into the PBX.

STEPS: 1

Navigate in the PBX to Destinations

Extensions. The Extensions page appears.

2

Select the BROWSE button at the top of the page. The File Upload window appears. Locate and select the file that you want to import then click the OPEN button.

Figure 8 – View of Upload Location Window 3

The CSV File field is updated with the source directory information for the file to be imported.

4

Click the IMPORT button. The Create Extensions page appears displaying the information that is going to be imported.

5

Review the information then select the CREATE button when you are done.

2011 Copyright  IPitomy Communication, LLC

12 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Figure 9 – Create Extension Results Page

6

The Create Extensions page will display the results of your import for each extension. You should see a “SUCCESS” message.

7

Click on the Return to Extensions link that appears on the page. This brings you back to the Create Extensions page. Review the Extensions List and find the extension (s) you just created.

8

Click on the Apply Changes link at the top of the page to make these changes live on the PBX. A message “Settings Applied” will appear.

9

You are now ready to update the various settings for the new extension. (See the Destination Extensions section of this user guide for more details on Extensions).

Network Requirements Making preparations for the network in advance will assure there are no surprises. If you are going to have remote extensions, you will need access to the router to setup a network address translation (NAT) and port forwarding. A LAN with a broadband connection is required for operation of the system. It must be on a fast Ethernet (100baseT or better). The system must also use Ethernet data switches. The router can use DHCP or not, depending on preference. The IPitomy IP PBX requires a fixed IP on the router subnet. Several ports may need to be forwarded. Make sure your router has TCP/IP port range forwarding by checking the box or product guide. The router should have a fixed IP address with a public IP. Pre-existing TFTP servers or DHCP servers broadcasting TFTP servers may cause conflicts for phone configuration. If you have a pre-existing TFTP server being broadcast by your DHCP server, please contact IPitomy support to determine the best solution.

2011 Copyright  IPitomy Communication, LLC

13 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Port Forwarding The following table outlines the port forwarding information in the router that maps public IP addresses to internal IP addresses. Port forwarding must be configured to utilize features such as remote phones, SIP Providers, remote administration and branch office. IPitomy port forwarding requirements are specified below.

Figure 10 – Port Forwarding Configuration Table

!

IMPORTANT: Please contact an IPitomy Technical Support Representative for assistance or additional information regarding how to configure port forwarding for the IP PBX system.

2011 Copyright  IPitomy Communication, LLC

14 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

IP Addresses To determine the IP address that can be used on the network, check the router or get this information from the Network Administrator. In many cases, this default IP address will be acceptable without any router configuration other than port forwarding (required for remote administration and remote telephones).

!

IMPORTANT: The IP PBX is required to have a fixed (static) IP address. The system comes with a default static IP address of 192.168.1.249/ippbx. We recommend that you use this default IP address. Please contact IPitomy’s Technical Support Group if you need further assistance by email at [email protected] or phone 941-306-2200 option2, or visit our FAQ page at our website at www.ipitomy.com.

Changing the IP Address If the default IP address does not match the network schema for your install, the PBX has a simple method for changing this information. The Network Console allows you to view and change settings without requiring an external web browser or any network connection.

STEPS: 1

Plug a keyboard and monitor into the IP PBX.

2

From this keyboard, press CTRL-ALT-F7

3

Follow the instructions displayed on the page to configure the IPs for the PBX. The options used are as follows.

4



1: Network Type – Static or DHCP



2: IP address



3: Subnet Mask



4: Default Gateway



5: Static DNS



6: Static DNS 2



7: Static DNS 3



R: Refresh View



D: Default Settings



S: Save & Update

Once all values have been configured to match the install network, choose S to save and update.

Note: For further details on using the Net Console, please refer to Appendix 6.

2011 Copyright  IPitomy Communication, LLC

15 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Figure 11 – Typical Network Configuration Diagram

Service Providers In order to provision the IPitomy IP PBX it is necessary to know the type of Service Providers being used. Carrier and SIP are the most common service providers. Carriers provide plain old telephone lines (POTS), T1s and PRI lines. SIP Providers route voice calls over the internet. This is called voice over internet protocol or VoIP. As part of the installation it will be important to know the: •

Name of Providers



Type of Service Provided (i.e., POTS, T1,or SIP)



Phone Numbers Associated with the Service



Password and Login Information for SIP Service

You should always consider any previous historical data that you have from your existing system. Any past reports or spreadsheets which relate to the components being designed, should be considered as possible input when configuring your IP PBX system. We recommended that you record this information on the IPitomy Setup Worksheet.

2011 Copyright  IPitomy Communication, LLC

16 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

SYSTEM ADMINISTRATION Administration Menu IPitomy IP PBX’s online administration makes it simple to meet the demands of a frequently changing business. It is also designed to be quick to setup and install. The Administration Menu is located in the Navigation Bar to the left of the page.

Figure 12 – Administration Menu Options

IP PBX Administration Options This menu contains the administration pages used to configure the system. The Administration Menu is divided into six sections. To navigate to an Administration Page click on the menu section and page to be changed.

System − System setup consists of network configuration settings. Providers − Providers are sources of PSTN and VoIP connectivity. Providers are the lines that handle all incoming and outgoing calls. All VoIP providers will be setup here. DID numbers are also entered here. Destinations − Destinations are extensions, groups of extensions, automated attendants (menus), conferences and voicemail. Destinations are places where calls get routed to in the system. Call Routing − Routing sends callers to specific inbound destinations within the system, and routing outbound callers over specific outbound routes like local, long distance, international and emergency. PBX Setup − System settings allow global configuration settings for system applications like PBX timers, voice messaging settings and music-on-hold. Reporting − The system displays usage reports, diagnostic information and monitors system activity.

2011 Copyright  IPitomy Communication, LLC

17 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide Administration Page Layout Each online Administration web page contains the standard layout. The following section describes the features or links you will have access to on each page. Logout / Apply Changes

Title Bar

Default Values

Advanced Features

About Us / Contact Us

Figure 13 – Standard Page Layout and Features

Link

Description

Title Bar

The Title Bar at the top of each page displays the name of the section of the Administration Menu which is currently being edited.

Default Values

When the system is installed it automatically registers default values in many of the administration fields. This simplifies the implementation process.

Advanced Link

In several of the online administration features there is an Advanced link where the most sophisticated capabilities of the IPitomy IP PBX can be configured. If available (depending on applicable functions), the Advanced link will be located on the lower left side of each page.

About Us Link

The About Us link is located at the bottom left corner of each page This link provides additional information about IPitomy.

Contact Us Link

The Contact Us link is located at the bottom left corner of each page. This link will take you to the Contact Us page that provides you with important contact information for IPitomy Communications, LLC. The IPitomy team is never more than a call or email away. To contact an IPitomy team member, click on Contact Us in the lower left corner of the page.

Apply Changes

To apply changes to the system you must click the Apply Changes button. Located in the top right corner of the page, this link globally applies changes to the system which is different than the Save Changes button that only saves changes to the current page.

Logout

The Logout link located at the top right corner of the page allows you to logout of the Administration page and takes you back to the IP PBX Admin Login page. Table 4 – Feature and Link Descriptions

2011 Copyright  IPitomy Communication, LLC

18 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide Navigational Tools The following section describes the navigation tools (buttons) that will allow you to perform various functions such as Add, Delete, Save or Update data within the Administration system. These buttons will appear where the functions are applicable to the type of data being created or modified.

Note: Depending on the page that is being displayed, the buttons/icons may be referred to (labeled) differently. This list describes the more commonly seen and used buttons/icons. Button/Icons

Description This button or icon allows you to expand or open the function to view more options. This button or icon allows you to collapse or close the function. This button or icon allows you to view the items from a drop down list. This checkbox button or icon allows you to select or deselect the record for viewing or modifying, as well as to define if certain features are enabled. This radio button or icon allows you to select or deselect (toggle) between options. This pencil icon allows you to edit the current settings for a specific record (i.e. extensions or groups). This pencil with a phone icon allows you to edit an extension’s current phone settings. This down arrow icon allows you to download a file off of the system. This “X” icon allows you to delete the item selected This curved arrow icon allows you to restore a file to the system or in some cases, clear out voice messages. The Add button allows you to create a new destination, provider, route, schedule, etc. For example, to add a new extension, click the Add button on the Extension Administration page. In some cases, the Add button will change (have a different label) depending on the function or page you are viewing or updating. For instance, the button may be displayed as the Menus page.

, if you are on

Located in the bottom left corner of the screen, the Save Changes button executes all the changes made to the current page. This button must be pressed before leaving a page or changes will be lost. Table 5 – Navigational Buttons and Links

An easy way to get the information that is required for a specific parameter or field is to mouse over it. A callout box with a description of the requirements or recommended settings will appear.

Figure 14 – View of Mouse Over Field Information

2011 Copyright  IPitomy Communication, LLC

19 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide Login Page

Figure 15 – IP PBX ADMIN Login Page

Logging In

STEPS: 1 From a web browser (ie. Firefox), enter the IP Address of the System Administration site. 2

Using the Admin Login (left side), enter the username and password of the PBX. The default login information is: Username = pbxadmin Password = ipitomy

!

3

IMPORTANT: Please contact IPitomy’s Technical Support Group if you need further assistance by email at [email protected] or phone 941-306-2200 option 2. You can also visit our FAQ page at faq.ipitomy.com.

The PBX Administration screen appears. Now you can navigate around the PBX, configuring different features as needed.

Logging Out

STEPS: 1

You can logout of the PBX Administration page at anytime by clicking on the Logout link located on the top right corner of the screen.

2

The system logs out and returns you to the PBX Administration Login page.

2011 Copyright  IPitomy Communication, LLC

20 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

SYSTEM NETWORKING The IPitomy System Menu is for configuring network attributes. For example the IP address of the system and router information. The System Networking Setup Page allows you to define the Internet Setup for the system’s hardware. The system must operate using a static IP address; DHCP should only be used on the IPitomy IP PBX if the router is configured to assign a specific static DHCP address to the system.

Figure 16 – Networking Setup Page

The following table describes the fields and recommended settings for Networking Setup for the IP PBX system: Field

Recommended Settings

IP Address

Use the default address (192.168.1.249) of the IPitomy IP PBX or an address outside the range of existing IP addresses assigned by DHCP in the router.

Subnet Mask

Leave the default setting for the Subnet Mask as (255.255.255.0). The subnet mask defines what traffic the PBX will listen and communicate to. A value of 255 means the octet in question needs to match exactly, while a value of 0 means the octet is not restricted at all. When the PBX is set to the default IP address, a subnet mask of 255.255.255.0 tells the system to communicate with any devices in the 192.168.1.xxx range.

Default Gateway

The default gateway provided is 192.168.1.1. Though this default is a common router IP, every network is different. Enter the IP address of the router handling their Internet connection here.

Static DNS

Enter the DNS IP address being used on the network. If a default DNS IP address is not provided by the router it can be obtained from the network’s Internet Service Provider.

Static DNS2

Enter the DNS IP address being used on the network. If a default DNS IP address is not provided by the router it can be obtained from the network’s Internet Service Provider.

2011 Copyright  IPitomy Communication, LLC

21 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide Static DNS3

Enter the DNS IP address being used on the network. If a default DNS IP address is not provided by the router it can be obtained from the network’s Internet Service Provider. Table 6 – Network Setting Descriptions

TCP/IP Settings Section Edit TCP/IP Default Settings STEPS: 1

Navigate to System Networking. The TCP/IP Settings page appears displaying the default values for the following setting: • • • •

IP Address Subnet Mask Default Gateway Static DNS

2

Click on the IP Address field. Enter the IP address for the Router. Use the default address (192.168.1.249) of the IPitomy IP PBX or an address outside the range of existing IP addresses assigned by DHCP in the router Enter the desired IP Address. See Table above for recommended settings.

3

Click on the Subnet Mask field. Leave the default setting for the Subnet Mask as (255.255.255.0). See Table above for recommended settings.

4

Click on the Default Gateway field. Change the default Gateway value to the desired target network. See Table above for recommended settings.

5

Click on the Static DNS field. Change the default DNS value to the desired target network. See Table above for recommended settings.

6

Repeat step 5 to set the remaining DNS values, if necessary.

7

Click on the

8

Click the Apply Changes link located on the right hand corner of the page, to commit the changes to the database.

button

Access Control (PBX Access) The Access Control page is comprised of 3 sub-pages; Host Access, Web Server, and Access Control List. Each is accessible from the buttons at the top of the page and pertains a different method of controlling access to the PBX.

Host Access This feature allows you to limit access to special services on the PBX. An “allow from” entry is a list of one or more host names, host addresses, patterns or wildcards that will be matched against the client host name or address. List elements should be separated by blanks and/or commas.

2011 Copyright  IPitomy Communication, LLC

22 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide Note: The parameter for the IP PBX Host Access is pre-configured per the manufacturer’s specifications. We recommend that you do not change this configuration value.

Figure 17 – PBX Host Access Page

The following table describes the features and functions available on the Host Access page: Fields/Buttons

Description

Delete Selected Items

This button allows you to delete multiple services at a time.

Load Factory Defaults

This button will set the PBX back to the default Host Access settings.

Add a New Item

This section is where you would add new rules for accessing special services on the PBX Table 7 – Network Features and Descriptions !

IMPORTANT: Changes to the Host Access List are installed immediately. They are database independent so custom changes do not migrate from one box to another via a database backup file. Please contact IPitomy’s Technical Support Group if you think you need to modify these settings. Email via [email protected] or phone at 941-306-2200 option 2. You can also visit our FAQ page at faq.ipitomy.com.

Web Server Configuration This feature allows you to define which IPs and/or domains can access the web server, as well as restart the Web Server. In order for changes to this list to take effect, you must Restart the Web Server.

2011 Copyright  IPitomy Communication, LLC

23 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide The parameter for the IP PBX Web Server is pre-configured per the manufacturer’s specifications. We recommend that you do not change this configuration.

Figure 18 – Web Server Configuration Page

Feature Restart Web Server

Description This feature allows you to restart the web server so that changes made that impact server components can be applied. Note: Restarting the server will not interrupt phone service. A reboot of the PBX system will also apply changes made to other attributes.

Allow Access From

Delete Selected Items

Defines the networks and/or domains that are allowed to access the PBX. The “Allow” format may be: • Domain name • Full IP address • Partial IP address • Network / netmask pair • Network / CIDR specification This button allows you to delete multiple services at a time.

Load Factory Defaults

This button will set the PBX back to the default Web Server settings.

Add a New Item

This section is where you would add new rules for accessing the Web Server

2011 Copyright  IPitomy Communication, LLC

24 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide Table 8 – Web Server Features and Descriptions

!

IMPORTANT: Changes to the Web Server Access List are preconfigured. They are database independent so custom changes do not migrate from one box to another via a database backup file. Please contact IPitomy’s Technical Support Group if you think you need to modify these settings. Email via [email protected] or phone at 941-306-2200 option 2. You can also visit our FAQ page at faq.ipitomy.com.

Add New Permission STEPS: 1 2

Navigate to System  Access Control Click on the Web Server button located at the top of the page. The Web Server Configuration page appears.

3

In the Add a New Item section, enter the network or domain you want to allow to access the PBX web server

4

Click the ADD button.

5

The new permission rule will be displayed under Allow Access From window above

6 7

Click on the Restart Web Server button. Click OK when prompted to confirm you wish to restart the Web Server

8

A “Please Standby” message appears. Once the reboot process is completed you will be returned to the Web Server Configuration page.

Load Factory Default This feature allows you to restore the manufacturer’s factory default settings. It will restore the settings to the factory recommended defaults.

STEPS: 1

From the Web Server page, click Load Factory Default button. This will return or restores the Allow Access From list back to the manufacturer’s default setting.

2

Once the changes applied, you will need to restart the web server. Please refer to the Restart Web Server topic of this user guide for steps on how to restart the server.

3 4

Click on the Restart Web Server button. Click OK when prompted to confirm you wish to restart the Web Server

2011 Copyright  IPitomy Communication, LLC

25 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

5

A “Please Standby” message appears. Once the reboot process is completed you will be returned to the Web Server Configuration page.

2011 Copyright  IPitomy Communication, LLC

26 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Access Control List The Access Control List defines what networks different PBX features are permitted to communicate with.

2011 Copyright  IPitomy Communication, LLC

27 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Figure 19 – Access Control List - Add New Rule Section

The following table outlines the parameters and descriptions for the Access Control List.

2011 Copyright  IPitomy Communication, LLC

28 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide Feature

Description

Service

Displays the name of configured services. Typical services on the PBX are: SIP - Used for Calls Call Manager - Used for Desktop Call Manager TFTP – Used by phones to pull down config and firmware files

Ports

Displays the ports that were defined for a particular service. SIP – 5060 Call Manager – 5048 TFTP - 69

Rules

Displays the rules that were configured for a particular service. Deny List – Accepts all traffic, unless specifically defined Allow List – Denies all traffic, unless specifically defined Table 9 – Access Control List Definitions

Load Recommended Default This is the recommended method to set the Access Control List to the typically used settings.

STEPS: 1 2 3

4

Navigate to PBX SetupSIP Set the LocalNet to match the network the PBX is installed on, Save, and Apply Changes Navigate to the Access Control List page, click Load Recommended Default button. This will create default rules allowing the PBX to communicate to devices on the LocalNet in regards to SIP, Call Manager, and TFTP Click the Apply Changes link located on the right hand corner of the page, to commit the changes to the database.

Add New Service

Figure 20 – Access Control List Page - Add New Service Section

2011 Copyright  IPitomy Communication, LLC

29 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide The following table outlines the parameters and descriptions required for adding a new service. Feature

Description

Service Name

This is the name of the new service and will populate the Service drop-down list in the Add New Rule section.

Service Transport

This is the service type that will be used to transport the message. The options are Both, TCP or UDP. SIP and RTP traffic both occur on UDP, TFTP traffic is UDP, and Call Manager traffic is TCP. Any other rules created would need to be configured for the protocol used by this service.

Service Ports

This is the port information that is associated with the host. You can enter a single or range of ports that will be used for this service. SIP uses 5060, Call Manager uses 5048, and TFTP uses 69. Other services must be configured to use the appropriate ports.

Service Policy

This is the umbrella rule for the service, which will be further defined under Add New Rules. The options are: Deny List; ACCEPT ALL EXCEPT rule will apply. This will allow all traffic on the defined port, allowing you to configure a list of Denied IP addresses. Allow List: DROP ALL EXCEPT rule will apply. This will block all traffic on the defined port, allowing you to configure a list of Allowed IP addresses. Table 10 – Add New Service Settings and Descriptions

The following outlines the steps to add a new service in the PBX system.

STEPS: 1

Navigate to SystemAccess Control

2

Click on the Access Control List button, The Access Control List page appears.

3

From the Add New Service section, enter a Name, and select the appropriate Transport Protocol, Ports, and Policy; then click the Create Service button.

4

The new service and its associated values will be displayed in the Service listing.

5

Click the Apply Changes link located on the right hand corner of the page, to commit the changes to the database.

The following table outlines the parameters and descriptions required for adding a new rule. Feature

Description

Service

This drop-down list is populated when a new services is added. This is done in the Add New Service section.

Host(s)

This is the IP Address, Domain Name or URL of the host. Table 11 – Add New Rule Settings and Descriptions

2011 Copyright  IPitomy Communication, LLC

30 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide Add New Rule The following outlines the steps to add a new rule for Services in the PBX system.

STEPS: 1

Navigate to SystemAccess Control, click on the Access Control List button, the Access Control List appears.

2

From the Add New Rule section, select the Service type from the drop-down list.

3

Enter the Host/s to be allowed/denied by the service

4

Click the Create Rule button.

5

The new rule is added and will be displayed in the rules list.

6

Click the Apply Changes link located on the right hand corner of the page, to commit the changes to the database. .

Delete Rules or Services The following outlines the steps to delete existing rules or services.

STEPS: 1

From the Service section of the PBX Access – Access Control List page, find the service or rule that you want to delete.

2

icon to the left of either the service or rule. The selected item is removed Click on from the list.

3

Click the Apply Changes link located on the right hand corner of the page, to commit the changes to the database.

PROVIDERS Providers are telephone lines, VoIP providers and other telecommunication resources. This section of the system’s online administration is where these provider resources are configured. The PBX system is equipped to handle two types of provider setting’s Hardware Trunks and SIP Providers.

Hardware Trunks Hardware trunks are associated with telephone lines that connect to the PSTN. These lines process inbound and outbound communication traffic that flows over communication channels. For example, a T1 can be a trunk resource that has multiple lines and multiple Direct Inward Dialed (DID) numbers. These individual numbers can be routed to different destinations within the system.

Connection Types The IP PBX is equipped to support an assortment of hardware cards as discussed earlier. Depending on which card you have, the PBX can integrate with analog lines, T1, or PRI. 2011 Copyright  IPitomy Communication, LLC

31 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Provisioning a New Hardware Trunk Group Provisioning a hardware trunk defines how the system works with the provider equipment, tells the system what phone numbers are associated with the trunk, and establishes rules for the system to follow when processing incoming and outgoing calls through this physical network connection.

Figure 21 – Hardware Providers Trunk Setup Page

2011 Copyright  IPitomy Communication, LLC

32 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide The following table describes the fields and functions available on the Hardware Trunks Provider Configuration page. Section

Description Configuration Section

Slot

Defines which physical PCI slot the card is connected to.

Channels

This indicates whether the card has channels configured. Using the mouse to hover over this field will provide you with the number of channels at are set for this card.

Model

This is the model or type of card. This button changes the card set in the database for the adjacent slot. The change is immediate and will delete trunks associated with another card in the same slot. Selecting this button will take you to the Channel Group Parameters Card Configuration page, where you can create a channel group. Channel Groups Section

Name

The name associated with this channel group.

Channels

The number of channels that have been assigned.

Card

The card number associated with the channel group.

Action

- Clicking on the pencil icon allows you edit the settings for the selected channel group. - Clicking on the “X” icon allows you to delete/remove the selected channel group. NOTE: You must delete channels from outbound routes in order to delete them. T-1 Span Configuration

Span

Should automatically set to the appropriate span in regards to the cards that are installed in the PBX.

Timing

Set per your providers instructions, “0” (zero) would be the PBX provides timing, “1” would be the timing is provided by the Provider.

LBO

Line Build Out, set per your providers instructions.

Framing

Set per your provider’s instructions.

Coding

Set per your provider’s instructions.

PRI

Check if the trunk is a PRI, leave blank if the trunk is a standard T-1. T-1 PRI Configuration

Span

Should automatically set to the appropriate span in regards to the cards that are installed in the PBX.

Switch Type

Defines what type of equipment the PBX is communicating with. Set per your provider’s instructions.

Reset Interval

Set per your provider’s instructions.

Dialplan

Set per your provider’s instructions.

2011 Copyright  IPitomy Communication, LLC

33 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide Indication

Set per your provider’s instructions.

D Channel

Set to 24. USB Device Browser

Slot

Should automatically set to the appropriate slot that corresponds to the USB slot the device is connected to. Hardware Functions

Restart USB Devices & PBX Services

This button will restart USB devices and PBX Services.

Table 12 – Hardware Trunk Provider Settings and Descriptions

The following section outlines how to setup the parameters for hardware trunks. Configuring Hardware Trunks

STEPS: 1

Navigate to ProvidersHardware Trunks. The Hardware Trunk (Providers) page appears. The hardware trunks and their values that have already been provisioned will be displayed.

2

The system will allow configuring of up to 2 cards that interface with analog or T-1 devices. Select the card models installed in your IP PBX individually and click Set button for each card in order to tell the system which cards you have.

3

Once you have set the card, click the Add Lines button to the right of the corresponding card to define line/channel/trunk groups associated with that card. The Edit Hardware Provider page appears.

2011 Copyright  IPitomy Communication, LLC

34 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Figure 22 – Add/Edit Hardware Provider Configuration Page

4

Edit the necessary parameters. Required fields are: Group Name, Signalling Type, Start Channel, and End Channel. The rest of the fields can be configured as needed, or left at their defaults. (refer to the table below for descriptions and recommended settings)

5 6

Click on the button. Click the Apply Changes link located on the right hand corner of the page to commit the changes to the database. Once the changes are applied, navigate to the Hardware Providers page and click the Restart USB and PBX Services button.

7

2011 Copyright  IPitomy Communication, LLC

35 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide The following table describes the fields and parameters available on the Add/Edit Hardware Provider Configuration page: Section/Field

Description

Channel Group Parameters Card 1 Group Name

This is the name for the groups of channels you want to create. This Group Name will be associated with the line/channel group. This is the type of signaling used for these channels/lines. Recommendation and default settings are listed below:

Signaling Type

Generate Ringing on Outbound Calls? Answer Incoming?

• Analog lines should be set to fxs_ks. • T-1 lines should be set to fxs_ls or em_w • T-1 PRI lines should be set to pri_cpe. This should only be checked if the telephone company is not providing ringing. Default this is disabled. This indicates whether the system should answer incoming calls on these lines/channels. The default value is Yes. Used to define the Start and End channel for this group on the associated card. If you would like a 1 channel group set the start and end channel to the same value (i.e. Start=1 and End=1).

Start & End Channel !

IMPORTANT: If you wish to address analog lines individually you must build multiple single channel groups. T1 and PRI can be grouped with multiple channels and routed via DID.

Allow Caller to transfer outbound call?

This indicates whether the system will allow user to transfer a call they origninated that has been connected to the PSTN. Default this is disabled.

Answer After

If the system is configured to answer incoming calls, this defines how many seconds to wait before answering the call. At times this field needs to be tweaked to ensure consistent CID. Default this is set to 0.

Dial Prefix

Digits defined here will be dialed out the trunk ahead of the digits dialed by the user. This would be required if your provider needs a 9 or some other digit to dial outbound. Analog trunks might need a one second pause which is denoted by a lowercase w. Default this is blank.

Allow Call Recording?

This setting toggles the ability to record calls on this trunk. Default this is disabled.

Ext CID Override?

This setting allows the users to set an alternate caller ID under their extension that will override the outgoing caller ID. If this is enabled, then this allows extension caller id override capabilities. Default this is disabled. !

IMPORTANT: Contact your provider to determine whether CID override is allowed on your specific trunk

Restrict CID Override?

This setting is used to limit an extension’s ability to override Caller ID (CID). If enabled, this allows extension CID Override only for the phone numbers defined for this provider. Default this is disabled.

Use Caller ID

This setting indicates whether the system should attempt to detect caller id on the lines/channels in this group. Default this is set to Yes.

2011 Copyright  IPitomy Communication, LLC

36 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide Echo Cancellation

This allows you to configure the Echo Cancel parameter. By default this is set to Yes (128) which will work in most scenarios. Adjustments can be made as needed.

RX Gain

This allows you to set or adjust the gain on sound received from these lines/channels. Typically these settings don’t need to be changed from default settings, unless there are issues relating to the volume on the calls. (This setting is in decibels so 3.0 = 100% increases in volume). Default this is set to 0.0.

TX Gain

This allows you to set or adjust the gain on sound transmitted to these lines/channels. Typically these settings don’t need to be changed from default settings, unless there are issues with the volume on the calls. (This setting is in decibles so 3.0 = 100% increases in volume). Default this is set to 0.0.

Inbound Caller ID

This is the name of the Caller ID of the inbound calls on this trunk. If set to the system default “asreceived', the calls will capture the Caller ID information sent over the incoming lines. Otherwise you can override the name and number that appears to those receiving calls on the corresponding channels. !

Echo Cancellation Bridged

Busy Detect

IMPORTANT: If you need to change this parameter, we recommend that you contact IPitomy’s Technical Support Group at (941) 306-2200 for the proper syntax or additional information.

This allows you to enable or disable the Echo Cancellation Bridge parameter on calls routed internally across the network. Set this parameter to”YES” (enable) if you want echo cancellation on calls that are bridged from one port to another on the network. Default this is set to No. By default, this is set to YES and 8. This allows you to enable/disable and set the number of busy signals the system will detect before disconnecting from the call (hanging up). Set the parameter to “YES” if you want the PBX to hang up after it detects a busy signal. The number field is the number of busy tones the system must detect before it disconnects from the call (hangs up).

Outbound Caller ID Name

Any values entered here will display as the Outbound CID Name when making calls out this trunk. If this is left blank, the name displayed on outbound calls will match what is registered with the provider. Blank by default. !

Outbound Caller ID Number

IMPORTANT: Contact your provider to determine whether CID override is allowed on your specific trunk

Any numbers entered here will display as the Outbound CID number when making calls out this trunk. If this is left blank, the number displayed on outbound calls will match what is registered with the provider. Blank by default. !

IMPORTANT: Contact your provider to determine whether CID override is allowed on your specific trunk

Echo Training

This parameter is used to adjust the time spent training the echo cancellation algorithm before a call is picked up. The length of time is set in milliseconds (ms), and is set to 800 by default.

Route Calls to

This is the default destination for the trunk. A destination is where calls from this provider will be routed to, unless a specific Direct Inward Dial (DID) is indicated. A typical destination is defined as a Menu, Extension, Schedule, Voicemail, or a Ring Group. This can also be set under the Incoming Routing page.

Relax DTMF

This allows you to turn On/Off the Relax DTMF detection. Enabling this setting

2011 Copyright  IPitomy Communication, LLC

37 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide (Detection)

allows the line/channels to be more permissive of tone lengths and result in over detecting. By default this is set to No. !

DTMF Tone Duration

IMPORTANT: We recommend that this parameter is set to NO unless you are having issues. Please contact IPitomy’s Technical Support Group for assistance or more information.

This allows you to set the DTMF tone duration in milliseconds (ms) for generated tones generated by calls bridged to SIP devices. Default value of 300. This allows you to enable/disable inbound routing and provides the dial plan that corresponds to the outbound routes in this Class of Service (CoS). This is Off by default.

Use Inbound CoS !

IMPORTANT: Use this only if you intend to provide PSTN connectivity to 3rd party equipment. Please contact IPitomy’s Technical Support Group for assistance or more information.

On a T1 or PRI, this is where you would configure any DID information. Only numbers or a + should be entered for a DID. Once configured, you can define a different inbound destination for each number, allowing you to route calls to separate places. Contact your provider to find out if they are sending 4, 7, or 10 digits inbound for the DID.

Phone Numbers

Table 13 – Hardware Provider Configuration Settings and Descriptions

Add Phone Numbers to Hardware Provider Once all the destinations are created, they will appear in a drop-down list and can be selected for updating.

STEPS: If a DID destination is set to NONE, it will route to the default location for the trunk itself.

1

From Channel Groups section of the Hardware Provider page, click the icon to the right of the name you want to modify. The Edit Hardware Providers page appears.

2

The hardware trunks and their values that have already been provisioned will be displayed. Scroll down the page to the Phone Numbers section. Enter the phone number that you want to add then click the ADD button. You can also copy and paste a list in. The list should be separated by newline characters.

3

The phone number entered will appear in the drop-down list to the right of the ADD button. The numbers will be listed in sequential order.

4

Click on the

5

Click the Apply Changes link located on the right hand corner of the page, to commit the changes to the database.

2011 Copyright  IPitomy Communication, LLC

button to save the changes to the system.

38 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Remove Phone Numbers from Hardware Provider

STEPS: 1

From Channel Groups section of the Hardware Provider page, click the icon to the right of the name you want to modify. The Edit Hardware Providers page appears.

2

Scroll down the page and click on the field to the left of the REMOVE button. Scroll through the drop-down list to find the phone number that you want to remove.

3

Click on the desired phone number. Click on the REMOVE button to the right of the list. The phone number is deleted and will not appear in the drop-down list.

Use the CTRL or SHIFT button to select multiple or a range of extensions from the list.

4

Click on the

5

Click the Apply Changes link located on the right hand corner of the page, to commit the changes to the database.

button to save the changes to the system.

Provisioning SIP Providers SIP Providers are VoIP service provider accounts or other SIP-based devices that provide PSTN connectivity. SIP provider accounts can have multiple phone numbers or Direct Inward Dialing numbers (DIDs). The individual numbers can be routed to different destinations within the system as DIDs.

!

IMPORTANT: SIP Providers settings vary widely. To simplify the provisioning process, we recommend that you ask the provider for a sample Asterisk configuration. Please contact IPitomy’s Technical Support Group for assistance.

Figure 23 – SIP Providers Configuration Main Page

2011 Copyright  IPitomy Communication, LLC

39 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Figure 24 – Add/Edit SIP Provider Configuration Page 1

2011 Copyright  IPitomy Communication, LLC

40 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Figure 25 – Add/Edit SIP Provider Configuration Page 2

2011 Copyright  IPitomy Communication, LLC

41 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide The following table describes the fields and functions available on the SIP Provider Configuration page: Sections/Fields

Description SIP Provider Section

Name

Name assigned to the SIP Provider. If given a username, this needs to match that field.

User Type

User type of the associated SIP Provider. This can be User, Friend, or Peer.

DTMF Mode

DTMF tone for the trunk. This can be Inband, rfc2833, info, or auto.

RFC2833 Compensate

This advanced feature is sometimes necessary when using RFC2833 is problematic or if the SIP provider has indicated that it is required.

Host

The domain or IP address associated with the SIP host.

Port

If your SIP provider requires registration on a port other than the default 5060, set this field to Custom and enter that port value; otherwise set to Default. NOTE: Be sure to forward this alternate port in your router or the traffic will not be passed through.

Registration option for the SIP Provider. Register



YES = Automatically generates based upon provided settings



NO = Doesn’t require authentication from the SIP Provider



CUSTOM =Allows for any special authentication rules required from the SIP Provider

Authentication (previously “Authorization”) requirements for the SIP Provider. Authentication



YES = Automatically generates based upon provided settings



NO = Doesn’t require authentication from the SIP Provider



CUSTOM =Allows for any special authentication rules required from the SIP Provider

Authorized User

Some providers require a different Authorization User Name than the Username provided. The sample asterisk configuration from your provider will let you know if this field needs to be set to Custom; otherwise set to Default.

From User

The sample asterisk configuration from your provider will let you know if this field needs to be set to Custom; otherwise set as Default.

From Domain

This parameter is rarely used and if needed, the SIP Domain information can be obtained from your SIP Provider

Realm

If your provider requires you to set the Realm to something other than asterisk, set to Custom and enter the realm given; otherwise this can be set to Default.

Outbound Proxy

Enable if the SIP Provider requires you to provide a different outbound IP address, otherwise leave as Default.

Username

Username used for Registration and Authentication.

Secret

The password used for SIP Registration and Authentication.

2011 Copyright  IPitomy Communication, LLC

42 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide Inbound Caller ID

This parameter should be left blank to display incoming caller ID as received. Otherwise you can override the name and number that appears to those receiving calls on the corresponding channels. !

IMPORTANT: If you need to configure the system in a different way, please contact IPitomy’s Technical Support Group for assistance and the proper syntax needed. Contact us via phone at 941-306-2200 option 2 or via email at [email protected] Additional information can be found at faq.ipitomy.com.

Outbound Caller ID Name

Enter an outbound Caller ID name that will override the Caller ID name that is displayed on outgoing calls through this provider. !

Outbound Caller ID Number

IMPORTANT: Contact your provider to determine whether CID override is allowed on your specific trunk

Enter the Caller ID number that will override on outgoing calls through this provider.. !

IMPORTANT: Contact your provider to determine whether CID override is allowed on your specific trunk

Call Limit

Set to match the number of concurrent calls allowed by the SIP trunk. (Usually consistent with SIP provider subscription limit.)

Qualify

This is the number of milliseconds (ms) the system should wait before checking to see if the SIP provider is available. Check with your provider to see what value this should be set to. Typically this can be left at the default value of 30000.

Default Destination

This is where all inbound calls will be routed to, unless a different specific destination is designated for DIDs on an individual basis.

Dial Prefix

Set this parameter only if the SIP Provider requires it.

Area Code

This parameter is obsolete and will be removed in future releases.

Generate Ringing On Outbound Calls

This parameter should only be enabled (checked) if ringing is not provided by the SIP Provider.

Allow Outbound Caller to transfer

Enabling this parameter allows a user to transfer a call that they originated on this trunk. Default is disabled.

Allow Call Recording

If enabled (checked), this parameter allows calls to be recorded.

Ext CID Override

If enabled (checked), this parameter allow the users to set an alternate caller ID under their extension that will override the outgoing Caller ID. Default is disabled. !

Restrict CID Override?

IMPORTANT: Contact your provider to determine whether CID override is allowed on your specific trunk

This setting is used to limit an extension’s ability to override Caller ID (CID). If enabled, this allows extension CID Override only for the phone numbers defined for this provider. Default this is disabled.

2011 Copyright  IPitomy Communication, LLC

43 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide This parameter allows a mechanism to reconnecting calls midstream.

Can Reinvite



YES = if the phone type allows the re-invite feature



NO = if the phone type does not allow the re-invite feature



N/A = accepts the system wide default defined under PBX Setup SIP  Advanced. If the default setting is acceptable and works within your business, we recommend leaving the parameter set to N/A.

Send Remote Party ID

Usually not required. Leave on “N/A” unless advised differently by tech support.

Trust Remote Party ID

Usually not required. Leave on “N/A” unless advised differently by tech support. This parameter allows you to specify how to handle connections with peers. Explanation of the different options available on the drop-down list are: •

PORT = Ignore the port number where authentication came from.



INVITE = Do not require the initial invite to authenticate.



PORT+INVITE = Do not require initial invite to authenticate and ignore the port where the request came from.



YES – To match a peer based by IP Address only and not the port.



VERY – To allow registered hosts to call without re-authenticating.

Insecure

Encodes a stream or signal for transmission. Select which codecs will be enabled for this provider. Can typically be left to defaults.

Allow Codecs

Phone Numbers Section

Phone Numbers

This is where you would configure any DID information. Only numbers or a + should be entered for a DID. Once configured, you can define a different inbound destination for each number, allowing you to route calls to separate places. Contact your provider to find out if they are sending 4, 7, or 10 digits inbound for the DID.

Table 14 – SIP Provider Configuration Settings and Descriptions

Add New SIP Provider The following section outlines the steps to add a new SIP Provider in the PBX system.

STEPS: 1

Click ProvidersSIP Providers. The SIP Providers page appears.

2

Click on the

3

Configure the pertinent fields per your SIP Providers instructions. See the table above for descriptions.

4

Click on the

5

Click the Apply Changes link located on the right hand corner of the page, to commit the changes to the database.

2011 Copyright  IPitomy Communication, LLC

button. The Edit SIP Provider page is displayed.

button.

44 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide Add Phone Numbers The following section outlines the steps to Add phone numbers to the SIP Provider.

STEPS: 1

Click ProvidersSIP Providers. The SIP Providers page appears.

2

From the SIP Providers page, select the SIP provider link (under the Name field) or the icon to the left of the provider you want to modify. The Edit SIP Providers page appears.

3

Scroll down to the Phone Numbers section of the page. Enter the phone number in the box above the ADD button then click ADD. The number enter will appear in the list to the right of the box.

4

To add multiple phone numbers at one time, press the ENTER key to move to the next space on the list then enter the number. Click on the ADD button and all the numbers will appear in the list box (on the right). You can also copy and paste a list in. The list should be separated by newline characters.

5

Click on the changes.

6

Click the Apply Changes link located on the right hand corner of the page, to commit the changes to the database.

button, once all the numbers have been added, to save the

Remove Phone Numbers The following section outlines the steps to remove phone numbers from the SIP Provider.

STEPS: 1

Click ProvidersSIP Providers. The SIP Providers page appears.

2

From the SIP Providers page, select the SIP provider link (under the Name field) or the icon to the left of the provider you want to modify. The Edit SIP Providers page appears.

3

Scroll down to the Phone Numbers section of the page. Select the number that you want to remove from the list then click the REMOVE button. The number enter will be deleted from the list.

4

To remove multiple phone numbers, hold down the SHIFT key to select the numbers in sequence or the CTRL key to select in random order. Click the REMOVE button to delete the numbers selected.

5

Click on the

6

Click the Apply Changes link located on the right hand corner of the page, to commit the changes to the database.

2011 Copyright  IPitomy Communication, LLC

button, to save the changes.

45 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide Set Destination The following section outlines the steps to set a Destination for DID phone numbers.

STEPS: 1

Click ProvidersSIP Providers. The SIP Providers page appears.

2

From the SIP Providers page, select the SIP provider link (under the Name field) or the icon to the left of the provider you want to modify. The Edit SIP Providers page appears.

3

Scroll down to the Phone Numbers section of the page. Select the number that you want to assign a destination. Select the desired Destination from the drop-down list then click the SET button.

4

To assign the same destination to multiple phone numbers, hold down the SHIFT key to select the numbers in sequence or the CTRL key to select in random order. Click the desired Destination from the drop-down list the click SET button. You can also set the destinations under Call Routing Outgoing.

5

Click on the

6

Click the Apply Changes link located on the right hand corner of the page, to commit the changes to the database.

button, to save the changes.

Delete SIP Provider The following section outlines the steps to DELETE a SIP Provider in the PBX system. !

IMPORTANT: You must remove all instances of the SIP provider from any outbound dialing routes before you can delete it.

STEPS: 1

Click ProvidersSIP Providers. The SIP Providers page appears.

2

From the SIP Providers page, icon to the left of the provider you want to delete. The SIP provider will be removed and will no longer appear on the list.

3

Click on the

4

Click the Apply Changes link located on the right hand corner of the page, to commit the changes to the database.

2011 Copyright  IPitomy Communication, LLC

button, to save the changes.

46 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

DESTINATIONS Destinations are the various places that a call can be routed to within the system. The destinations drop-down list is populated as destinations are added to the system. During system implementation, if destinations are populated first it is easier to provision the hardware trunks because all of the destinations will be available in the drop down menu. These system destinations should be obtained in advance to simplify the setup process. In most cases, there will be a menu to setup for an automated attendant. There will also be business hours to setup. We recommend that you use the IPitomy Setup Worksheet to help you gather and organize the necessary provisioning information prior to installation (see the figure below). The Setup Worksheet can be found on IPitomy’s website. (Please refer to the “Installation Worksheet” section of this user guide for details on how to use the Setup Worksheet).

Extensions

Groups Prompts

Menus

Schedules Providers

Call Routing

Figure 26 – IP PBX Data Components



Extensions: are individual extensions assigned to a telephone. When an extension is created, a voicemail box is also created. This voicemail box is automatically the destination for an extension call which exceeds its ring time.



Groups: are groups of extensions that can have different ringing strategies and can be routed from any trunk, another destination or dialed from an extension.



Menus: are used for creating automated attendant menus to route callers to different destinations within the system. The voice prompt can also be used to play information like driving directions.



Conference Rooms: allow multiple users to participate in the same call. Callers can be routed to a Conference via; direct dialing, through a DID, using an automated attendant or transferred by a person.



Voicemail Boxes: are where callers leave a message when someone is not available at an extension. Voicemail boxes that are created separate from extensions can be used to route callers after hours or as an overflow destination. Note that in the current implementation Voicemail Boxes without an extension cannot be dialed with only the voicemail box number. You

2011 Copyright  IPitomy Communication, LLC

47 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide can enter as one leaving a message by dialing *+ box number or you can check the messages by going through the voicemail gateway or dialing 924. •

Schedules: route callers to different destinations in the organization during specified times and dates.



Branch Office: connections provide broadband access to other branch locations by dialing a short access code followed by the extension number. Branch Extensions can also be defined as part of a branch office. These are remote extensions that can be dialed directly as though they were local extensions on your PBX. Branch Extensions also appear in drop down boxes for routing calls to specific destinations.

Extensions Extensions define where specific people or departments can be reached in an organization. They should be setup first in the system. The following is a list of the various settings/parameters that will can be updated for each extension. The parameters you configure for the extensions will vary based on the customer’s general business practices. • • • • • • •

General Settings Forwarding Settings Advanced Network Settings Advanced Voicemail Settings Advanced Allow Codecs Settings Advanced Calling Permissions Advanced Follow-Me

Add/Import Tab The Add/Import tab allows you to create new extensions or edit existing extensions.

Use the Setup Worksheet to upload the CSV file and automatically create the Extension information. Please refer to the Setup Worksheet section of this guide for details.

2011 Copyright  IPitomy Communication, LLC

48 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Figure 27 – Extensions Add/Import Page

Figure 28 – Create Extensions Page

2011 Copyright  IPitomy Communication, LLC

49 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide Sections/Fields

Description

Extension Name

This is the name of the person that the extension will be assigned to (using this device).

Email Address

This is the user’s email address (optional)

Ext. #

The extension number that is assigned to this device.

Device Type

This is the type of device that will be using this extension (i.e. IP550).

MAC

This is the MAC ID of the device (optional).

AutoNumber/Start At

Selecting this option allows you to automatically number the extensions that you need to add. To use this feature, simply enter the extension number you want to start with then select (place a checkmark) the AutoNumber option. Table 15 – Create Extension Fields and Descriptions

Add/Create Extensions This section describes in detail how to create a new extension.

STEPS: 1

From any page of the PBX Admin system, click on the button next to the Destinations link to expand the menu. The Destination menu opens and displays the options available.

2

Click on the Extensions link. The Extensions page opens and displays a listing of extensions (if ones already exists).

3

Click on the box to the left of the Extensions field. This value defaults to “10”. Enter the number of extensions you want to add and then click the ADD button.

4

The Create Extensions page appears displaying the number of rows that was specified. Enter information for the extension in these fields. See table above for details.

You can have the system automatically number the extensions you want to create by clicking the AutoNumber checkbox located on the top left hand corner of the Create Extensions page. 5

Click on the CREATE button when all the extension information you want to create is entered. The system responds with a message indicating the results of adding the new extension(s). You should see a “SUCCESS” message.

6

If there is an error, you will see an “ERROR” indicated under the Results field. An error is typically due to an extension number that is being duplicated (already existing in the system). Make the necessary adjustments to correct the error then click the CREATE button.

7

Click on the

8

Select the Apply Changes link located on the right hand corner of the page, to commit the changes to the database.

2011 Copyright  IPitomy Communication, LLC

button, to save the changes.

50 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Search Tab This tab allows the user to search the extensions for keywords in the fields: Class of Service, Departments, Name, Numbers, CID Names, CID Numbers, Email, or Status .This section describes in detail how to search for existing extensions.

Figure 29 – Search Extension Page The following table describes the types of search parameters the system will perform. Sections/Fields

Description

Class of Service

This is the class of service that is assigned to the extension(s).

Departments

This is the department that is assigned to the extension(s).

Names

This is the name of the user assigned to the extension(s).

Numbers

This is the extension number.

CID Names

The caller ID name that is associated with the extension(s).

CID Numbers

This is the caller ID number that is associated with the extension(s).

Emails

Email address that is associated with the extension(s).

Status

This is the status of the extension(s).

Match Search Filter

Exact – indicates that you want the search to match exactly as the search criteria that is entered. Partial – indicates that you want to partially match the search criteria entered.

Table 16 – Search Extension Parameters and Description

Search Extension This section describes how to search for extensions.

STEPS: 1

From the Extensions page, click the Search Tab. The list of extensions that are in the system appears with search options at the top section of the page.

2

Click the

drop-down arrow icon next to the Class of Service list.

Select the desired search criteria then enter the parameters in the box to the right of the list then click the Search button. If the system finds any extensions matching your search parameter, it will display the information in the extensions window.

2011 Copyright  IPitomy Communication, LLC

51 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide If the field is left blank, the system will bring all the extensions.

View Tab (Extensions) This tab allows the user to sort the display of extensions by Phone Model. Once sorted, phone key settings can be mass edited for phones of the same model. This section describes in detail how to view existing extensions.

Figure 30 – Extensions View Page

Edit or View Extension This section describes in detail how to view or edit extension details.

STEPS: 1

Navigate to the DestinationsExtensions page.

2

Select the or the icon to the right of the extension name you want to view or edit. The pencil edits the PBX settings and the pencil with the handset behind it edits the Phone settings.

3

The Edit Extensions page displays with setting details for the extension.

4

Make the necessary changes to the extension.

5

Click on the

6

Click the Apply Changes link located at the right hand corner of the top of the page, to commit the changes to the database.

button to save the changes.

You can edit multiple extensions by selecting (placing a checkmark in the box next to extension name). Only the fields being changed (that is common for all extensions selected) will be modified – i.e. Status or call group, etc.). Another shortcut that the system provides you is the Previous and Next button located on the top left corner of the Edit Extension page. Use these buttons to navigate backward or forward to find the extensions you want to view or modify. Mass Edit PBX Extension Settings This section describes in detail how to view or edit extension details.

STEPS: 1

From the DestinationsExtensions page, click on the View tab. A list of extensions appears.

You can sort the list by phone model by selecting (placing a checkmark) the Phone Model & Settings option located in the top left hand corner of the screen. 2011 Copyright  IPitomy Communication, LLC

52 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide If you are using this method, you can also Mass Edit Phone Key settings. See the section below for steps. 2

Select (place a checkmark) in the box next to the extension name(s) you want to view or edit.

3

Click on the Edit PBX Settings button. The extension details page appears. On the top left corner of the screen, you will see the extension numbers that you are viewing or editing.

4

Make the necessary changes to the extension settings then click on the button to save the changes.

5

Click the Apply Changes link located at the right hand corner of the top of the page, to commit the changes to the database.

Mass Edit Phone Key Settings This section of the Administration Guide describes how to mass edit the key settings for extensions using the same phone model.

Figure 31 - Extensions View Tab (Mass Edit Feature)

STEPS: 1 From the DestinationsExtensions page, click on the View tab. 2 Select the Phone Models and Settings option at the top left hand corner of the list. 3 The system will display a list of the extensions in a grouping of phone types. Select the group of phones you want to edit. A listing of all the extensions in the phone group will appear. 4 Select the box next to the name of the extensions you want to update or click on box next to the Name field at the top of the column to select all the extensions.

2011 Copyright  IPitomy Communication, LLC

53 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide 5 Click the Edit Phone Settings button. The system will take you to the Key Settings page for the phones. At the top of the page you will see a list of all the extensions that you are updating. 6 By default, the Only Save Changed Fields option Is selected, de-select if needed. 7 Once all the changes are made, select the Save and Restart Phone button to save changes and reboot the phones so they can pull down their updated configuration file.

Delete Extension This section describes in detail how to delete existing extensions.

STEPS: 1

Navigate to the DestinationsExtensions page

2

Select the

3

The extension is deleted and a confirmation message will appear. Click OK on the message window.

4

The system returns you to the Extensions page. The extension that was just deleted will no longer appear on the list of extensions.

5

Click the Apply Changes link located at the top right hand corner of the page, to commit the changes to the database.

icon to the right of the extension name you want to Delete

Delete Multiple Extension This section describes in detail how to delete multiple extensions.

STEPS: 1

Navigate to the DestinationsExtensions page

2

Select (place a checkmark) in the boxes next to the extension name(s) you want to delete.

3

Click on the Delete All button. The selected extension will be removed from the list and deleted from the database.

4

Click the Apply Changes link located at the top right hand corner of the page, to commit the changes to the database.

2011 Copyright  IPitomy Communication, LLC

54 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Extensions - General Settings Section Once the extensions have been added to the database, you can edit the settings for each of the extensions.

Figure 32 – Extensions General Settings Section

Sections/Fields

Description

Name

Name of the user associated with the extensions being created

Number

Extension number for this person or department. This must be 3 to 4 digits in length

Email

Email address for the person assigned to the extension. This will allow the system to forward email messages to the address of the person at the extension when properly configured.

Status

Active = currently in use Disabled = currently not in use

Class of Service

This is the service type for the extension. When initially created, the PBX will set this to the COS you have definined as the system default class of service on the PBX SetupGeneral Page

2011 Copyright  IPitomy Communication, LLC

55 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

PIN

This is the number used to access the extensions voicemail and can be between 1 and 6 digits long. The default setting is for the PIN to be the extension number. Be sure to instruct users to change the PIN to avoid unauthorized use.

Ring Time

This is the time in seconds that a call will ring before it is considered unanswered. Ring time must be between 1 and 100 seconds in length.

Call Group

This number assigns this extension to a group with a similar purpose (e.g., Sales or Customer Service). Multiple call groups can be assigned to each extension by putting a comma between the group numbers. The call groups also define which Pickup Groups can answer calls to this extension.

Pickup Group

This number should match any Call Group number entered on an extension. It defines the Call Group Numbers this extension can pickup remotely by pressing 99.

Apply Schedule

When an extension is created, a schedule destination is created automatically. This schedule is not activated until the Apply Schedule box is selected. When it is selected, all calls sent directly to this extension must first pass through the extension’s schedule and will be routed accordingly. Extension schedules will appear with the name of the extension (e.g., Extension 123 would appear as “ext_123”). (See the Schedules section of this guide for more information.)

CID Override

If enabled, the user will be able to override the Caller ID settings. When the user places a call, the original assigned CID will be bypassed and the name and number will that is entered in the CID Name and Number fields will be sent instead. Always check with your provider that CID override is allowed before configuring.

CID Name

If the CID Override parameter is enabled, this is the Caller ID name that will be seen by the recipient when an outbound call is placed. Always check with your provider that CID override is allowed before configuring.

CID Number

If the CID Override parameter is enabled, this is the Caller ID number that will be seen by the recipient when an outbound call is placed. Always check with your provider that CID override is allowed before configuring.

Detect Fax

If checked, calls from an Analog or T1/PRI card that route direct to this extension will spend a period of time (Defined under PBX SetupGeneral) checking if the call is a fax. During this time, the PBX holds the call; if fax tone is detected, the call will be passed along to the destination defined for Route Fax To, otherwise it will pass the call to the extension after the detection time has expired.

Route Fax To

Define where calls will be routed if fax tone is detected. Table 17 – General Extension Settings and Descriptions

2011 Copyright  IPitomy Communication, LLC

56 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Extensions - Forward Settings Section The extensions forwarding settings are made to be very user friendly. The settings may be modified from the Smart Personal Console, changed from your telephone extension, or changed remotely from any telephone (including cell phones), using the touch-tone key pad.

Figure 33 – Extensions Forward Settings Section

Forward settings routes calls to a different destination. These settings can be: Sections/Fields

Description

Unconditional

Always route calls to a specific destination.

Busy

Route calls to a specific destination when the extension is in use or do not disturb is enabled.

No Answer

Route calls to a specific destination when a call is not answered in the defined Ring Time

Unavailable

Route calls to a specific destination when a phone is turned off, is not registered with the system, or has reached its call limit (as set in the IPitomy IP PBX). Table 18 – Extension Forward Settings and Descriptions

2011 Copyright  IPitomy Communication, LLC

57 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Enable/Disable Forward Settings The following outlines steps to enable or disable forward settings:

STEPS: 1

Pick the setting to be modified – Unconditional, Busy, No Answer or Unavailable.

2

Select Enabled or Disabled. Disabled turns the forward setting off. Enabled turns the forward setting on.

3

Select either Phone Number or Destination. Phone Number allows you to enter the digits you want dialed, like a PSTN number. Destination will bring up the standard dropdown list of destinations in the system; Extensions, Groups, etc.

4

Enter the Phone Number or select the Destination you would like the PBX to route to when meeting the forwarding requirements.

5

Click

button to save the changes. The system returns you to the Edit

Extensions page. 6

Click the Apply Changes link located on the right hand corner of the page, to commit the changes to the database.

Change Unconditional Forwarding via Keypad

STEPS: Only unconditional forwarding can be changed from a touch-tone keypad. Enter the following code to set the unconditional forwarding setting. 1

Dial *90 to disable forwarding.

2

Dial *91 to enable forwarding.

3

Dial *92 to set the forwarding number.

2011 Copyright  IPitomy Communication, LLC

58 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Change Unconditional Forwarding via PC The following outlines the steps for the end user to change the extension forwarding setting from a PC using the Smart Personal Console. The administrator will need to have enabled Allow User to control Forwarding under the extensions calling permissions.

STEPS: 1

Browse the internet to the Smart Personal Console page.

2

Login.

3

Click the

4

Enable/Disable the desired forwarding setting.

5

Select either Phone Number or Destination. Phone Number allows you to enter the digits you want dialed, like a PSTN number. Destination will bring up the standard dropdown list of destinations in the system; Extensions, Groups, etc. Enter the Phone Number or select the Destination you would like the PBX to route to when meeting the forwarding requirements.

6

7

Click

link to access the forwarding page.

button to save the changes

Change Forwarding Number While Away from an Extension Only unconditional forwarding can be changed from a touch-tone keypad.

STEPS: 1

Call into the Automated Attendant (menu).

2

Select the touch-tone digit that routes to the Forwarding Gateway.

3

The system will prompt for an Extension Number and Password.

4

The system will indicate if extension forwarding is Enabled or Disabled.

5

Pressing “1” toggles between Enabled and Disabled.

6

Pressing “2” allows the forwarding destination to be modified.

2011 Copyright  IPitomy Communication, LLC

59 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Extensions - Advanced Settings Extensions - Network Settings Section Network settings automatically register in the extension through the system. These settings represent registration and identification information. The system (extension) defaults should not be changed without advanced knowledge of the behaviors of the particular settings.

Figure 34 – Extensions Advanced Network Settings Page

2011 Copyright  IPitomy Communication, LLC

60 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Sections/Fields

Description

SIP Password

Password for the user to access IP PBX web-based administration system. Use a combination of uppercase letters, lowercase letters, and numbers.

Generate

If clicked, the system will automatically generate a password for the extension. This color code bar indicates the strength of the password being assigned for the extension. The strengths are represented with the following colors:

Password Strength

Location

This allows the user to tell the PBX whether to expect this extension to register as a local extension (LAN) or as a remote extension (WAN).

NAT

HOST

!

IMPORTANT: This setting should be ENABLED (checked) unless otherwise instructed. Please contact an IPitomy’s Technical Support Group for assistance or more information.

!

IMPORTANT: This should be set to DYNAMIC unless otherwise instructed. Please contact IPitomy’s Technical Support Group for assistance.

Phone Type

The phone type is a drop down list for selecting which IP phone hardware is being used on the extension. IPitomy supports Aastra phones as well as our own IP550 and IP120 phones, and will be adding additional phone types in the future. When the phone type is selected, another configuration option is available to program the button mapping of each telephone model. The IPitomy IP PBX supports a variety of pre-programmed buttons like BLF, park, voicemail, as well as custom configurable speed dial buttons. Each phone can be configured for its own unique set of buttons.

Phone MAC

All of the IP phones have a MAC Address. The MAC ID identifies the piece of equipment for configuration. The auto configuration features of IPitomy rely on the MAC address to load the proper configuration files into the telephone when changes are made in the Web-based interface. The configuration files are stored on the IPitomy IP PBX and used when the phone powers back on after a power down cycle. If the configuration files have been updated when the phone powers back on, a new configuration is loaded into the phone. When the new configuration file is loaded, manual settings on the phone take priority and will be kept intact during the upgrade. Note that at this time only Aastra phones require and utilize the MAC address in the phone settings.

Qualify

This is the interval of time between checking registration for the phone. Default is set to 8000 and should not be changed unless instructed by an IPitomy representative.

2011 Copyright  IPitomy Communication, LLC

61 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide This is where you set what kind of DTMF signaling the extension will use. The dropdown lists options are:

DTMF Mode



rfc2833



auto



info

• inband Typically you would want the DTMF type to be info on both the PBX and in the phone itself. User Type

This is defaulted to Friend and should not be changed unless instructed to do so by an IPitomy representative.

Call Limit

This is the number of concurrent calls allowable at an extension. The Call Limit selected must be between 1 and 99. Default is set to 4. It needs to be above 0 for BLF keys to function. This parameter allows a device to reconnect calls midstream.

Can Reinvite



YES = if the phone type allows the re-invite feature



NO = if the phone type does not allow the re-invite feature



N/A = accepts the system wide default defined in the System Setup section of the Administration System. If the default setting is acceptable and works within your business, we recommend leaving the parameter set to N/A.

This parameter allows you to specify how to handle connections with peers. Explanation of the different options available on the drop-down list are:

Insecure

Music On Hold



PORT = Ignore the port number where authentication came from.



INVITE = Do not require the initial invite to authenticate.



PORT.INVITE = Do not require initial invite to authenticate and ignore the port where the request came from.



YES – To match a peer based by IP Address only and not the port.



VERY – To allow registered hosts to call without re-authenticating. This is the default setting.

This setting allows the user to select a different Music On Hold playlist for their extension then the system default playlist.

Table 19 – Extensions Advanced Networking Settings and Descriptions

Edit Extensions - Network Settings

STEPS: 1

From the Edit Extensions page, locate the extension that you want to update. Click the (edit extensions) icon to the right of the name.

You can also edit multiple extensions by selecting (placing a checkmark) in the boxes to the left of the extensions you want to update. Click the Edit PBX Settings button located at the top right hand corner of the list.

2011 Copyright  IPitomy Communication, LLC

62 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide You will see the extensions that are currently being updated. Make sure that the “Only save the changed fields” box is selected. 2

The Extension Details page appears. Select the Settings page.

link to open the Advanced

3

Make the necessary changes in the Network Settings section of the page.

4

Click button to save the changes. The system returns you to the Edit Extensions page.

5

Click the Apply Changes link located on the right hand corner of the page, to commit the changes to the database.

Extensions - Voicemail Settings Section These settings manage voicemail messaging and routing. Mailboxes created when the extension is built can either be edited on the Advanded section of the extension or on the Voicemail section under Destinations.

Figure 35 – Extensions Voicemail Settings Section

2011 Copyright  IPitomy Communication, LLC

63 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide This table describes the voicemail setting options for each extension. Sections/Fields Mailbox

Description This is the number associated with the extension. Select to enclose the message received in a notification e-mail as an attachment to the email address entered for the extension. An audio file (.Wav) will be the attachment. This requires for Unified Messaging to be configured on the PBX.

Attach to Email

YES = attach message to email. NO =do not attach message to email. N/A = accepts the system wide default defined under PBX SetupVoicemail. If the default setting is acceptable and works within your business, we recommend leaving the parameter set to N/A. Delete the voicemail after it has been emailed to the email address provided for the extension in General Settings. YES = delete message after emailing.

Delete After Emailing

NO = do not delete message after emailing. N/A = accepts the system wide default defined under PBX SetupVoicemail. If the default setting is acceptable and works within your business, we recommend leaving the parameter set to N/A. Note: This option should not be enabled with turn old after emailing. If you enable both, the message will not be emailed but it will be deleted. After emailing, the system moves the voicemail message to the Old folder.

Turn Old After Emailing

YES = will move message to Old messages folder after emailing. NO = messages will not be moved after emailing. Note: This option should not be enabled with delete after emailing. If you enable both, the message will not be emailed but it will be deleted. State Caller ID prior to playback of the message. YES = play caller id prior to message content.

Say Caller ID

NO = do not play caller id prior to message content. N/A = accepts the system wide default defined under PBX SetupVoicemail. If the default setting is acceptable and works within your business, we recommend leaving the parameter set to N/A. Allow callers to review a message after they have recorded it. YES = give callers leaving messages the option to review and rerecord the message they are leaving.

Allow Review

NO = do not give callers the option to rerecord. N/A = accepts the system wide default defined under PBX SetupVoicemail. If the default setting is acceptable and works within your business, we recommend leaving the parameter set to N/A.

2011 Copyright  IPitomy Communication, LLC

64 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide Allow pressing “0” during the voicemail greeting to reach the system-wide operator. YES = allow dialing 0 from mailbox. Allow Operator

NO = disallow dialing 0 from mailbox. N/A = accepts the system wide default defined under PBX SetupVoicemail. If the default setting is acceptable and works within your business, we recommend leaving the parameter set to N/A. Play the time of call prior to the message. YES = enabled.

Play Envelope Message

NO = disabled. N/A = accepts the system wide default defined under PBX SetupVoicemail. If the default setting is acceptable and works within your business, we recommend leaving the parameter set to N/A.

Auto Delete Voicemail In

Define the number of days in which voicemail messages are to be automatically deleted from a mailbox. If this is set to “0” (zero) the voicemail message will never expire.

Allow Dial Out Access

This allows the ‘Dial Out’ feature when a user is listening to their voicemail.

Exclude from Directory

This indicates whether to exclude this extension from the directory.

Mailbox Operator

If a caller presses “0” (zero) while listening to your mailbox greeting, the caller will be routed to this destination. Also, this is where a user will be sent if he dials ”0” from this extension. Set this to None to use the system default which is set under PBX Setup General.

Mailbox Exit Destination

The Mailbox Exit Destination is where the system will route a caller who presses # when they finish leaving a voicemail message. Setting this to None will use the system default, which is set under PBX Setup General. Table 20 – Voice Mail Settings and Descriptions

Edit Voicemail Settings The following outlines the steps to set voicemail parameters.

STEPS: 1

From the Edit Extensions page, locate the extension that you want to update. Click the (edit extensions) icon to the right of the name.

You can also edit multiple extensions by selecting (placing a checkmark) in the boxes to the left of the extensions you want to update. Click the Edit PBX Settings button located at the top right hand corner of the list. You will see the extensions that are currently being updated. Make sure that the “Only save the changed fields” box is selected. 2

The Extension Detail page appears. Select the Settings page.

3

Make the necessary changes in the Voicemail Settings section of the page.

2011 Copyright  IPitomy Communication, LLC

65 www.ipitomy.com

link to open the Advanced

v4.0.1

IPitomy IP PBX Admin Guide 4

Click button to save the changes. The system returns you to the Edit Extensions page.

5

Click the Apply Changes link located on the right hand corner of the page, to commit the changes to the database.

Extensions - Allow CODECs Section These transmission speeds are configured by the service provider and designed to automatically register in the extension through the system.

Figure 36 – Extensions CODECS Settings Page

Sections/Fields

Description

CODEC Permissions (Allow CODECs)

Allows the administrator to define which codec the extension should use, and specify a priority from top down. !

IMPORTANT: Please contact IPitomy’s Technical Support Group for assistance if you feel you need to change these settings.

Table 21 – Extensions CODECS Settings and Recommendations

Edit CODEC Settings The following outlines the steps to set CODECs parameters.

STEPS: 1

From the Edit Extensions page, locate the extension that you want to update. Click the (edit extensions) icon to the right of the name.

You can also edit multiple extensions by selecting (placing a checkmark) in the boxes to the left of the extensions you want to update. Click the Edit PBX Settings button located at the top right hand corner of the list. You will see the extensions that are currently being updated. Make sure that the “Only save the changed fields” box is selected. 2

The Extension Detail page appears. Select the Settings page.

2011 Copyright  IPitomy Communication, LLC

66 www.ipitomy.com

link to open the Advanced

v4.0.1

IPitomy IP PBX Admin Guide 3

Make the necessary changes in the Allow CODECs Settings section of the page. Clicking Up or Down when highlighting a codec will allow you to raise or lower its usage priority.

4

Click Extensions page.

5

Click the Apply Changes link located on the right hand corner of the page, to commit the changes to the database.

button to save the changes. The system returns you to the Edit

Extensions Calling Permissions Section Calling permissions define the types of calls that can be sent and received from an extension and the call actions this extension can take. For example, you may want to limit who has the ability to monitor another extension.

Figure 37 – Extensions Calling Permissions Section The following table describes the settings for an extension’s calling permissions. Sections/Fields

Description

Allow User to Control Forwarding

If Enabled (checked), this allows the user to modify their forwarding and schedule settings when they log into the Smart Personal Console user interface.

Allow User to Control Follow-Me

If Enabled (checked), this allows the user to modify their Follow-Me settings when they log into the Smart Personal Console user interface.

Allow User to Control Phone Key Settings

If Enabled (checked), this allows the user to modify their Phone Key settings when they log into the Smart Personal Console user interface.

Internal Calls

If Enabled (checked), this permits calls made from internal extensions.

2011 Copyright  IPitomy Communication, LLC

67 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide Allow Incoming Intercom Paging

If Enabled (checked), this permits a page to be heard through this extension.

Allow Outgoing Intercom Paging

If Enabled (checked), this permits a page to be made through this extension.

Allow User to Forward Calls

If Enabled (checked), this permits an extension to forward a call or voicemail message to another destination on the system.

Allow User to Record Calls

If Enabled (checked), this permits the extension to record phone conversations.

Allow user to Listen to Others’ Calls

If Enabled (checked), this allows the user to listen to other user’s phone conversations.

Allow User to Whisper

If Enabled (checked), this allows the user to whisper to another user during a phone conversation. Whisper is similar to Listen but you can coach and only the person at the extension can hear.

Allow Others to Whisper

If Enabled (checked), other extensions can Whisper to your extensions calls

Allow Others to Listen

If Enabled (checked), other extensions can Listen to your extensions calls

Allow Others to Record this User’s Calls

If Enabled (checked), other extensions can Record calls at your extension

Allow Call Park

If Enabled (checked), this permits extension to park a call.

Is Operator

If Enabled (checked), the extension is designated as an operator. Being an operator allows the extension to control Day/Night mode overrides. Table 22 – Calling Permission Settings and Descriptions

Add/Edit Calling Permissions The following outlines the steps to set calling permissions for extensions.

STEPS: 1

From the Edit Extensions page, locate the extension that you want to update. Click the (edit extensions) icon to the right of the name.

You can also edit multiple extensions by selecting (placing a checkmark) in the boxes to the left of the extensions you want to update. Click the Edit PBX Settings button located at the top right hand corner of the list. You will see the extensions that are currently being updated. Make sure that the “Only save the changed fields” box is selected. 2

The Extension Detail page appears. Select the Settings page.

3

Make the necessary changes in the Calling Permissions section of the page.

2011 Copyright  IPitomy Communication, LLC

68 www.ipitomy.com

link to open the Advanced

v4.0.1

IPitomy IP PBX Admin Guide 4

Click Extensions page.

button to save the changes. The system returns you to the Edit

5

Click the Apply Changes link located on the right hand corner of the page, to commit the changes to the database.

Extensions - Follow-Me Section The Follow Me feature allows the PBX to try and find a user by calling pre-configured numbers, simultaneously or in sequence of priority. Once answered, the called party is given the option to accept or reject the call. If the call is rejected, or not answered at all, the call will return to the PBX allowing the caller to leave a Voice Mail message.

Figure 38 – Extensions Advanced Settings Follow Me Setup Page

From this window it is easy to configure numbers to be dialed by the system in order to find the user. You can adjust the Name, Number (Number to be dialed), Type of Device that is being called, Rings to wait for an answer, and you can weight the priority from 1-20 (20 being lowest 1 being highest) to define search order. The Use radio box allows you to easily turn on and off numbers to be dialed. Since the SPC can be accessed via remote management, this allows the users to modify and create these lists from remote locations easily. The following table details the parameters and descriptions necessary to configure the Follow-Me feature. The system also allows you to record your own Prompts (recordings) under PBX SetupPrompts, and then use 2011 Copyright  IPitomy Communication, LLC

69 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide those prompts as custom messages for FollowMe feature.

Sections/Fields

Description

Play the Incoming Message to Caller before Starting Search Record the Caller’s Name and Play it to You

When Enabled (checked), the system plays the Status Prompt to the caller. When Enabled (checked), the caller will be asked to record their name, and will announce that recorded name prior to prompting the called party to accept or reject the call.

Play the Unreachable Message if You Could Not Be Found

When Enabled (checked), this will play the Sorry Prompt if the call is not answered, otherwise it goes right to the voicemail greeting.

Number of Seconds to Total Search Time so Caller Has Time to Listen & Record

This allows you to configure how many seconds the system will spend searching for the called party. Default is 12 seconds.

Call From Prompt

This plays when Record the Caller’s Name and Play it to You is enabled (checked). The system default message is “Incoming Call From” followed by the recording the caller made of their name.

No Recording Prompt

This plays when Record the Caller’s Name and Play it to You is disabled (not checked). The system default message of “You have an incoming call” followed by the Options Prompt.

Options Prompt

This plays after you have answered the call and prompts you to press either “1” to accept the call or “2” to reject the call. The system default message can be changed, but the options remain the same.

Please Hold Prompt

This plays to the caller alerting them that the system is going to find the user they are trying to reach. The system default message of “Please hold while I try to locate the person you are calling” will play during the search process.

Status Prompt

This plays the system default message of “The person you are calling is not at their desk, I will try to locate them for you”.

Sorry Prompt

This plays if the person could not be reached or they reject the call. The system default message of “I’m sorry, but I was unable to locate the person you were calling”.

Music On Hold

Numbers

This allows you to specify a particular Music On Hold playlist to play to the caller during the search process. The system default Music on Hold (set at PBX SetupMusic on Hold) will play when this parameter is set to system default. If selected (checked), the Follow Me feature will try to either simultaneously or in sequence of priority to try and locate you by using this call list. Table 23 – Extensions Follow Me Settings and Descriptions

Add/Edit Follow Me Settings The following outlines the steps to set calling permissions for extensions. 2011 Copyright  IPitomy Communication, LLC

70 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide STEPS: 1

From the Edit Extensions page, locate the extension that you want to update. Click the (edit extensions) icon to the right of the name.

2

The Extension Detail page appears. Select the Settings page.

link to open the Advanced

3

Click on the Numbers and Settings button under the Follow-Me section of the Advanced page.

4

The Administrator View – Follow-Me Settings/Extensions window appears.

5

Make the necessary changes in the Follow-Me parameters. Click on the SAVE button to save the changes to the Follow-Me settings. A message confirming the changes will appear.

6

Click the EXIT button to close the window.

7

Click Extensions page.

8

Click the Apply Changes link located at the right hand corner of the top of the page, to commit the changes to the database.

button to save the changes. The system returns you to the Edit

Provisioning - Auto-Discovery Tab This network discovery tool will automatically detect new devices that have been added to the network. This feature helps identify phones and other devices connected to the network and allow you to configure networked phones. The IP PBX system provides you with the option to either scan the network, or if a scan has been done recently, you could select No Scan to save time.

Figure 39 – Extensions Auto-Discovery Tab

Start Auto-Discovery Scan This section describes how to start the Auto-Discovery scan for active devices on the network.

STEPS: 1

From the DestinationExtensions page, click the Auto-Discovery Tab.

2

Select to either Scan or Not Scan the network and an Alert message indicating that the system is scanning the network for active devices appears.

3

Once the scanning process is complete, the system will display a list of active devices and assigned values such as IP Address, Device Type, Status, etc. Devices that appear

2011 Copyright  IPitomy Communication, LLC

71 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide on this list may be selected for editing. By default, the PBX will only display IPitomy and Aastra devices. Filter options can be modified to change display other devices.

If you click the refresh-view more than once within a short time period, the network is not rescanning. The minimum time period allowed between scans is indicated under the Advanced Settings (Min Refresh Interval). The network is only scanned for new information when you click REFRESH. Both REFRESH and FILTER ONLY apply whatever filters you have chosen to the displayed list. List of Devices & Extensions The list of discovered network devices comes from two sources: •

Network



PBX Database

Figure 40 – Auto-Discovery Device Color Legend

2011 Copyright  IPitomy Communication, LLC

72 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide The following table describes the status of devices that will appear once an Auto-Discovery scan is completed. Sections/ Fields

Description

Assigned

This field indicates that extension that is assigned to the device (phones). Clicking on the box to the left of this field allows you to select it for editing.

Device

The Device column lists info about the device. Database info is preferred, so if a device is set to a certain phone type in the database, this is listed instead of the actual device type. This is the status of the device. If the status field is blank, this indicates that the device was not found on the network.

Status

NOTE: Phones that are in the process of restarting, turned-off, or operating on a different network during a network scan will not be in an “Online” status.

Hovering the mouse over this icon will provide device information. See Figure 43 for an example of the data that can be viewed. MAC Address IP Address

This is the MAC Address assigned to the device. This is the IP Address assigned to the device. Table 24 – Auto-Discovery Scan Details

Device Information To view detail information for a specific device, hover your cursor over the information icon to obtain details about the network device or phone. This can be an important source of information about which phones are available for live configuration.

Figure 41 – Auto- Discovery Device Values

2011 Copyright  IPitomy Communication, LLC

73 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Edit Selected Tab The IP PBX system offers many ways to configure devices. This section describes an optional method using the Auto-Discovery feature.

Figure 42 – Auto-Discovery Edit Selected Functions

The following table describes the fields and functions available on the Edit Selected Tab of the Auto-Discovery page:

Fields

Description

Create Assign Unassign Unassign & Default

Commands Phone?

Create new extensions for selected phones. You can upload extension details in a file or manually enter information.

NO

Assign existing extensions to selected phones.

NO

Removes the configuration file for the phone and all association between the extension and the phone.

NO

Same as Unassign but also sends a Factory Default instruction to the phone.

YES

Table 25 – Auto-Discovery Edit Selected Tab Functions and Descriptions

Create, Assign and Configure Phone The following outlines steps to create, assign and configure a device. !

IMPORTANT: This assumes that the phones are in a FACTORY DEFAULTED state. IPitomy recommends using the CSV upload file and the IP550 phone type which will help to simplify the setup and auto configuration process.

2011 Copyright  IPitomy Communication, LLC

74 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

STEPS: 1

From the ExtensionsDestinationsAuto-Discovery page, click the Edit Selected tab.

2

Place a check mark next to the phones you wish to use when creating the extensions

3

Click the Create button.

4

Enter the new extension information. The MAC addresses of the selected phones will be populated so you have a reference as to what phones you are creating the extensions for.

5

Click the “Create” button. If successful, Click “Return to Extensions”

6

Click the Apply Changes link located at the right hand corner of the top of the page, to commit the changes to the database.

7

Click the “Auto-Discovery” button and you will note the newly created extensions are now assigned to the phones that were checked.

8

Check the boxes next to the phones that you just created extensions for.

9

Click the Commands Tab.

10 Click on the Configure & Restart button to provision the phones.

View Settings Tab Filtering does not change how the network scanning is performed. It only limits the list of items displayed. This means that if you only want to change filters it is not necessary to re-scan the network. All of the network information from the last network scan is retained and used by filters.

Figure 43 – Auto-Discovery View Settings Page

2011 Copyright  IPitomy Communication, LLC

75 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Sections/Fields

Select All, None, Invert

Refresh

Filter Only

Description

Commands Phone

Check or uncheck multiple checkboxes with the click of a button.

NO

Scan the network for devices. Scanning is done using the settings in Advanced Scan Settings. The scan results displayed depend on the active filters,controlled via Advanced Filter Settings.

NO

Displays results of the last network scan after applying the filters set in Advanced Filter Settings.

NO

Table 26 – Auto-Discovery Functions and Descriptions Advanced Filter Settings

Figure 44 – Auto-Discovery Advanced Filter Settings Sections/Fields Sort Order Hide

Description This allows you to set what order items are listed. Hover your cursor over the help icon next to the Sort Order fields for options. Allows you to hide different status types from view. Allows you to either enter a partial MAC or IP here. The only system criterion is that the pattern must match from the first character onward. i.e. “000D” would match “000DE” but not “A000DE”.

Filter Patterns

Full Regular Expression Matching is supported when you enclose your search pattern in double quotes. Some Examples are: • Pattern 1.2.3 = ^1\.2\.3 • Pattern “1\.2\.3.*” = 1\.2\.3.* You can select multiple device types to filter by. Auto-Discovery is aware of MAC address ranges used by many popular networked devices. Although this is not the only way Auto-Discovery identifies devices, this allows the tool to identify and filter devices by type.

Filter by Type

Only IPitomy devices and Aastra phones are shown by default because they are set in the Filter by Type.

2011 Copyright  IPitomy Communication, LLC

76 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide Table 27 – Advanced Filter Settings and Descriptions Advanced Scan Settings Changes to Scan Settings are kept when you click the GUI ‘Refresh’ button. Clicking on your browser’s refresh button will discard changes. For the most part these settings can remain unchanged and all will function as needed.

Figure 45 – Auto-Discovery Advanced Scan Settings Page

Sections/Fields

Min Refresh Interval Maximum wait Packet Count

Description Minimum number of seconds required between fresh network scans. If you attempt to scan the network more often than this you only get results stored from a previous scan. Maximum number of seconds to wait for all packets to return. Number of packets to send

TX Interval

Transmission interval between packets. Only meaningful when Packet Count is greater than 1. Minimum allowed value is 0.2

Batch Size

Divide scanning range into batch jobs. Jobs are run sequentially. Each job will have at most pings running in parallel at a time. The special value 255 means run all pings as one big job.

Network

Network address with last octet reserved for From and To range. Example: 192.168.1.x

From To

Start number for last octet of network address. End number for last octet of network address.

2011 Copyright  IPitomy Communication, LLC

77 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide Send Wakeup ping before Survey Ping if…

Some devices are slow to respond to the first ping they receive but have faster response times afterwards. Maximum seconds to wait for basic phone web interface to signal that it is alive. Rarely used.

Port 80 Ping Wait

Maximum seconds to wait for most commands.

Command Wait User and Password

Phone’s Web User Name & Password may have to be specified if the phone is not using factory default settings for these items. When these fields are blank Auto-Discovery uses default settings.

Factory Default Wait

Maximum seconds to wait for the phone to signal completion of a Factory Default.

Reset

The ‘Reset’ button will return all Scan Settings to original default values. Table 28 – Auto-Discovery Advanced Scan Settings and Descriptions

Commands Tab The IP PBX system offers many ways to configure devices. This section describes an optional method using the use Auto-Discovery feature.

Figure 46 – Auto-Discovery Command Functions Page

Sections/ Fields

Factory Default Restart Configure & Restart

Description

Commands Phone?

Sends a Factory Default and restarts the phone.

YES

Sends a Restart instruction to the phone.

YES

Instructs phone to set TFTP server to the Server IP specified under Advanced Settings. Then the phone is commanded to restart, which will result in pulling down configuration files and firmware files if there are updated ones present.

YES

Combines the functions of the Assign button with the Configure & Assign, Configure & Restart button. Restart Table 29 – Auto-Discovery Command Settings and Descriptions

2011 Copyright  IPitomy Communication, LLC

78 www.ipitomy.com

YES

v4.0.1

IPitomy IP PBX Admin Guide Factory Default Phone

STEPS: 1

From the ExtensionsDestinations page, click the Auto-Discovery Tab.

2

Click the “Auto-Discovery” button, choosing to scan or not scan the network as needed.

3

Click (placing a checkmark) on the boxes next to phones you wish to default.

4

From the Auto-Discovery page, click on the Command tab. Click the “Factory Default” button. Wait long enough for the phones to default and restart. This could be anywhere from 30 seconds to 2 minutes for each phone, depending on the model. The phones will set themselves back to factory default and reboot during this period.

Troubleshooting Network Scanning Problems Scan settings have been configured to work in a standard one subnet network environment. More complicated environments may require further tuning. The most useful setting is ‘Maximum wait’. However noisy environments will require increasing the packet Count and TX interval.

STEPS: To tune scanning for your network: 1

From the ExtensionsDestinationAuto-Discovery page, click on Advanced Scan Settings link.

2

Increase the ‘Maximum Wait’ setting by a few seconds.

3

Click the GUI ‘Refresh’ button.

More specific tuning will require knowledge of your network and diagnostic tools like Ping. Phones that are in the process of restarting, turned-off, or operating on a different network during a network scan will not be in an “Online” status.

2011 Copyright  IPitomy Communication, LLC

79 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Auto Provisioning Phone Settings from Actual Device The remainder of the configuration is done via the Phone interface, and will only work with IPitomy phones.

STEPS: 1

Create an extension, setting the Device to either IP550 or IP120, depending on what IPitomy phone you intend to register to the extension. IMPORTANT: To configure the phone using the auto provisioning, !

make sure that the “Auto-Provisioning” parameter is RUNNING. This can be done in PBX Setup General option of the system.

2

From your phone, select the Menu button to start Auto-Provisioning then select Option 7: SIP Settings (you can do this without using the scroll keys by just pressing Menu then 7).

3

It will prompt you for the Admin password. Enter the default password “1234” then press the Enter softkey (IP550) or the OK button (IP120)

4

Select Option 8: Auto Prov.

5

Select “YES” when the Autosearch PBX prompt appears.

6

Enter either the extension number of the extension that has been created.

7

Press the Done softkey (IP550) or the OK button (IP120) and the phone will run through the process of downloading its configuration file, updated firmware file, etc.

Edit Phone Settings The settings for each individual device (phone) can be configured in the IP PBX system. The following outlines the steps to modify the phone settings from the IP PBX system.

View Phone Settings

Figure 47 – Extension Listing

2011 Copyright  IPitomy Communication, LLC

80 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Edit Phone Settings

Figure 48 – Edit Phone Settings Page Sections/ Fields Settings for Top Section of the Phone Setting Settings for Bottom Section of the Phone Setting

Description Many phone models have multiple areas where you can set keys. The TOP section typically refers to the keys around the LCD screen, or Soft keys. Many phone models have multiple areas where you can set keys. The BOTTOM section typically refers to the Programmable keys. See Appendix 1 for details on key types.

Type

Key type determines what function a key performs. A dropdown list shows which key types are available to the phone model you are working with.

Label

This is the label associated with this key. If configured for a key around the LCD screen, this is what will display.

Value

The value completes a key’s function. It may contain a number to dial special codes or allow you to select an extension from a dropdown list. Most key types do not require you to enter a value. For example, the Voicemail key does not require a value because the System Administrator determines it for the end user.

2011 Copyright  IPitomy Communication, LLC

81 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide Only necessary when configuring Soft Keys around the LCD screen. When checked, the key in question will display when the phone is in the states defined: Key State

Idle – No current call activity Connected – A call is connected Outgoing – A call is being placed from the extension Incoming – A call is ringing the extension Table 30 – Edit Phone Settings and Descriptions

STEPS: 1

From the ExtensionsDestination page, find the extension you want to edit.

2

Click on the page appears.

3

Make the necessary changes to the settings for the phone the click the Save & Restart Phone button.

4

The PBX will update the configuration file and reboot the phone so that it can download the updated information for the keys.

icon to the right of the extensions name. The Edit Phone Settings

2011 Copyright  IPitomy Communication, LLC

82 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Edit Advance Phone Settings The advanced settings page varies by the type of phone you are configuring. The following outlines the advance parameters for IPitomy phones, as well as Aastra phones.

Edit Advance Phone Settings – IPitomy Phones

Table 31 – Edit Advanced Phone Settings – IPitomy Phones

2011 Copyright  IPitomy Communication, LLC

83 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Sections/ Fields

Description Custom SIP Settings This defines whether the phone is communicating to the PBX over the LAN, WAN, or a Custom server address. LAN – Tells the phone to communicate to the local IP of the PBX

Network

WAN – Tell the phone to communicate to the public IP of the PBX, as entered under PBX SetupSIP Custom – Tells the phone to communicate to the PBX via an IP you enter manually

Server

Displays the IP of the PBX as configured from the previous setting. If Network is set to Custom, this is where you would manually set the IP. Time Settings Defines where the phone will get its time settings from.

Network

PBX – Sets the PBX local IP as the time server for the phone Custom – Allows you to manually enter a time server for the phone.

Time Server

Displays the address the phone is using for its time server. When set to Custom this field allows you to manually enter the time server address. Allows you to set the time zone the phone will use. System – the phone follows the PBX time zone settings

Time Zone

Custom – Select from the dropdown of a number of time zone settings, allowing the phone to display a different time then the PBX would Volume Controls

Microphone Mute

Default N; The IP550 phone will answer a page call and automatically engage Mute when this option is selected.

Auto-Answer Incoming Intercom

Default Y; If enabled, this will automatically answer incoming pages via speakerphone. If the user is on a call, the page will ring the extension instead.

Warn on Incoming Intercom

Default Y; If enabled the phone will play a tone alerting the user that their phone has answered a page with the speakerphone.

Call Waiting Tone

Default Y; If enabled the phone will play a tone while the extension is busy on a call alerting the user that another call is waiting.

Stutter Tone

Default N; Stutter Dial Tone is provided to alert a user that messages are waiting. It is presented to the user at the time the handset is taken off-hook or speakerphone button pressed from an idle state.

Handset Gain Level

Default 10; Gain can be loosely defined as volume. This setting allows the programmer to adjust the gain to the user’s handset. DREW what is the range?

Headset Gain Level

Default 10; Gain can be loosely defined as volume. This setting allows the programmer to adjust the gain to the user’s headset. DREW what is the range?

2011 Copyright  IPitomy Communication, LLC

84 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Other Options Default 4; This is a counter that determines how long the telephone will wait between digits dialed before sending digits dialed by the user to the PBX. The shorter the time the faster the call will be placed, BUT short times mean that a user has to enter all digits without delaying more than this time period or the call will be routed with fewer than required digits and may not route properly.

Digit Timeout

Backlight

Default N; This is the backlight of the LCD display. Setting this option to yes will force the LCD backlight to remain ON at all times.

Backlight Time

Default 10; When the Backlight option above is set to “N” (default) this timer determines how long the backlight will remain ON following the last activity.

Display Call Waiting

Default Y; The IP550 has the ability to display cal waiting information on the display of a busy extension. If this is desired set this to Yes.

Display Missed Calls

Default Y; The IP550 telephone has the ability to display the number of calls that rang but were not answered. If desired, select Yes. Default N; This option is provided to disable telephone (phone-based) Call Forward. This is often desired since the user may invoke a mode of Call Forwarding not desired and conflicting with call forward conditions implemented in PBX programming.

Disable Phone Forwarding

This is also beneficial in hospitality applications when a telephone is installed in a location where the user should not be given the ability to use cal forward.

Display Softkey Dots

Default N; The IP550 has been enhanced to provide an alignment “Dot” at the edge of the display for each of the Softkey function prompts. For users that find it difficult to associate Softkey prompts to Softkeys, enable this option.

Table 32 – Edit Advanced Phone Settings for IPitomy Phones

STEPS: 1

From the ExtensionsDestination page, find the extension you want to edit.

2

Click on the page appears.

3

Click the Advanced Settings link at the bottom of the page.

4

Make the necessary changes to the settings for the phone the click the Save & Restart Phone button. This will update the configuration file and when the phone reboots, it will download the new information.

icon to the right of the extensions name. The Edit Phone Settings

2011 Copyright  IPitomy Communication, LLC

85 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Edit Advance Phone Settings – Aastra Phones

Figure 49 – Aastra Advanced Phone Settings Page

Sections/ Fields

Description Display Section

Caller's List

If Enabled, the Missed/Dialed/Answered calls on Aastra phones will display. Custom Sip Settings This defines whether the phone is communicating to the PBX over the LAN, WAN, or a Custom server address. LAN – Tells the phone to communicate to the local IP of the PBX

Network

WAN – Tell the phone to communicate to the public IP of the PBX, as entered under PBX SetupSIP Custom – Tells the phone to communicate to the PBX via an IP you enter manually

Server

Displays the IP of the PBX as configured from the previous setting. If Network is set to Custom, this is where you would manually set the IP. Time Settings Defines where the phone will get its time settings from.

Network

PBX – Sets the PBX local IP as the time server for the phone Custom – Allows you to manually enter a time server for the phone.

Time Server

Displays the address the phone is using for its time server. When set to Custom this field allows you to manually enter the time server address.

2011 Copyright  IPitomy Communication, LLC

86 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide Allows you to set the time zone the phone will use. System – the phone follows the PBX time zone settings Time Zone

Custom – Select from the dropdown of a number of time zone settings, allowing the phone to display a different time then the PBX would Volume Controls

Headset Transmit Gain Headset Side Tone Gain Handset Transmit Gain Handset Side Tone Gain Microphone Mute

Applies to Aastra Only - This allows you to set the gain on the transmission of calls made using a headset. Applies to Aastra Only - This allows you to set the gain on for the headset side tone. Applies to Aastra Only - This allows you to set the gain on the transmission of calls made using the handset. Applies to Aastra Only - This allows you to set the gain on the handset side tone. This defines if the phone will answer a page in a muted state. Applies to Aastra Only - If enabled, this allows a page to place your current active call on hold, and answers the page with the speaker phone.

Allow Intercom Barge In Switch UI Focus to Ringing Line

Applies to Aastra Only - Aastra phones switch the UI Focus to the line ringing in. Aastra Expansion Modules This allows you to change the type of module for the phone.

Module Type

!

IMPORTANT: Changing this parameter will delete the existing module key settings.

Table 33 – Aastra Advanced Phone Settings and Descriptions

STEPS: 1

From the ExtensionsDestination page, find the extension you want to edit.

2

Click on the page appears.

3

Click on the Advanced Settings link. The Advanced Settings page for the phone appears.

4

Make the necessary changes to the settings for the phone the click the Save & Restart Phone button. This will update the configuration file and when the phone reboots, it will download the new information.

icon to the right of the extensions name. The Edit Phone Settings

2011 Copyright  IPitomy Communication, LLC

87 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Groups A Group is a logical grouping of extensions and their privileges. Each Group is associated with a set of PBX features and call routing strategies. It is advised to build the extensions in the PBX first, allowing the groups to be populated at the time of creation. These Groups allow incoming calls to be distributed to a group of extensions rather than just one extension. Within the Groups, different distribution strategies may be selected based on the call coverage required by the application. Groups also provide off-hook paging functionality. By dialing the intercom button or code followed by the group number, extensions in the group will receive the page over the intercom. Groups are a set of extensions that are related either because they: • • •

Serve a similar business function. Work within the same department. Are located in proximity to each other.

For example, a business might create a few user Groups in an IP telephony network, e.g. Sales, Marketing, Administration, Accounting, Engineering, etc. Groups may also be created for people in similar locations like a plant floor, the north section of a building or the front office. The goal of a group is to ring telephones based on the incoming routing logic (e.g. DIDs, Auto Attendant selected by the incoming caller, or time of day). Note that calls routing to an extension from a ring group will ignore that phones PBX forwarding settings. Some phones have forwarding settings which are independent of the PBX (not set through the PBX Web GUI). These settings will still be applied.

Figure 50 – Ring Groups Page

2011 Copyright  IPitomy Communication, LLC

88 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide Ring Group Examples Ring groups define a set of extensions (people) that answer calls. Ring groups can be created for departments (e.g. Sales, Engineering) or buisiness regions (e.g. north, south, etc), or areas of a business (e.g. a warehouse or plant floor). These ring groups can appear on an Automated Attendant (menu). When the group is selected from a Menu, the call is routed to the group. These calls will be distributed to the member extensions based upon the ring strategy for the group. The ring strategy for the group can be set from the drop-down list. Available call distribution options are: • • • • • •

Ring All – Ring all extensions in the group simultaneously Round Robin – Take turns ringing each extension, starts at the first extension for each new call Round Robin (with memory) – Take turns ringing each extension, starts where the last call left off Least Recent – Ring extensions in order of which was least recently called by the queue Fewest Calls – Ring extension in order of which has the fewest completed calls from the queue Random – Randomly ring one extension at a time

Example Ring Group 1 – Departmental Grouping Ring group definitions can be found in the Add a New Ring Group section of this guide. If a business has the following departments and people: This business can setup the following ring groups supporting business operations.

GROUP 1 - Sales

Ext.

GROUP 2 – Customer Services

Ext.

Cathy Caldwell

123

Gretchen Goodall

134

David Dawson

124

Peter Polk

135

Susan Smith

125

Robert Reed

126

Using this ring group scenario the Menu would look like: • • •

Sales (Destination - Group 1). Customer Service (Destination - Group 2). Office Manager (Destination - Ext. 113).

The menu prompt (message) for this menu and group arrangement would read as follows: “Thank you for calling CompanyA, a leading manufacturer of cable assemblies and wiring harnesses. If you know the extension of the party you would like to reach you may dial it at any time.” • • •

For Sales, press 1. For Customer Service, press 2. For Accounting, press 3.

Once a call is sent to Sales, member extension will be rang according to the ring group strategy.

Example Ring Group 2 – Regional Sales Grouping GROUP 1 East Coast Sales

Ext.

2011 Copyright  IPitomy Communication, LLC

GROUP 2 -West Coast Sales

89 www.ipitomy.com

Ext.

GROUP 3 Customer Service

Ext.

v4.0.1

IPitomy IP PBX Admin Guide Cathy Caldwell

123

Susan Smith

125

Gretchen Goodall

134

David Dawson

124

Robert Reed

126

Peter Polk

135

Using this ring group scenario the Menu would look like: • • • •

East Coast Sales (Destination - Group 1). West Coast Sales (Destination - Group 2). Customer Service (Destination - Group 3). Office Manager (Destination - Ext. 113).

The menu prompt for this menu and group arrangement would read as follows: “Thank you for calling CompanyA, a leading manufacturer of cable assemblies and wiring harnesses. If you know the extension of the party you would like to reach you may dial it at any time. For” • • • •

East Coast Sales, press 1. West Coast Sales, press 2. Customer Service, press 3. Accounting, press 4.

Calls sent to these groups might use different ring strategies. The East Coast Sales group might answer calls Round Robin, distributing the calls to each Sale Representative consecutively. If a sales person is missing from the West Coast team this group might set phones to Ring All in the group so that calls don’t get missed. The Customer Service team may get high volumes of calls during a specified period of time, so this group may be set to ring Least Recent.

Add/Edit New Ring Group

2011 Copyright  IPitomy Communication, LLC

90 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Figure 51 – Edit Ring Group Page

The following table describes the parameters (fields) on the Edit Ring Group page and their descriptions and recommended settings. Sections/Fields Name

Description The name associated with this ring group.

Group Number (to dial group)

The number dialed to access this ring group. Must be 3 or 4 digits.

Allow Paging with **+Group Number

If enabled (checked), this will allow **+ group number to page this ring group

2011 Copyright  IPitomy Communication, LLC

91 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide This defines how calls are distributed to member extensions. Options are: Ring All – Ring all extensions in the group simultaneously Round Robin – Ring extensions consecutively. Delivers a new call to the first person in the group only after the last person in the group has taken a call. If an extension is busy the call will automatically be routed to the next extension in the group. Round Robin (with memory) – Ring extensions consecutively. Delivers a new call to the first person in the group only after the last person in the group has taken a call. Remembers where the last call was taken and distributes new calls to the next extension in the rotation.

Ring Strategy

Least Recent – Ring extensions in order of which was least recently called by the queue. Fewest Calls – Ring extension in order of which has the fewest completed calls from the queue Random – Distributes calls randomly to the group. Failover Destination

This defines where a call will be sent when it goes unanswered for a duration that matches the Timeout for the group.

Timeout

Defines, in seconds, the total time a call will spend in the ring group before being sent to the Failover Destination Determines if feature code recording is allowed for calls in this queue.

Allow Recording

If YES = enables the recording feature. If NO = disables the recording feature.

Agent Ring Time

Defines, in seconds, how long the queue will ring a particular agent. If using the Ring All strategy, this value should match the Timeout. For other strategies, this should be set to how long an extension should ring before moving on to the next. This deals with how the queue handles multiple concurrent calls. If set to NO the queue will wait until the first call is answered before ringing phones with the second call. If set to YES the queue will ring phones for all calls as they come in.

Autofill

If YES = Distribute calls to group members if they are already on a call If NO = Do NOT distribute calls to group members if they are already on a call

Ring In use

Table 34 – Edit Ring Group Settings and Descriptions The following outlines the steps to add/edit ring group settings.

STEPS: 1

From the DestinationsGroup page, click the ADD Group button. The Edit Ring Group page appears.

2

In the Name field, enter a name for the group.

3

In the Group Number field, enter a number for the group. This number must be three or four digits in length.

4

Check the Allow Paging with **+ the Group Number to enable the setting.

2011 Copyright  IPitomy Communication, LLC

92 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide 5

Select the desired Ring Strategy from the drop-down list.

6

Select the desired Failover Destination from the list of available options.

7

Enter the time for the Timeout parameter.

8

Select “Yes” if you want to enable the Allow Recording setting. Otherwise, set it to “No”.

9

Enter the time for the Agent Ring Time parameter.

10 Select “Yes” if you want to enable the Autofill setting. Otherwise, set it to “No” 11 Select “Yes” if you want to enable the Ring in use setting. Otherwise, set it to “No”

12 Click the

button.

13 From the Members section of the Edit Ring Group page, select the extension number from the list of extensions that you want to add to the ring group. Click the ADD button. 14 A second list appears next to the Members list displaying the selected extension. Repeat step 13 until all extensions that you want to add are on the list. Additionally, Shift or Control click functionality works for adding multiple extensions at once. 15 To remove an item from the list of additions, select the extension number then click the REMOVE button. 16 Define Priorities for the extensions, if needed. The scale ranges 0 thru 9 (0 is the highest priority).

17 Click

button to save the changes.

18 Click the Apply Changes link located at the top right hand corner of the page, to commit the changes to the database.

2011 Copyright  IPitomy Communication, LLC

93 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Ring Group Advanced Settings

Figure 52 – Advanced Ring Group and Custom Caller ID Settings Section

The following table describes the parameters (fields) on the Advanced Settings for Ring Groups page and their descriptions and recommended settings. Sections/Fields

Description Advanced Ring Group Settings Defines what a caller will hear while they are waiting for someone to pick up a call from the call group. Callers can either hear:

Caller Ring Settings

Queue Dial String Ring Tone

Ringing – The phone continues to ring while the caller is waiting. Music on Hold – The caller hears music while waiting for a group member to pick up the call. The dropdown list displays the MOH playlists that are on the PBX. Select a playlist and it will play the sound files found in the playlist. OBSOLETE – and will be removed in a future release. When Caller Ring Settings are set to Ringing, use this to define the ring cadence. Custom Caller ID Settings Defines what method, if any, you wish to use to override Inbound CID. The options are:

Use Name Number Prepend

System Default, Name, Number, Name and Number This is the name of the caller that will be displayed when a call is received. This is the number of the caller that will be displayed when a call is received. Selecting Prepend will enter the text you put in the field, followed by the original CID. If not prepending, the override eliminates the original information. Table 35 – Advanced Ring Group and Custom Caller ID Settings and Descriptions

2011 Copyright  IPitomy Communication, LLC

94 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide Edit Advanced Ring Group Settings

STEPS: 1

Select Destinations Groups. The Ring Groups page appears.

2

Select the Ring Group you want to edit by either select the group name or click on the blue Group Name link.

3

The Edit Ring Group page appears. Scroll down the page and click on the Advanced link. The Advanced Ring Group Settings section is displayed.

4

Make the necessary changes to the settings then click the changes.

5

Click the Apply Changes link located at the top right hand corner of the page, to commit the changes to the database.

icon to the right of the

button to save

Edit Custom Caller ID Settings

STEPS: 1

Select Destinations Groups. The Ring Groups page appears.

2

Select the Ring Group you want to edit by either select the group name or click on the blue Group Name link.

3

The Edit Ring Group page appears. Scroll down the page and click on the Advanced link. The Custom Caller ID section is displayed.

4

Make the necessary changes to the settings then click the changes.

5

Click the Apply Changes link located at the top right hand corner of the page, to commit the changes to the database.

2011 Copyright  IPitomy Communication, LLC

95 www.ipitomy.com

icon to the right of the

button to save

v4.0.1

IPitomy IP PBX Admin Guide

Edit Members/Agents

Figure 53 – Edit Members/Agents Section

Sections/Fields Members Agents

Description This is the list of available extensions that are in the database. This is the list of available agents that are in the database.

Priority

This field allows you to set the priority level for the members or agents. The lower the number, the higher the priority.

ADD

This button will add the select item on the list to the right of the available members or agents. Shift and Control click functionality works for adding more than one at a time.

REMOVE

This button will remove the item(s) that have been selected from the list of available members or agents. Shift and Control click functionality works for adding more than one at a time. Table 36 – Edit Members/Agents Settings and Descriptions

2011 Copyright  IPitomy Communication, LLC

96 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Add Agents/Members to the Group

STEPS: 1

Navigate to the Destinations Groups Edit Group page.

2

Select from the left hand column which agents/members to add to the group.

3

Click the Add button.

4

Click

5

Click the Apply Changes link located at the top right hand corner of the page, to commit the changes to the database

button to save the changes.

Delete Agents/Members from the Group

STEPS: 1

Navigate to the DestinationsGroupsEdit Group page.

2

Select from the right hand column which agents/members to remove from the group.

3

Click the Add button.

4

Click

5

Click the Apply Changes link located at the top right hand corner of the page, to commit the changes to the database

2011 Copyright  IPitomy Communication, LLC

button to save the changes.

97 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Automatic Call Distribution (ACD) Systems licensed to use ACD will have access to additional functionality pertaining to Ring Groups. ACD allows for more flexibility and control over the queuing in a Ring Group, as well as allowing the creation of Agents who can be added to the Ring Group.

Table 37 – Automatic Call Distribution (Agents) Page

2011 Copyright  IPitomy Communication, LLC

98 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Sections/Fields Agent Retry Timer Weight Wrap-up Time

Autopause

Maximum # of people in queue Announce Frequency Periodic Announce Frequency

Announce Holdtime

Description This defines, in seconds, how long the queue will wait before attempting to ring an agent again. The priority of the queue in relation to other queues in the system. This defines, in seconds, how long the queue will wait after an agent has ended a call before flagging then as an active agent ready to accept more calls. This will place an agent in a pause state in relation to this queue when they ignore or answer a call. To become an active member of the queue again unpause using the 1* feature code a phone or 1*+agent# for an agent. Defines how many callers can join the queue before it is considered full. Must be set for Announce Holdtime to function. This pertains to how often the caller will hear the hold time announcement, in seconds This defines how much time passes between playing the recording that was set for this queue under Periodic Announcement. If set to YES this will announce a caller’s status in the queue with regards to their expected hold time, pending the hold time is estimated to be over 1 minute. If the hold time is less than one minute, this will announce the caller’s position in the queue. A period of time is needed for the algorithm to ‘learn’ and estimate hold times accurately. This message will not play for the first caller in the queue. Caller Ring Settings must be set to a MOH file in order for this message to play. Controls if a caller can join a queue. YES = Callers can join the queue with no members or whose members are busy.

Join Empty Queue

NO = Ignores agent and member status, they can be logged out as long as they exist in the configuration callers can join a queue. STRICT = Callers cannot join the queue if there are no members or if the members are all busy, paused, or logged off. Controls if a caller will leave an empty queue. YES = Callers will leave the queue if there are no active members, or all members are busy. If all agents are logged out, the caller will not leave the queue.

Leave Empty Queue

NO = Callers will not leave the queue even if there are no active members, or all members are busy. STRICT = Callers will leave the queue if there are no active members, but will remain in the queue if all members are busy. If agents are pause or logged off, the caller will leave the queue.

Report Hold Time

Set to YES if you want the person answering the queue call to hear a message indicating how long the call they just answered was in the queue

2011 Copyright  IPitomy Communication, LLC

99 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide Member Delay before connect

Timeout Restart

Delay, in seconds, before a member is connected to the queue. If set to YES the ring group timeout will reset after attempting to ring an agent/member. When set to NO, time taken to ring an agent/member will be subtracted from the ring group time, and when the timer ends the group will send the caller to the Failover Destination Set this to the time, in seconds, that defines the acceptable level of service for the queue. The Live Queue Data page will track the percentage of calls answered within the allotted time.

Service Level Exit Status: FULL Exit Status: JOINEMPTY Exit Status: LEAVEEMPTY

These are the destinations where calls will go based on the exit strategy defined. If no one in the group accepts the call this is the destination to which the call will be sent. Destinations can be extensions, other ring groups, a menu or a voicemail box.

Exit Status: JOINUNAVAIL Exit Status: LEAVEUNAVAIL Intro Announcement

Agent Announcement

Define what prompt to play to the caller just before they enter the queue. (Previously “Announce Filename”) Defines what prompt to play to the agent/member who answers the queue call. This setting is set per Queue and therefore can be used to identify what Queue is being answered (for agents handling calls from multiple Queues.

Periodic Announcement

Defines what prompt to play to the caller at the Periodic Announce frequency interval. This will not play for the caller in the first position of the queue. Caller Ring Settings must be set to a MOH file in order for this message to play.

Exit Menu

Set this to a menu. Key presses while in this group will send people the corresponding destination from that menu. Table 38 – Edit Ring Group ACD Agents Settings and Descriptions

Edit Automatic Call Distribution (ACD) Settings

STEPS: 1

From the DestinationsGroups Edit Group page, scroll to the ACD Settings section.

2

Make the necessary updates to the ACD settings.

3

Click

2011 Copyright  IPitomy Communication, LLC

button to save the changes.

100 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide 4

Click the Apply Changes link located at the top right hand corner of the page, to commit the changes to the database.

Add Automatic Call Distribution (ACD) Agents

Figure 54 – ACD Edit Agents Page

Sections/Fields

Description Enter a name that will identify this agent.

Name ID

Enter a unique 3-4 digit number to identify this agent. This number is used to log in/out.

PIN

Enter a minimum of 4 digits for the PIN. This is the password used to log in/out with the agent. Table 39 – Add/Edit Agent Features and Descriptions

STEPS: 1

From the DestinationsGroupsEdit Group page, scroll to the ACD Settings section.

2

Click on the blue Agents link to the right of the words ACD Settings. The Agents page appears.

3

Click on the ADD button to add a new agent. A box with the name, ID and PIN field appears. Enter the information for the new agent.

4

Click

2011 Copyright  IPitomy Communication, LLC

button to save the changes.

101 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide 5

Click the Apply Changes link located at the top right hand corner of the page, to commit the changes to the database.

Edit Automatic Call Distribution (ACD) Agent

STEPS: 1

From the DestinationsGroupsEdit Group page, scroll to the ACD Settings section.

2

Click on the blue Agents link to the right of the words ACD Settings. The Agents page appears.

3

Update the necessary information for agent(s) then click the SAVE CHANGES button. The changes that you made will appear in the updated list.

4

Click the Apply Changes link located at the top right hand corner of the page, to commit the changes to the database

Delete Automatic Call Distribution (ACD) Agent

STEPS: 1

From the DestinationsGroupsEdit Group page, scroll to the ACD Settings section.

2

Click on the blue Agents link to the right of the words ACD Settings. The Agents page appears.

3

From the list of existing agents, click on the box (placing a checkmark) to the left of the Agent(s) that you want to delete. Click the DELETE SELECTED button.

4

The agent selected is removed from the list.

5

Click

6

Click the Apply Changes link located at the top right hand corner of the page, to commit the changes to the database.

2011 Copyright  IPitomy Communication, LLC

button to save the changes.

102 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Multicast Paging Group A Multicast Paging Group provides a way to page a large number of phones, while keeping the burden on the network and PBX to a minimum. NOTE: IPitomy recommends using multicast paging for groups of 10 or more phones that are paged frequently.

Figure 55 – Multicast Paging Groups Page

Figure 56 – Edit Page Group Window

2011 Copyright  IPitomy Communication, LLC

103 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide The following table describes the fields (parameters) on the Multicast Edit Paging Group window and the recommended settings. Sections/Fields

Description This is a name of the multicast paging group.

Name Local Number

This is the number that will be dialed to launch the multicast paging to the defined group. This is the unique 3-4 digit number.

Multicast Address

This should be a valid multicast IP for a Multicast Address. We recommend 225.5.5.5. You can use the same IP for each group, so long as you assign them different ports. This must be a valid, unused port Multicast Port.

Multicast Port

NOTE: This must be a port below 6535.

Time to Live

Time to Live is a counter that decreases by 1 each time a packet passes through a router. When the counter reaches 0, the packet is considered dead and will not pass to any other networks. This can be left blank or configured as needed for your particular install. NOTE: Leaving it blank the packet will not pass to another network.

Members

The Members section allows you to add the extensions to be paged within the group when a page is sent.

Add/Remove

The Add and Remove button allows you to add or remove members (extensions) from the paging group.

Create/Update

Depending on the process that is being performed, this button will appear (be labeled) as either Create or Update. This will create a new member or process the changes made.

Close Window

This link will close the Edit Page Group window and return you to the Ring Groups page. Table 40 – Multicast Paging Settings and Descriptions

The following section outlines the steps to add a new Multicast Paging Group.

Add Multicast Paging Group

STEPS: 1

Navigate to the DestinationsGroup page

2

Locate to the Multicast Paging Groups section (at the bottom of the page).

3

Click on the Add Groups button. The Edit Page Group page appears.

4

Enter the necessary information for the new paging group.

5

From the Members section of the Edit Page Group window, select the members (extensions) that you want to include in the paging group.

Use the CTRL or SHIFT button to select multiple or a range of extensions from the list.

2011 Copyright  IPitomy Communication, LLC

104 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide 6

Click on the ADD button to add the selected members to the group.

7

Click the CREATE button to save the changes. The “Group Created” message appears. Close the window (click on the “X”). The system returns you to the Ring Groups page.

8

Click the Apply Changes link located at the top right hand corner of the page, to commit the changes to the database

9

Re-boot the phones that correspond to extensions that were added to the Multicast Paging Group. Once all the phones have been re-booted, you will be able to utilize this feature by simply dialing the Local Number that was just created.

Edit Multicast Paging Group

STEPS: 1

Navigate to the DestinationsGroup page

2

Locate the Multicast Paging Groups section (at the bottom of the page).

3

Click on icon to the right of the Name of the paging group you want to update. The Edit Page Group page appears.

4

Enter the necessary information for the paging group.

5

Click the UPDATE button to save the changes. Close the window (click on the “X”). The system returns you to the Ring Groups page.

6

Click the Apply Changes link located at the top right hand corner of the page, to commit the changes to the database

7

Re-boot the phones for all the extensions that were involved in the Multicast Paging Group.

Delete Multicast Paging Group

STEPS: 1

Navigate to the DestinationsGroup page

2

Locate the Multicast Paging Groups section (at the bottom of the page).

3

Click on icon to the right of the Name of the paging group you want to delete. The group is removed from the Multicast Paging Group page.

4

Click the Apply Changes link located at the top right hand corner of the page, to commit the changes to the database

5

Re-boot the phones for all the extensions that were involved in the Multicast Paging Group which was deleted.

2011 Copyright  IPitomy Communication, LLC

105 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Live Queue Data The Live Queue Data page displays current call statistics for ACD queues. The page will refresh every 10 seconds, allowing a manager to monitor the activity in the queue as it happens.

Figure 57 – Ring Group Live Queue Data

Sections/Fields



Description In the queue selection box the Queue or Queues to be displayed can be selected. Use the Control key (Command on Mac) to select multiple queues for display. The Queue Statistics box has been reformatted in SW release 3.4.1 to allow its use on call center wall boards (large PC displays).



Each queue is encapsulated with a thin-line box. Queue statistics are colorcoded for quick orientation on wall boards. Since this data is presented in GUI format it can be easily resized to accommodate large displays. The top line of the queue display presents the Queue Name and the date. Statistics are a running total and will reset to zero whenever Apply Changes is clicked (as is the case of the screen capture above).

Time in Q Calls in Q Answered Abandoned

This is the average time that callers have waited in queue before being answered by a queue member/agent. This is the number of calls that are waiting in the queue. This is the number of calls answered by members/agent of this queue. This is the number of calls that have not been answered and the caller

2011 Copyright  IPitomy Communication, LLC

106 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide abandoned the queue.

Target Time

Displays the service level set for this ACD queue. The Service Level is the arbitrary time allocated by the queue administrator which is set as a gauge by which all calls should be answered.

% in Target

This is the percentage of answered calls measured against the service level. (The percentage of calls being answered within the set Target Time.)

At the right side of the Queue Statistics box the agents and queue members are listed. There are two maximum columns and the window will resize to accommodate all members and agents registered to this queue. Member/Agent status is available at a glance with color-codes as follows:



Red

=

In Use

Green

=

Idle (Logged In)

Yellow

=

Ringing

Gray

=

Unavailable (Not Logged In)

Orange

=

Paused

Also in the Member/Agent data are two numeral fields. The first number represents the Priority of this Member/Agent in this queue. The second number is the total calls taken by this Member/Agent. Table 41 – Live Queue Fields and Descriptions

Live Queue Data – Wallboard Software version 3.4.1 and above allows the use of call center wall boards with Live Call Queue. This function is facilitated using a special user name and password via Smart Personal Console.

Activate Live Call Queue Wallboard

STEPS: 1

Navigate to the PBX SetupGeneral page

2

Locate to the General Settings section (second section from the top).

3

Locate the SPC Reports User Password field (bottom of section)

4

It may be helpful to change this to a user-friendly password. If you change the password be sure to

and

.

5

Make a note of this password.

6

On the PC that will be used for the wallboard display, open a web browser and navigate to the IPitomy PBX login screen

2011 Copyright  IPitomy Communication, LLC

107 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide 7

Using the right side – Smart Personal Console (User Login) input the word “reports” as the user name and the password saved in step 3.

8

Click on

9

The CDR-Report page is opened. On this page is a button to select Live Queue.

.

10 Click on

.

11 The same display presented in PBX Administration is displayed. Simply select the group or groups that you wish to display on the wallboard. 12 Size this web page data output for the monitor in use by pressing and holding the Cntrl key (PC, Command key on Mac) and press “+” or “-“ until the data is sized as you wish.

2011 Copyright  IPitomy Communication, LLC

108 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Menus Menus direct callers to destinations within a business. A menu can route a caller to a destination once a number on a key-pad has been pressed. The menu prompt tells a caller what number to press to get to a desired destination. Menus can also be used to provide information to callers like driving directions, etc.

Figure 58 – Menus Page

2011 Copyright  IPitomy Communication, LLC

109 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide Edit Menu

Figure 59 – Edit Menus Page (with Control Menu Prompts open)

2011 Copyright  IPitomy Communication, LLC

110 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide Sections/Fields

Description Enter a name for the menu.

Name Menu Number (dial to go to menu)

This is the number of the menu. This number is used to access the menu from extensions – if necessary. The number must be a unique 3 or 4 digit number.

Default Menu Prompt

This is the recording that is active for callers who reach this menu when the Menu Prompt is set to default.

Active Menu Prompt

This function is enhanced in version 3.4.1. (Previously “Menu Prompt”.) As it indicates, this selection determines what prompt recording is heard by callers who reach this menu. Record this first under PBX SetupPrompts. The Copy… To… function allows you to place pre-recorded (and previously uploaded, see: PBX SetupPrompts) prompts into the available Prompts to be associated to this menu. Available “slots” are 1-5 where the user may then select 0-5, 0 being the default and 1-5 being those that are loaded. The user also has the ability to rerecord the prompts 1-5 via DTMF Administration access.

Control Menu Prompt: Copy … To …

Note: uploaded prompts are “copied” to the menu; therefore rerecorded prompts do not overwrite the original uploaded file. This is the destination that the menu will fail over to if the user does not press a digit in the allotted Response Time.

Fail Over Assign Menu Destinations

This list represents the destinations callers are routed to when pressing 0-9,*, #, and FAX. If a destination is set for FAX, the PBX will detect if a call inbound over an Analog or T1/PRI card is a fax while the prompt is playing, and will route calls to this destination if fax tone is detected.

Menu Destinations

Table 42 – Add/Edit Settings and Descriptions

Add Menu Settings

STEPS: 1. From the DestinationsMenus page, click the ADD menu button. The Edit Menu page appears. 2. Enter the information for the new Menu item and make necessary destination assignments.

3. Click

button to save the changes.

4. Click the Apply Changes link located at the top right hand corner of the page, to commit the changes to the database

2011 Copyright  IPitomy Communication, LLC

111 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Edit Menu Settings

STEPS: 1

From the DestinationsMenus page, locate the name of the Menu item you want to edit.

2

Click on icon to the right of the Name of the menu you want to update. The Edit Menu page appears.

3

Make the necessary updates to the menu setting then click

4

Click the Apply Changes link located at the top right hand corner of the page, to commit the changes to the database

button.

Delete Menu Settings

STEPS: 1

From the DestinationsMenus page, locate the name of the Menu item you want to edit.

2

Click on icon to the right of the Name of the menu you want to delete. The Menu name is removed from the Menu listing.

3

Click

4

Click the Apply Changes link located at the top right hand corner of the page, to commit the changes to the database.

2011 Copyright  IPitomy Communication, LLC

button.

112 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide Advanced Menu Settings

Figure 60 – Advanced Menu Settings Page

Sections/Fields

Description

Response Timeout

This is the number of seconds (0-60) the PBX will wait for digits to be dialed. If nothing is dialed in the allotted time, the menu will route the call to the Failover Destination. The minimum and default value is 4.

Digit Timeout

While entering digits, the PBX will wait this many seconds (1-20) after the last digit was entered to take any actions. Single decimal digits are permitted. The default value is 2.

Play the Greeting

This is the number of times the greeting will be played before the call is sent to the fail over destination. Default and minimum value is 1. This indicates whether you are able to dial local extensions from the menu. Default value is YES. Note: It is not necessary to designate leading digits for extensions. This setting alone indicates when digits collected should be compared to the available list of extensions.

Local extension dialing

This is the time in seconds that the PBX will wait when entering the menu before playing the prompt. The default is set to 2 seconds.

Prompt Padding

This enables the use of DTMF Menu Prompt Administration. When enabled the user may access the menu from a DTMF-enabled device and input the PIN to enter into Menu Prompt Administration Default value is No.

Enable Admin PIN

This is the PIN used to access DTMF Menu Prompt Administration. Default value is: .

Admin PIN

Table 43 – Advanced Settings and Description

2011 Copyright  IPitomy Communication, LLC

113 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Figure 61 – Remote Menu Announcement DTMF Admin Flow

2011 Copyright  IPitomy Communication, LLC

114 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Conferences The Conference Bridge allows groups of callers (large and small) to participate in the same call. An internal extension can dial the number direct to a conference; and outside callers can be routed to a conference by: being transferred from an existing call, being routed direct via a DID, or selecting an option from a menu. Each conference can be configured to require a PIN for entrance, or not.

Figure 62 – Conferences Page

Figure 63 - Edit Conference

2011 Copyright  IPitomy Communication, LLC

115 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Sections/Fields

Description Enter a name to distinguish this conference from others.

Name

Enter a unique 3-4 digits number for the conference.

Conference Number

If desired, a Prompt file can be played when entering the conference.

Intro Prompt Admin PIN

This is the Administrator personal identification number (PIN). This is a 3-4 character numeric field.

General PIN

This is the User personal identification number (PIN). This is a 3-4 character numeric field. If Enabled (checked), this prompts the user to record their name before entering the conference.

Announce on Enter

If Enabled (checked), users enter the conference in muted mode. The user can dial *1 to un-mute the themselves.

Enter Muted Optimize Talker Detection

If the DCM speech detection is triggering when no one is talking you can check this box to lessen the effect of background noise. Table 44 – Conference Settings and Descriptions

Add/Edit Conference

STEPS: 1

Navigate to DestinationsConferences.

2 3

Click the Add button to create a new Conference, or the button to edit an existing entry. Build the conference room to match your end users desires.

4

Click

5

Click the Apply Changes link located at the top right hand corner of the page, to commit the changes to the database.

2011 Copyright  IPitomy Communication, LLC

button.

116 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Conference Feature Codes The Feature Code section of the Conference page displays the key or key combinations that need to be pressed to activate or deactivate (toggling function) features for conferencing.

Figure 64 – Features Code Page

Sections/Fields Feature List Mute/Unmute

Description Pressing * will list all the features available while in the conference. Pressing *1 will allow you to toggle (switch) the mute state for yourself.

Lock/Unlock

Pressing *2 as the administrator will allow you to toggle (switch) whether new callers can join the conference.

Eject Last User

Pressing *3 as the administrator will allow you to eject the last caller who entered the conference.

Decrease Conference Volume Increase Conference Volume Decrease User Volume Increase User Volume Exit Menu

Pressing *4 will allow you to decrease the overall volume of the conference call. Pressing *6 will allow you to increase the overall volume of the conference call. Pressing *7 will decrease your call volume during the conference call. Pressing *9 will increase your call volume during the conference call. Pressing *8 will exit the features menu and return you to the conference call. Table 45 – Features Code Settings and Descriptions

2011 Copyright  IPitomy Communication, LLC

117 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Voicemail When an extension is created, a Voicemail box tied to that extension is automatically created. Voicemail boxes that do not have an extension associated with them are created and administered exclusively through Destinations Voicemail. There are three locations in the IP PBX that allow management of a voicemail box: • • •

Destinations Extensons – Under the Advanced Settings section, the basic settings for the mailbox can be configured. Destinations Voicemail – This area allows for total configuration of the voicemail box, including features like Broadcast and Cascading Message Notification. Smart Personal Console – Gives end users the ability to configure some mailbox settings.

Figure 65 – Edit Voicemail Box Settings Page

2011 Copyright  IPitomy Communication, LLC

118 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide Sections/Fields

Description

Mailbox

This is the mailbox number, which must be a unique 3 or 4 digit number.

Name

This is the name of the voicemail box.

Password

This is the password to access the voicemail messages. Only numbers are allowed.

User E-mail

This is the email address associated with this mailbox. Defines whether the PBX will send an email to the user informing them they have a new message. An audio file (.Wav) of the message will be attached.

Attach to Email

YES = send email with attachment. NO = do not send an email. N/A = use the system wide default defined under PBX Setup Voicemail. Defines if the voicemail message will be deleted from the PBX after the email has been sent. YES = delete message after it has been emailed.

Delete After Emailing

NO = do NOT delete message after emailing. N/A = use the system wide default defined under PBX Setup Voicemail. Note: This feature should not be enable at the same time as Turn Old After Emailing. Defines if the voicemail message will be sent from the NEW folder to the OLD folder after emailing.

Turn Old After Emailing

YES = move message to Old messages folder after emailing. NO = leave the message in the NEW messages folder after emailing. Note: This feature should not be enable at the same time as Delete After Emailing. Defines if the Caller ID will be played prior to playback of the message.

Say Caller ID

YES = state caller id prior to message content playback. NO = do NOT state caller id prior to message content playback. N/A = use the system wide default defined under PBX Setup Voicemail. Defines if the caller is permitted to review and take action on the message they leave.

Allow Review

YES = allow callers to review and re-record the message they left. NO = do not allow callers to re-record their message. N/A = use the system wide default defined under PBX Setup Voicemail. Defines if the caller is permitted to press “0” to reach the mailbox operator while leaving a voicemail message.

Allow Operator

YES = allow dial 0 while listening to mailbox greeting. NO = disallow dialing 0 while listening to mailbox greeting N/A = use the system wide default defined under PBX Setup Voicemail.

2011 Copyright  IPitomy Communication, LLC

119 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide Defines if the system will play caller ID and time of call prior to playback of the message. Play Envelope Message

YES = play message details prior to playback of message contents NO = do not play message details prior to playback of contents. N/A = use the system wide default defined under PBX Setup Voicemail.

Auto Delete VoicemaiI In

Define the number of days in which voicemail messages are to be automatically deleted from a mailbox. If this is set to “0” (zero) the voicemail message will never expire.

Allow Dial Out Access

This permits the user to dial out from voicemail.

Exclude from Directory

This indicates whether to exclude the extension paired with this mailbox from the directory.

Mailbox Operator

Defines where to route a calller if they press “0” (zero) while listening to your mailbox greeting. Set this to None to use System Default from value defined at PBXSetup General.

Mailbox Exit Destination

If a caller remains on the line or presses # after leaving a message in this voice mailbox, this is where they will be routed. Set this to None to use System Default from PBXSetup General.

Broadcast Messages

If this setting is configured, messages that are directly left in this box are broadcasted to the boxes that are added to the list. Note that messages forwarded to this box are not broadcast.

Cascading Message Notification

If enabled, the Cascading Message Notification feature will be activated, allowing you to configure the system to call a single or group of phone numbers when a new voicemail message has been received. Table 46 - Voice Mailbox Settings and Descriptions

Add Voicemail Settings The following outlines the steps to create a stand alone voicemail box.

STEPS: 1

From the Destination Voicemail page, click the Add Mailbox button located at the top left corner of the page.

2

The Edit Voicemail Box Settings page is displayed. Using the table of parameters and descriptions above, configure the voicemail box to meet your business requirements.

3

Click button to save the changes. The system returns you to the Edit Voicemail Box page.

4

Click the Apply Changes link located at the top right hand corner of the page, to commit the changes to the database.

2011 Copyright  IPitomy Communication, LLC

120 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Edit Voicemail Settings The following outlines the steps to modify voicemail parameters.

STEPS: 1

From the Voicemail Box Setup page, locate the mailbox that you want to update.

2

Click the

3

The Edit Voicemail Box Settings page is displayed. Make the necessary changes to the extension information.

4

Click button to save the changes. The system returns you to the Edit Voicemail Box page.

icon to the right of the Mailbox Name.

Clear Voicemail Messages The following outlines the steps to clear a voicemail box of all messages and greetings.

STEPS: 1

From the Voicemail Box Setup page, locate the mailbox that you want to clear messages from. Click the

icon to the right of the Mailbox Name.

2

The messages from that mailbox will be deleted.

3

button to save the changes. The system returns you to the Edit Click Voicemail Box page.

4

Click the Apply Changes link located on the right hand corner of the page, to commit the changes to the database.

Delete Voicemail Box

STEPS: 1

From the Voicemail Box Setup page, locate the mailbox that you want delete.

2

Click on

3

The mailbox is removed from the Mailbox listing.

4

Click button to save the changes. The system returns you to the Edit Voicemail Box page.

5

Click the Apply Changes link located on the right hand corner of the page, to commit the changes to the database.

icon to the right of the Mailbox Name of the menu you want to delete.

2011 Copyright  IPitomy Communication, LLC

121 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Broadcast Message – Add

STEPS: 1

From the Edit Voicemail Box Settings page is displayed. Scroll to the Broadcast Messages section.

2

Select the mailbox from the left list box then click the Add button. The item selected will populate the list on the right.

CTRL and Shift clicking is supported to select multiple mailboxes at once.

3

Click button to save the changes. The system returns you to the Edit Voicemail Box page.

4

Click the Apply Changes link located at the top right hand corner of the page, to commit the changes to the database.

Broadcast Message – Remove

STEPS: 1

From the Edit Voicemail Box Settings page is displayed. Scroll to the Broadcast Messages section.

2

Select the mailbox from the right list box then click the Remove button. The item selected will be removed from the list.

CTRL and Shift clicking is supported to select multiple mailboxes at once.

3

Click button to save the changes. The system returns you to the Edit Voicemail Box page.

4

Click the Apply Changes link located at the top right hand corner of the page, to commit the changes to the database.

5

Click the Apply Changes link located on the right hand corner of the page, to commit the changes to the database.

Cascading Message Notification Cascading Message Notification works along the same principle as FollowMe, but pertains to voicemail messages. When configured, if an extension gets a new VM, the PBX can call a variety of numbers, in the order defined, to inform the user of the message. Note: Once the call is answered, the user will have the ability to listen to their message from their

phone, or to refuse the call. Until the voicemail box has its new messages cleared, the system will continue to call out when the Notification Interval is met. 2011 Copyright  IPitomy Communication, LLC

122 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Set Cascading Messages

STEPS: 1

Navigate to the Edit Voicemail Box Settings page.

2

Scroll to the Cascading Message Notification section.

3

Select Disable to turn the notification feature OFF. Select Enabled to turn the notification feature ON.

4

Click button to save the changes. The system returns you to the Edit Voicemail Box page.

5

Click the Apply Changes link located at the top right hand corner of the page, to commit the changes to the database.

Setting Cascading Interval

STEPS: 1

Navigate to PBX Setup General.

2

Locate the Cascading Voicemail Notification Interval, set the value to the desired number of minutes, the PBX will check for new emails and make calls to notify when the interval passes. Default is 5 minutes.

3

Click the

4

Cick the Apply Changes link located at the top right hand corner of the page, to commit the changes to the database.

2011 Copyright  IPitomy Communication, LLC

button to save the changes.

123 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Configure Contact Numbers for Cascading Message Notification

Figure 66 – Notification Settings / Voicemail Box Page

2011 Copyright  IPitomy Communication, LLC

124 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Sections/Fields Add X seconds to total search time

Description This allows you to configure how many seconds the system will spend searching for the called party. Default is 12 seconds.

Introduction Prompt

Introduction Prompt plays “You have new messages” after you answer the call. This can be set to any custom prompt you have recorded on the system.

Options Prompt

Options Prompt plays “Please enter your voicemail password, or 2 to reject this call” after you answer the call. This can be set to any custom prompt you have recorded on the system.

Outbound Context

Outbound Context gets set to an extension number, and will use that extension’s Class of Service when making outbound calls.

Numbers

Configure the numbers you wish to be called when a VM message is received. The calls will be made in order, with 1 being the highest priority and 20 the lowest. You must check the Use column for each number to be considered active. If you wish to delete a number, click the

button then save and exit.

Table 47 – Notification and Voicemail Box Settings and Descriptions

STEPS: 1

From the DestinationsVoicemail page, click the pencil edit.

2

Scroll to the Cascading Message Notification section and click the Contact Numbers button (Cascading Message Notification needs to be enabled)

3

The Notification Settings / Voicemail Box window will appear. Set the parameters based on the description of the values provided in the table above.

4

Click the

5

Click the Apply Changes link located at the top right hand corner of the page, to commit the changes to the database.

2011 Copyright  IPitomy Communication, LLC

of the mailbox you wish to

button to save the changes.

125 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Schedules

Figure 67 – Edit Schedule and Holidays Page

Sections/Fields Name Hours of Operation

Description This is the name that is associated with the schedule. Define the start and end time for the hours that will be considered Operational hours This is the assigned Destination where the calls will go during the schedule’s hours of operation.

In Hours Destination

If “Apply Forwarding Settings” is enabled (checked), the destination’s call forward settings. The items in the drop-down listing are the configured Destinations in your PBX system

2011 Copyright  IPitomy Communication, LLC

126 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide This is the assigned Destination where the calls will go when it is received outside the schedule’s hours of operation. Outside of Hours Destination

If “Apply Forwarding Settings” is enabled (checked), to use the destination’s call forward settings. The items in the drop-down listing are the configured Destinations in your PBX system. Define the hours allocated for lunch for a schedule. Calls received during this time will be sent to the Lunch Hours Destination.

Lunch Hours

This is the assigned Destination where the calls will go when it is received during the allocated Lunch Hours. Lunch Hours Destination

If “Apply Forwarding Settings” is enabled (checked), to use the destination’s call forward settings. The items in the drop-down listing are the configured Destinations in your PBX system. Holiday Name – This is the name associated with this holiday schedule. Start – This is the start date and time for this holiday schedule. (The year is defaulted to the current year.)

Holidays

End – This is the end date and time (expiration) for this holiday schedule. (The year is defaulted to the current year.) Destination – This is the assigned Destination where calls will be routed when it is received during the holiday schedule. Table 48 – Edit Schedule Settings and Descriptions

Add Schedule STEPS: 1

From the DestinationsSchedules page, click on the ADD Schedule button.

2

The Edit Schedule Switch page appears.

3

Enter the settings for the new schedule.

4

Click the

5

Click the Apply Changes link located at the top right hand corner of the page, to commit the changes to the database

button to save the changes.

Add Holiday to Schedule

STEPS: 1

From the DestinationsSchedules Edit Schedule Switch page, scroll down to the Holidays section of the page.

2

Enter the dates and times for the new holiday schedule. Click the Add button to add the new holiday schedule.

3

Click on the newly added holiday, select a destination from the Destination dropdown and click Set

2011 Copyright  IPitomy Communication, LLC

127 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide 4

Click the

5

Click the Apply Changes link located at the top right hand corner of the page, to commit the changes to the database

button to save the changes.

Remove Holiday from Schedule

STEPS: 1

From the DestinationsSchedulesEdit Schedule Switch page, scroll down to the Holidays section of the page.

2

Select the holiday (appearing in the list) that you want to remove. Click the Remove button to delete the holiday schedule. The item in the Holiday list is removed.

3

Click the

4

Click the Apply Changes link located at the top right hand corner of the page, to commit the changes to the database

button to save the changes.

Edit Schedule STEPS: 1

From the DestinationsSchedules page, locate the schedule name that you want to edit.

2

icon to the right of the Name of the schedule you want to update. The Edit Click on Schedule Switch window appears.

3

Edit the necessary parameters to configure the schedule.

4

Click the

5

Click the Apply Changes link located at the top right hand corner of the page, to commit the changes to the database

button to save the changes.

Delete Schedule STEPS: 1

From the DestinationsSchedule page, locate to the Schedule Name from the listing that you want to delete.

2

Click on icon to the right of the Name of the schedule you want to delete. The schedule is removed from the listing page.

3

Click the

4

Click the Apply Changes link located at the top right hand corner of the page, to commit the changes to the database.

2011 Copyright  IPitomy Communication, LLC

button to save the changes.

128 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Branch Offices Branch Offices provide a powerful tool for interconnecting PBX Systems. Through Branch Offices you can create a network of systems where dialing phones on remote systems is as easy as dialing local extensions. You can route calls inbound to a destination on any branched PBX, and outbound through the trunks of other systems networked in this way. Branch office extensions can even participate in ring groups.

Figure 68 – Sample Branch Office Networking

!

IMPORTANT: Branch Offices communicate using IAX2 protocol over Port 4569. Refer to the Port Forwarding Configuration Table earlier in this manual for more information.

2011 Copyright  IPitomy Communication, LLC

129 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Figure 69 – Edit Branch Office Page

2011 Copyright  IPitomy Communication, LLC

130 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Sections/Fields

Description The name that is associated with the branch office. Both sites involved in the Branch Office connection must use the same Name.

Name

NOTE: This field will not allow spaces in the name. It must be all one word. Symbols can be used (i.e. underscore “_” dashes “-”, etc.) can be used in place of spaces.

Host

Enter the static IP of the system your PBX is connecting to. If they do not have a static IP address, enter the word dynamic.

Dial Prefix

The dial prefix must be an asterisk, plus two numbers (ie. *22). This prefix must be dialed to reach any destination on another PBX that has not been entered as a Branch Extension.

Password

This is the password that will allow access to the PBX. Both sites involved in the Branch Office connection must use the same Password. YES= to require that the branch office register with the PBX system. Only used if the Host is set to dynamic.

Register

NO = does not require that the branch office register with the PBX system. YES = Branched PBXs are able to dial calls out your PBXs trunks.

Enable Trunking

NO = Branched PBXs are not able to dial calls out your PBXs trunks.

Enable Multisite Manager Connection:

Defines if Multi-Site Call Manager functionality is enabled. This feature requires a license from IPitomy to be functional.

Qualify Enable IAX2 Trunking

The time in milliseconds that the PBX should check that the branch office is still online. Setting this to zero may increase Branch Office stability. Indicates whether to use IAX trunking. If enabled (YES), this setting can help eliminate packet overhead by cutting the cost of continuous communication.

Allow Codecs:

Defines what codecs this branch office can use for calls. Priority for codecs are defined from top to bottom.

Class of Service:

Allows for individual Branch Offices to use different COS. Setting to None will follow the default Branch Office COS defined under PBX SetupGeneral. Table 49 – Branch Office Settings and Descriptions

2011 Copyright  IPitomy Communication, LLC

131 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Figure 70 – Branch Offices Page

Configuring Office 1 STEPS: 1

Click on Destinations Branch Offices. The Branch Offices page is displayed.

2

Click on the ADD office button. The Edit Branch Office page appears.

3

Give a unique NAME for the connection. The name should only contain alpha-numeric characters and no spaces. It should be ONE WORD ONLY.

4

Enter the External IP of the PBX in the Host field.

5

Enter a unique DIALING PREFIX of an asterisk followed by two numbers.

6

Give a unique PASSWORD for the connection.

7

Select NO for REGISTER (Note: that registration is not required if host is known).

8

Configure Enable Trunking as needed.

9

Configure Enable Multisite Manager Connection as needed.

10 Set QUALIFY at 0. 11 Configure Enable IAX2 Trunking as needed.

2011 Copyright  IPitomy Communication, LLC

132 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide 12 Click the

button to save the changes.

13 Click the Apply Changes link located at the top right hand corner of the page, to commit the changes to the database

Configuring Office 2 STEPS: 1

Click on Destinations Branch Offices. The Branch Offices page is displayed.

2

Click on the ADD Office button. The Edit Branch Office page appears.

3

Enter a name in the NAME field that matches that given to the Office 1 PBX. The name should only contain alpha-numeric characters and no spaces. It should be ONE WORD ONLY.

4

Enter an external IP address or domain corresponding to the IP of the main office PBX in the HOST field.

5

Enter a UNIQUE dialing prefix for the extensions connected to the Office 2 PBX.

6

The PASSWORD for Branch Office 2 needs to be the same as the one assigned in the Branch Office 1 PBX.

7

Select NO for REGISTER.

8

Configure Enable Trunking as needed.

9

Configure Enable Multisite Manager Connection as needed.

10 Set QUALIFY at 0. 11 Configure Enable IAX2 Trunking as needed.

12 Click the

button to save the changes.

13 Click the Apply Changes link located at the top right hand corner of the page, to commit the changes to the database

To setup additional Branch Offices in the PBX, use the steps outlined above. Keep in mind to use the same logic (pattern) and make sure that the dialing prefix is unique to each office.

2011 Copyright  IPitomy Communication, LLC

133 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Edit Branch Office STEPS: 1

From the DestinationsBranch Office page, locate the schedule name that you want to edit.

2

Click on icon to the right of the Name of the Branch Office you want to update. The Edit Branch Office page appears.

3

Edit the necessary parameters to configure the branch office.

4

Click the

5

Click the Apply Changes link located at the top right hand corner of the page, to commit the changes to the database

button to save the changes.

Delete Branch Office STEPS: 1

From the DestinationsBranch Offices page, locate to the Name from the Branch Office listing that you want to remove.

2

Click on icon to the right of the Name of the Branch Office you want to delete. The Branch Office is removed from the listing page.

3

Click the

4

Click the Apply Changes link located at the top right hand corner of the page, to commit the changes to the database

button to save the changes.

Branch Extensions Branch Extensions are created through the add extension field at the bottom of the branch office edit page. Branch extensions can be dialed directly without a prefix, provided that these extensions are properly configured on the PBX for which the branch extensions are defined. Branch extensions will appear in call routing drop down lists throughout the system after they are created. If needed, you can add Ring Group and Menu numbers as Branch Extensions.

2011 Copyright  IPitomy Communication, LLC

134 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Configuring Office 2 with Branch Extensions

Figure 71 – Branch Office Extension Section

STEPS: 1

Click on DestinationsBranch Offices. The Branch Offices page appears.

2

Click on the Branch Office connection (Name) assigned to Office 1.

3

Assuming Office 1 has extension numbers 100 thru 110, enter the numbers 100 to 110 in the field above the Add button then click ADD. You will enter (add) each extension one at a time. Note: Using the format X-Y will add all extensions in the specified range.

4

If the extension number is valid (not already in use), the new extension will appear in the list of Branch Extensions.

5

Click the

6

Click the Apply Changes link located at the top right hand corner of the page, to commit the changes to the database.

7

Verify the new extension by calling the number from phones located (registered) at Branch Office 2.

button to save the changes.

To place a call from one Branch Office to another simply dial the prefix that was assigned to that locations PBX + the extension of the user trying to be reached at the other office. This same easy concept works for transferring calls from one Branch Office to another. Or, if you have the extension configured as a Branch Extension on your PBX, you can simply dial the extension number and it will be automatically routed to the branch.

2011 Copyright  IPitomy Communication, LLC

135 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide View Branch Office Extensions

Figure 72 – Show Extensions Page

STEPS: 1

From the DestinationsBranch Office page, click on the Show Extensions button located at the top of the Branch Office list page.

2

A popup window appears displaying all the extension information for each Branch Office that is currently in the system.

3

Click on the “X” to close the popup window.

2011 Copyright  IPitomy Communication, LLC

136 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Call Routing Call routing sends callers to specific inbound destinations within the system, and routing outbound callers over specific outbound routes like local, long distance, international and emergency.

Incoming Call Routing

Figure 73 – Incoming Call Routing Page

2011 Copyright  IPitomy Communication, LLC

137 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide This table describes the parameters that can be set for incoming calls. Calls can be routed to destinations and you can also enable (set) the time parameter when the calls will get sent to their defined route. Sections/Fields

Description

Disable Day/Night Mode Button

The PBX system defaults to Day/Night Mode Disabled. To toggle between Enabled/Disabled settings for the Day/Night Mode setting. When enabled the Edit Night and Hours button will appear which will allow you to configure the night destinations and hour parameters.

Edit Night/Day Button

Toggles between Day/Night Mode settings. When selected, it will change the Displaying field to either “Day Mode” or “Night Mode”, allowing you to configure the destination for calls when in and out of hours. Allows you to edit the hours for the incoming calls to routing.

Edit Hours

!

Edit DID Caller ID

IMPORTANT: If you enable day night mode service you must populate the system hours schedule otherwise all calls will be routed to the night destinations.

Allows you to edit CID information for incoming calls based on DID. If you wish to retain the original CID information as well as display the override info, be sure to check the box for Prepend. Each provider will display in a gray box. DIDs for each provider will display beneath the gray box in white. If a DID destination is set to None, it will follow the settings for the provider itself. If a provider destination is set to None, calls will route to the Default Incoming Destination.

Providers

This button allows for configuration of destination specific settings. Groups: Allows you to define a priority, increasing or decreasing the calls importance in the queue. The higher the number, the higher the priority. Extension: Allows you to define a group of numbers that will be dialed once the call has been answered. Typically used when connecting an extension to a fax server that routes faxes to people based on the digits read at the time of answering the call. Table 50 – Incoming Call Routing Settings and Descriptions

Set Default Incoming Destination

STEPS: 1

From the Call RoutingIncoming Routing page, go to the Default Incoming Destination section.

2

Select the desired Destination category from the first drop-down list, then select the specific destination from the second drop-down list.

3

Click the

4

Click the Apply Changes link located at the top right hand corner of the page, to commit the changes to the database.

2011 Copyright  IPitomy Communication, LLC

button to save the changes.

138 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide Set Provider Trunk Incoming Destination 1

From the Call RoutingIncoming Routing page, go to the section that corresponds to either your SIP Provider or Channel Group name.

2

Select the desired Destination category from the first drop-down list, then select the specific destination from the second drop-down list.

3

Repeat step 2 for all other providers. Any provider that can follow the Default Incoming Destination can be left as None.

4

Once you have made the necessary changes, click the the changes.

5

Click the Apply Changes link located at the top right hand corner of the page, to commit the changes to the database.

button to save

Enable/Disable Day/Night Mode The following section outlines steps to enable or disable the Day/Night Mode for Incoming Calls.

STEPS: 1

From the Call RoutingIncoming Routing page, click on the Enable/Disable Day/Night Mode button located at the top of the page.

2

The Day/Night Mode changes either Enabled or Disabled (depending on its previous setting).

3

Once you have set the parameter to the desired mode, click save the changes.

4

Click the Apply Changes link located at the top right hand corner of the page, to commit the changes to the database.

button to

Switch Day/Night Mode This feature allows you to change whether you are editing the Day destinations or the Night destinations for incoming calls. The following section outlines the steps to switch or toggle to/from night or day.

STEPS: 1

From the Call RoutingIncoming Routing page, click on the Edit Night or Edit Day button located at the top of the page.

2

The Displays field changes either Day Mode or Night Mode (depending on its previous setting).

3

Modify the destinations for whichever mode you are working with, then click button to save the changes.

4

Click the Apply Changes link located at the top right hand corner of the page, to commit the changes to the database.

2011 Copyright  IPitomy Communication, LLC

139 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide Edit Hours

STEPS: 1

From the Call RoutingIncoming Routing page, click on the Edit Hours button located at the top of the page, which will open the schedule page for Day/Night mode.

2

Set the hour parameters for the incoming route to meet the business requirements. See the previous section pertaining to Schedules for more details.

3

Click

4

Click the Apply Changes link located at the top right hand corner of the page, to commit the changes to the database.

button to save the changes.

Edit Incoming Caller DID If you want a particular DID to display the override CID information followed by the original inbound CID information, be sure to check the box for Prepend, otherwise the original CID information will be lost.

Figure 74 – Incoming Routing Edit Incoming DID CID Page

STEPS: 1

From the Call RoutingIncoming Routing page, click on the Edit DID Caller ID button located at the top of the page.

2

A list of existing DID numbers is displayed. Enter Caller ID Name and corresponding Caller ID Number for the desired DID Number.

3

Enable Prepend for each by checking the box, if desired.

4

Once you have made the necessary changes to the DID numbers, click the button to save the changes.

5

Click the Apply Changes link located at the top right hand corner of the page, to commit the changes to the database.

2011 Copyright  IPitomy Communication, LLC

140 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide Outgoing Call Routing By default, the PBX has five dialing routes built and included in the System Default Class of Service. These routes are 7 Digit, 10 Digit, 11 Digit, International, and Emergency, and should handle the normal day to day calling needed on a PBX. Once you have configured trunks on the PBX, you must add them to whichever dialing routes you wish to use those trunks. IPitomy advises you add ALL available trunks to the Emergency route, and to check with the end user before adding trunks to the International dialing route. Some users may require specific dialing routes to be built to meet their needs.

!

IMPORTANT: Please keep in mind that all new routes need to be added to a Class of Service before the route can be used.

Sections/Fields Add Route Add Custom Route

Class of Service

7 Digit Local Dialing 10 Digit Dialing 1+ Dialing (11 Digit) International Emergency

Description Click this button to create a new Outbound Dialing Route. Advanced feature only available through licensing. Contact IPitomy for more information. A Class of Service (COS) pertains to a group of outbound dialing routes. You can define a specific COS for an extension or branch office, limiting which routes are usable by those entities. Select a specific COS from the dropdown to view the routes included for that COS. Click on the blue words Class of Service to create, modify, or delete a Class of Service. By default this route looks for a pattern of any number 7 digits long. By default this route looks for a pattern of any number 10 digits long. By default this looks for a pattern of numbers that start with a 1 and is 11 digits long. By default this looks for a pattern of numbers that start with 011 that is between 4 and 15 digits long. By default, this looks for the specific pattern of 911. Table 51 - Outbound Routing Page Descriptions

2011 Copyright  IPitomy Communication, LLC

141 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Figure 75 – Outgoing Routing Page

2011 Copyright  IPitomy Communication, LLC

142 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Figure 76 – Add New Outgoing Route Page

!

IMPORTANT: Please keep in mind that all new routes need to be added to a Class of Service before the route can be used. Subroutes are automatically added under the parent route they use.

2011 Copyright  IPitomy Communication, LLC

143 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide Sections/Fields Route Name Route Type

Description This is the name associated with the outgoing route. Set to New Route for a brand new dialing route, or select an existing route to build a subroute. Defines what type of digit pattern will match the route. Acceptable entries are: Numbers

Start Pattern

X = Any number N = Any number, excluding 1 and 0

Digits

Length of the pattern that will match the route. Defines if the number dialed has to exactly match the pattern length defined under Digits.

Exact Length

Yes – Does need to match exactly. No – Does not need to match exactly.

Subroute Digits

How many digits of the number dialed to read for comparison to any subroutes that may be built for this route.

Subroute Offset

How many digits of the number dialed to skip before starting to read Subroute Digits

Number

When building a subroute off of an existing Outbound Dialing Route, this is the number that will match the subroute digits of the parent outbound route. For example, the 11 digit dialing route reads the area code for subroute digits by default. Here, you would enter the area code that needs to be subrouted. In order to dial outbound from a dialing route, you need to define what trunks it will use. Add – Use this button to add the trunk selected from the dropdown to the route. Delete – This button allows you to delete the trunk selected from the route. Up – Highlight a trunk and click this button to move it up the list, and in priority.

Trunks

Dn – Highlight a trunk and click this button to move it down the list, and in priority. Strip Digits – This indicates whether the PBX will strip any digits before sending the call out a particular Trunk. This is set per trunk. Prefix Digits – Defines the digits to be prepended to the dialed number before sending the call out a particular Trunk. This is set per trunk.

2011 Copyright  IPitomy Communication, LLC

144 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide In addition to the Extension and Trunk, Caller ID (CID) override can be set on a per route basis. Each outbound route can be configured to override the CID name and/or CID number that is sent when dialing out each trunk in the route. Each outbound route also has control over whether extensions with Ext CID Override configured are able to send their CID information. Disable Ext CID Override - Set to “YES” if you want to disable the CID override for the outgoing route, including Extension CID settings.

CID Override for Outbound Route Parameters

Force Use PSTN CID – New in version: 3.4.1, it is now possible to deliver the CID received on PSTN inbound calls out on calls being transferred outbound. This feature is subject to the ability of the provider associated to the outbound call. This provider must be able to allow substitution of CID. Set to “YES” if you want to send the received CID with a call transferred outbound.. Override Default CID (name) - Set to “YES” if you want to enable custom Name CID override for the outgoing route. Override CID Name – If the Override Default CID (name) is set to “YES”, enter the new CID override name for the outgoing route. Override Default CID (number) - Set to “YES” if you want to enable custom Number Default CID override for the outgoing route. Override CID Number – If the Override Default name is set to “YES”, enter the new CID override number for the outgoing route. Table 52 – Outbound Route Settings and Descriptions

Add Outgoing Route

STEPS: 1

From the Call RoutingOutgoing Routing page, click on the Add Route button located at the top of the page. The Edit Outbound Route page appears.

2

Enter the parameters to configure the outbound call route.

3

Once you have entered all the necessary information, click the save the changes.

4

Add the new route to any Class of Service it will be used with.

5

Click the Apply Changes link located at the top right hand corner of the page, to commit the changes to the database.

button to

Edit Outgoing Route

STEPS: 1

From the Call RoutingOutgoing Routing page, locate the Outbound Route name that you want to edit.

2

Click on icon to the right of the Route you want to update. The Edit Outbound Route page appears.

3

Edit the necessary parameters to configure the outbound route.

2011 Copyright  IPitomy Communication, LLC

145 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide 4

Click the

5

Click the Apply Changes link located at the top right hand corner of the page, to commit the changes to the database.

button to save the changes.

Delete Outgoing Route

STEPS: 1

From the Call RoutingOutgoing Routing page, locate to the Route Name from the Route listing that you want to delete.

2

Click on icon to the right of the Route Name you want to delete. The Route is removed from the listing page.

3

Click the

4

Click the Apply Changes link located at the top right hand corner of the page, to commit the changes to the database.

2011 Copyright  IPitomy Communication, LLC

button to save the changes.

146 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Class of Service A Class of Services is used to define which outbound dialing routes a given feature can use. By clicking the blue words Class of Service on the Outgoing routing page, you will be able to delete, create, clone, and populate your Class of Service with the desired outbound routes.

Figure 77 - Class of Service

Sections/Fields Class of Service

Description Use the drop down box to view Class of service. You can then take actions pertaining to that COS.

Rename

Enter a new name in the far left text field, then click the Rename button to change the name of the COS currently being viewed.

Create New

Allows you to create a new, blank, COS. Name the COS in the text field to the left of the Create New button, then click the button to create.

Clone

Add

Select from the drop down the COS you wish to clone. Enter a name in the field to the left of the Create New button. When you click the Clone button, a new COS will be created with the new name which will be populated with the routes of the original COS. Clicking the Add button will add the route displayed in the dropdown to the COS that is currently being viewed.

2011 Copyright  IPitomy Communication, LLC

147 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide Clicking this button in the gray bar will delete the COS. Clicking this button next to a route will delete that route from the viewed COS.

Outgoing Call Routing This section demonstrates, by example, some of the common configurations used with Outbound Routing.

Configure Block Calls Subroutes In this example, your customers want to block their users from dialing 1-900 numbers. To achieve this, you will need to create a subroute and configure it using the specifications below.

Figure 78 – Blocking Dialing 1-900

Sections/Fields Route Name Route Type Number

Description Enter a meaningful name for the outbound route. In this case you may want to call it “Block 900”. Select 1+ Dialing, as this will be a subroute 900, since the default 1+ Dialing route skips the 1 that is dialed, and reads the next 3 digits for subroutes

2011 Copyright  IPitomy Communication, LLC

148 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide Trunks

None should be added, as without a trunk to dial out, any 1-900 number will be dead in the system. Table 53 – Block 1900 Outbound Call Configuration

Configure Least Cost Routing Subroutes In this example, the end user has multiple providers in different regions, and wants dialed calls to use the most cost effective trunk when dialing out. The default 1+ (11 Digit) dialing route has Subroute Offset = 1 (ignores the first digit dialed, this case being the 1 for a long distance number) and Subroute Digits = 3 (after ignoring the first digit from subroute offset, this reads the next 3 digits (area code) in the dialed string and compares them to any subroutes created). The subroute that will be built specifically routes calls dialed to the 941 area code through a different, more cost efficient trunk.

Figure 79 – Least Cost Routing Example

Sections/Fields

Description

Route Name

Enter a meaningful name for the outbound route. In this case you may want to call it “Sarasota Subroute”.

Route Type

Select the 1+ Dialing as the route type, as this will be a subroute of that dialing route.

2011 Copyright  IPitomy Communication, LLC

149 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide Enter 941 as this is the area code for the

Number

Add the trunks that will call this particular subroute in the most cost effective manner.

Trunks

Table 54 – Least Cost Outbound Call Subroute Configuration

!

IMPORTANT: The normal 11 Digit route is using analog 1 and analog 2 for trunks, while the 941 sub-route uses a trunk that can dial locally to Sarasota without accruing long distance charges.

Configure Information (411/1411) Subroute If you would like callers to have the ability to use Information Service provided by your carrier then you must configure the route. If they must dial 411 to get information then you will need to configure a route for 411. To do this configure a route as below,

Figure 80 – Information (411) Subroute Setting

Sections/Fields Route Name Route Type

Description Enter a meaningful name for the outbound route. In this case you may want to call it “Information”. Select New Route, as this will not be a sub-route of any other route.

2011 Copyright  IPitomy Communication, LLC

150 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide Start Pattern

Enter the start pattern of as the code your provider uses for information, in this case “411”

Digits

Enter the length of the code your provider uses for information, in this case “3” Set the exact length to “YES”

Exact Length

Set the Subroute digits to “-1” (minus 1).

Subroute Digits

Set the Subroute offset to “0”

Subroute Offset

Add any trunks that are appropriate for dialing Information with the code created.

Trunks

Table 55 – Information (411) Subroute Configuration

IMPORTANT: Please keep in mind that all new routes need to be added to a Class of Service before the route can be used. Subroutes are automatically added under the parent route they use.

!

PBX Setup PBX setup is used by a System Administrator to manage system-specific and system-wide settings. Typically these pages will be visited once during installation, and then won’t be changed in the future.

General System Setup While not visited often, the General settings page pertains to some core PBX components, like administrator Username and Password, Time Settings, System Operator, Mailbox Exit Destination, Directory Type, Autoprovisioning, and Security Settings.

Admin Settings Section

Figure 81 – PBX Admin Settings Section

Sections/Fields Admin User Name Admin Password

Description The administrator user name for the PBX system, default is pbxadmin The administrator password for the PBX system, default is ipitomy. Once installed, we recommend you change this to a strong password.

2011 Copyright  IPitomy Communication, LLC

151 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide Re-type Admin Password

This requires that you re-enter the password to confirm that they match.

Admin Email Address

This is the email address where administrative alerts will be sent. Table 56 – PBX Admin Settings Parameters and Descriptions

Edit Admin Settings

STEPS: 1

From the PBX Setup General System Setup page, locate the Admin Settings section.

2

Enter the administrative information required.

3

Click the

4

Click the Apply Changes link located at the top right hand corner of the page, to commit the changes to the database.

button to save the changes.

General Settings Section

Figure 82 – PBX General Settings Section

Sections/Fields

2011 Copyright  IPitomy Communication, LLC

Description

152 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide This is the default destination that callers will go to when pressing ‘0’ while in a voicemail box, if Allow Operator is enabled on the voicemail box. Additionally, if an extension dials zero, this will be where they are directed.

System Operator

Mailbox Exit Destination

This is the default destination for a caller if they press ‘#‘after leaving a voicemail message.

Directory Type

This determines if the name directory search will use the first or last name.

Cascading Voicemail Notification Interval

This is the frequency with which the PBX will check and send out cascading message notifications.

Default Class of Service

Defines what COS each newly created extension will use unless it is changed.

Branch Class of Service

This is the default COS for a Branch Office using Branch Office Trunking.

Internal Distinctive Ring

This is the type of ring that will be used for internal calls.

5xi Paging Fix

Enabled (set to YES) this parameter only if IPitomy’s technical support personnel advises.

Park Timeout

This is how long the PBX will wait before timing out to an extension that has a parked call, which if unanswered will failover to the System Operator. Default value is 180 seconds.

Feature Digit Timeout

This is the timeout parameter for the feature code digit press attempts (in milliseconds). Default value is 3000.

Transfer Digit Timeout

This is the timeout parameter for inter-digit timing on feature code based transfers. Default value is 5.

Extension FAX Detect Timer

This is how long, in seconds, the PBX will detect to see if a call ringing to an extension is a fax. The setting is enabled under extension settings. Default value is 4.5. While auto-provisioning is Running, users may use the phone-based auto-provisioning mechanism in IPitomy phones to assign or create extensions. Click on to start, and Off to stop the service. This does not require saving or applying changes.

Auto-Provisioning

Table 57 – General PBX Admin Settings and Descriptions

Edit General PBX Settings

STEPS: 1

From the PBX Setup General System Setup page, locate the General Settings section.

2

Enter the information required for the PBX Security settings

3

Click the

2011 Copyright  IPitomy Communication, LLC

button to save the changes.

153 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide 4

Click the Apply Changes link located at the top right hand corner of the page, to commit the changes to the database.

2011 Copyright  IPitomy Communication, LLC

154 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Security Settings Section Log Watch/Ban Service This feature allows the PBX to monitor the SIP registration traffic and ban any IP address that makes 5 failed registration attempts. The IP address will be banned for either 5 days or until the service is restarted. Configuration settings allow you to ignore (not monitor) IP addresses that are communicating from the LocalNet, as well as allowing you to manually add addresses you want the system to ignore.

Figure 83 – PBX Security Log Watch and Ban Service Status

Enable Log Watch/Ban Service

STEPS: 1

From the PBX Setup General System Setup page, locate the Security Settings section.

2

Enable the Log Watch Ban Service by setting the parameter to “Yes” on the dropdown list.

3

Click the

4

Scroll back to the Log Watch Ban Service panel and click the Reload button.

button to save the changes.

Set Log Watch/Ban Service Parameters Once you have enabled the Log Watch/Ban Services, you will be able to configure the parameters for the security settings.

Figure 84 – Security Log Watch and Ban Security Settings

2011 Copyright  IPitomy Communication, LLC

155 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide The following table describes the parameters and descriptions (recommended settings) for the Log Watch and Ban feature. Sections/Fields Service is currently Running

Description This indicates the status of the service, either Running or Not Running. Restarts the Ban service, clearing any existing banned IP addresses.

Reload Button

Set to Yes and the PBX will monitor failed SIP registration attempts. 5 failed attempts and the IP is blocked for: Enable Log Watch & Ban Service



5days



Until system reboot



Until Reload button is clicked

Ignore IPs in SIP LocalNets

Set to Yes and the PBX will ignore failed SIP registration attempts from IPs from the LocalNets configured in the system. When set to No, IP addresses from the LocalNets are ignored for failed attempts.

Ignoring Addresses

Lists the addresses that were manually entered to be ignored in regards to failed SIP registration attempts

Add Entry

Enter the IP addresses you wish to be ignored by the PBX in regards to failed SIP registration attempts. Table 58 – PBX Security Log Watch/Ban Settings and Descriptions

Configure Log Watch/Ban Service

STEPS: 1

Navigate to PBX SetupGeneral.

2

Scroll down to the Security Settings panel, set the parameters based on your general business requirements.

3

Click the

4

Navigate to the PBX SetupGeneral page. Locate the Admin Settings section (located at the top of the page).

5

Enter an IP address for Admin Email Address field. Depending on whether you have Unified Messaging configured, the PBX will send an email to this address any time that it bans an IP address. See the Unified Messaging section of this guide for details on how to configure this parameter.

6

Click the Apply Changes link located at the top right hand corner of the page, to commit the changes to the database.

2011 Copyright  IPitomy Communication, LLC

button to save the changes.

156 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide IMPORTANT: Please contact IPitomy’s Technical Support Group if you need further assistance by email at [email protected] or phone 941-306-2200 option 2. You can also search the FAQ page on our website at www.ipitomy.com.

!

Disable Log Set Security Setting

STEPS: 1

From the PBX Setup General System Setup page, locate the Security Settings panel.

2

Disable the security setting by selecting “No” from the drop-down list for the Log Watch Ban Service.

3

Click the

4

Click the Apply Changes link located at the top right hand corner of the page, to commit the changes to the database.

button to save the changes.

Time Settings Section

Figure 85 – PBX Time Settings Section

Sections/Fields Current System Time Synchronize Timezone

Description This is the current time of the PBX system. Clicking this button will cause the PBX to sync to the time server. This will result in a restart of services, interrupting calls. If the time is off by more than an hour, we advise you to reboot the PBX after synchronization. This is the time zone for the PBX system.

2011 Copyright  IPitomy Communication, LLC

157 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide Network Time Server Time Server Info

This is the location of the PBX time server. If nothing is entered in the field, the PBX is using the default value of time.nist.gov. Below the Network Time Server field is a display showing information about the system’s connection to its time server. Table 59 – PBX Time Settings and Descriptions

Set Time Settings

STEPS: 1

From the PBX Setup General System Setup page, locate the Time Settings panel.

2

Set the Timezone to match your location.

3

If needed, set the Network Time Server to the desired address. Typically the default value will work.

4

Click the

5

Click the Apply Changes link located at the top right hand corner of the page, to commit the changes to the database.

2011 Copyright  IPitomy Communication, LLC

button to save the changes.

158 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Outbound Transfers Numbers Section This setting allows outside numbers, such as cell phones or land lines, which receive calls through the PBX to press ## to transfer the call. Once connected, the call can be transferred to someone else at the office or another number, depending on configuration. Simply ask them to hold, then press ##. After a moment the PBX will say “Transfer”, after which you can dial the number where the call should be transferred to. Any numbers listed here will be able to perform this type of transfer. Use the Transfer Permissions setting to define where calls may be transferred to. Internal Only restricts the transfers to extensions only. If you set it to an extension, then you can transfer anywhere that extension could, following the Class of Service for outbound dialing.

Figure 86 – Outbound Transfer Numbers Section

Add Outbound Transfers

STEPS: 1

From the PBX Setup General System Setup page, locate the Outbound Transfer Numbers section.

2

To in the box to the left of the Add button, enter the phone number you wish to be able to use this transfer feature. Click Add to move the number to the list. Repeat this step for all the numbers you want to add.

3

Select the desired permission from the Transfer Permissions drop-down list.

4

Click the

5

Click the Apply Changes link located at the top right hand corner of the page, to commit the changes to the database.

button to save the changes.

Delete Outbound Transfers

STEPS: 1

From the PBX SetupGeneral System Setup page, locate the Outbound Transfer Numbers section.

2011 Copyright  IPitomy Communication, LLC

159 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide 2

From the list of transferable numbers, click on the number(s) that you want to delete. You can use the SHIFT or CTRL button to select multiple numbers on the list.

3

Click the DEL button. The selected numbers are removed from the list .

4

Click the

5

Click the Apply Changes link located at the top right hand corner of the page, to commit the changes to the database.

button to save the changes.

InGenius Connector rd

InGenius is a 3 party software licensable on the IPitomy PBX. The settings under PBX SetupGeneral are where you would configure the user name and password InGenius. Contact IPitomy for more information.

Figure 87 – InGenius Connector Settings Section

2011 Copyright  IPitomy Communication, LLC

160 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Database Administration Create Backup Section

Figure 88 – Create Backup Section

Sections/Fields

Description Use this field to enter keywords to identify what the backup you are making pertains to.

Description

This is the types of files that you want to create backups for. Select the desired type by clicking in the box to the left of the item. This will place a checkmark next to the item. Available categories are: • Prompts • Music On Hold • Database • License • Voicemail • Logs Clicking the Create button will generate a backup file on the PBX containing the information selected under Categories.

Categories

Create

Table 60 – Create Backup Settings and Descriptions

Creating a Backup

STEPS: 1

From the PBX SetupDatabase Administration page, locate the Create Backup section.

2

From the Create Backup section, enter the keywords in the Description field for the backup file you want to create.

3

Select the categories you want included in the backup.

4

Click on the CREATE button to create the backup file.

5

Scroll down to the Date/Time section of the Database page. The backup file that was just created will appear at the bottom of the list with the corresponding date and time the

2011 Copyright  IPitomy Communication, LLC

161 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide backup was made. Use your mouse to hover over the date and time field and the keywords entered will be displayed.

Automatic Backups Section With this feature, you can have the PBX automatically create backups at a set interval, as well as send those backups to an external FTP. The system will only store a total of 4 automated backups at any given time, overwriting the oldest when a new on is created.

Figure 89 – PBX Database Automatic Backups Section

Sections/Fields Enabled

Description If Enabled (set to YES), a backup will be performed automatically based on the interval set under Schedule. This is the types of files that you want to create backups for. Select the desired type by clicking in the box to the left of the item. This will place a checkmark next to the item. Available categories are:

Backup Categories

Schedule FTP Backups Enabled FTP Server

• Prompts • Music On Hold • Database • License • Voicemail • Logs This is the frequency for which you want the automated backup to be performed. Options are Daily, Weekly and Monthly. If Enabled (set to YES), the PBX will send automatic backups to the configured FTP server This is the FTP server address that the FTP backup will be stored.

2011 Copyright  IPitomy Communication, LLC

162 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide FTP Directory

This is the FTP directory on the server where a backup will be stored. Enter the Username required to write files to your FTP

User

Enter the password associated with the Username used to access your FTP

Password

This button will save the changes made to the automated backup settings.

SAVE Button

This button will initiate a test to validate the FTP server, directory, username, and password. A message will display the success or failure, and if successful, a test file will be placed on the FTP

Test Settings Button

Table 61 – PBX Database Automatic Backup Settings and Descriptions

Set Automatic Backup

STEPS: 1

From the PBX SetupDatabase Administration page, locate the Automatic Backup section.

2

Enabled the Automated Backup process by setting the Enabled field to “YES”.

3

Select the Category that you want to have backed up.

4

Set the Schedule to the desired interval.

5

Enter FTP parameters and Username and Password if you want the backup to be sent to an external FTP.

6

Click the Save button to save the settings.

7

Click on the Apply Changes link at the top of the page to save the information and commit the changes to the database.

8

Click the Test Settings button to validate the automated backup settings. You should receive a backup “Successful” message. If the setup test failed, you receive an “Error” with a message indicating what parameters failed.

9

Make the necessary adjustments to the backup parameter, Save, Apply Changes, and try the test again.

Upload Backup File Section This feature allows you to upload backup files to the PBX system.

Figure 90 – PBX Database Upload Backup File Section

2011 Copyright  IPitomy Communication, LLC

163 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Upload Backup Files

STEPS: 1

From the PBX SetupDatabase Administration page, locate the Upload Backup File section.

2

Click on the Browse button to search for the file you want to upload.

3

Double click on the file that you want to upload. The file directory will appear in the box next to the Browse button.

4

Click on the Upload File button to initiate the upload process. You should receive a message stating that the upload was “Successful”. If the upload process failed you will receive an “Error” message indicating what failed during the process.

Backup Storage Section The bottom of the Database Backup page lists the backup files that are stored on the PBX. The list will provide the following information for each backup file created:

Sections/Fields

Date/Time

Version Size

Description The Date and time the backup was created. If you mouse over the date/time for a particular entry, a tooltip with further information like categories and description will display. An asterisk denotes the backup was created by the automated backup feature. Version of the database when the back up was created. The size of the backup file. Delete Backup

Action

Restore Backup Download Backup Table 62 - Saved Backups

2011 Copyright  IPitomy Communication, LLC

164 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Figure 91 – Backup Date/Time Information

Delete Backup File

STEPS: 1

From the PBX SetupDatabase Administration page, scroll to the bottom of the page to find the backup files stored on the PBX.

2

Find the backup file that you want to delete.

3

Select the

4

Click on the Apply Changes link at the top of the page to save the information and commit the changes to the database. This will permanently remove the backup file from the server.

icon to the right of the backup file name. The file is removed from the list.

Restore Backup File

STEPS: 1

From the PBX SetupDatabase page, scroll to the bottom of the page to find the backup files stored on the PBX.

2

Find the backup file that you want to restore.

3

Select the

4

A box will appear prompting you on which values you wish to restore. Select per your needs, and click Restore.

5

Click on the Apply Changes link at the top of the page to save the information and commit the changes to the database.

icon to the right of the backup file name you want to restore.

2011 Copyright  IPitomy Communication, LLC

165 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide Download Backup File

STEPS: 1

From the PBX SetupDatabase Administration page, scroll to the bottom of the page to find the backup files stored on the PBX.

2

Find the backup file you want to download.

3

Select the icon to the right of the backup file name. The system will ask you whether want to open or save the file. Choose Save.

4

Depending on your browser settings, you may have to define where the file should be downloaded to.

Voicemail Setup This page is used to configure global voicemail box settings, interact with the voicemail archive, as well as configuring the PBX to send out email notifications.

General Settings Section Used to configure global mailbox settings that are not found elsewhere in the PBX.

Figure 92 – PBX Voicemail General Settings Section

2011 Copyright  IPitomy Communication, LLC

166 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Sections/Fields

Description Maximum number of messages allowed for a voicemail box. Default value is 100.

Max Number of Messages

Maximum length of a message in seconds. Default value is 180.

Max Message Length

Minimum length of a message in seconds. Default value is 3.

Min Message Length

Maximum length of a greeting in seconds. Default value is 60.

Max Greeting Length Max Seconds of Silence

Maximum seconds of silence before the message is considered complete. Set this to zero for an infinite time period. Default value is 10. When using the maximum Seconds of Silence setting, it is sometimes necessary to adjust the silence detection threshold to eliminate false triggering on background noise. The higher the number, the more background noise is needed to break the silence. Default value is 128.

Silence Threshold

Table 63 – PBX General Settings and Descriptions

Set General Voicemail Settings

STEPS: 1

From the PBX SetupVoicemail Setup page. Scroll to find the General Settings section.

2

Set the General Voicemail parameters base on your business. In most scenarios, the default settings are fine.

3

Click the Save button to save the settings.

4

Click on the Apply Changes link at the top of the page to save the information and commit the changes to the database.

Voicemail Menu Section Configure settings that an individual voicemail box can follow globally.

Figure 93 – PBX Voicemail Menu Section

2011 Copyright  IPitomy Communication, LLC

167 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Sections/Fields

Description Play the envelope message (date/time) before playing the voicemail message. Default value is Yes.

Play Envelope Message Say Caller ID

Play the Caller ID information prior to the message, if available. Default value is Yes.

Skip ms on playback

This setting defines an interval in milliseconds to use when skipping forward or reverse while a voicemail message is being played. Default value is 3000. The number of retries a user has to enter voicemail passwords before the PBX will disconnect the user. Default value is 3.

Max Failed Login Attempts On Delete, play next msg.

Defines if the PBX will automatically play the next message after deleting a voicemail message. Default value is Yes.

Allow Review Mode

Global setting that defines if callers are able to listen to a message they left, and then decide if they want to re-record it or leave it as it is. Default value is No.

Allow Operator

Global setting in regards to if a voicemail box allows callers to press “0” to reach the System Operator Table 64 – PBX Voicemail Menu Setting and Descriptions

Set Voicemail Menu Options

STEPS: 1

From the PBX SetupVoicemail Setup page, locate the Voicemail Menu section.

2

Set the Voicemail E-mail parameters base on your business requirements. Typically the default setting will work.

3

Click the

4

Click on the Apply Changes link at the top of the page to save the information and commit the changes to the database.

2011 Copyright  IPitomy Communication, LLC

button to save the settings.

168 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

E-mail Settings Section This section is used to define the email address and server the PBX will use to send out Unified Messaging and notification emails. Unified Messaging allows a user to receive emails whenever they receive new voicemail messages. If the PC where you check your email has the capacity to play .wav files, the you will be notified when an email is received, and will be able to listen to the new message directly from the email. Notification emails are sent out for features like Log Watch/Ban.

Figure 94 – PBX Voicemail Settings Section

Sections/Fields Voicemail as Attachment

Description Defines if new voicemail messages will be attached and set in an email.

From Address

The email address to be used in the From address of the voicemail message. . Note: Most providers require that this is set to the address of the account used for sending the messages.

Voicemail Server

Allows voicemail services to be provided by an external server. It is not recommend to use the “Loc(local)” setting. This setting will be removed in a future release.

Server Address

This is the mail server address. Enter either a fully qualified host name or an IP address.

SSL Support Server Port

Enable if the email server uses SSL encryption. If the email server uses a port other than 25, define that port here.

2011 Copyright  IPitomy Communication, LLC

169 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide Authentication Required

Defines if the email server requires a username and password to gain access and send messages. The user name associated with the use of the external email server.

User Name

The external email server password.

Password

Table 65 – PBX Voicemail Settings and Descriptions

Set E-mail Settings

STEPS: 1

From the PBX SetupVoicemail Setup page, scroll to find the Email Settings section.

2

Set the Voicemail E-mail parameters base on your business requirements or what is recommended by IPitomy.

3

Click the Save button to save the settings.

4

Click on the Apply Changes link at the top of the page to save the information and commit the changes to the database.

Test Settings Button

STEPS: 1

From the PBX SetupVoicemail Setup page, locate the E-mail Settings section.

2

Located at the button of the E-mail Settings section is the Test Settings button. Click on this button to generate a test of the email settings entered.

3

The “Email to send a Test message to:” window appears. Enter the email address that you want the test message sent to then click the OK button.

4

If the email setting and address is valid, you will receive a “SENDEMAIL Successful!” message at the button of the Test Settings button. The email recipient that was entered will also receive an email with a subject titled “Voicemail Server Test”.

5

If the email setting test failed, you will receive an “Error!” message at the button of the Test Settings button. Check the message for hints as to what caused the failure (ie. SSL enabled but not needed).

2011 Copyright  IPitomy Communication, LLC

170 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide 6

Reconfigured the email parameters per the Set Email Settings steps above, then test again.

Refer to the Extension Settings Section for information on configuring email addresses for Unified Messaging. Refer to the PBX AdminGeneral Section for information on configuring email addresses for Log Watch/Ban.

Voicemail Archive Section Use this section to view which mailboxes currently have voicemail messages, and to download, upload, or erase the voicemail messages archived on the PBX.

Figure 95 – PBX Voicemail Archive Section

Sections/Fields

Description Displays the amount of space being used on the PBX for voicemail messages (Envelopes), greetings (Recordings), and the total.

Size List Mailboxes Using Space

Clicking on this box will display the list of mailboxes and the number of voice messages stored for each.

Download Button

This allows you to download a backup of all user voicemail messages, message envelopes and greeting files to your computer.

Erase Button

Deletes all user voicemail data on the PBX, including personal greetings. Used to upload a previously downloaded voicemail archive.

Upload Button

!

IMPORTANT: Uploading a voicemail archive will overwrite existing voicemail files on the PBX.

Table 66 – PBX Voicemail Archive Settings and Descriptions

Download Voicemail Archive Settings

STEPS: 1

From the PBX SetupVoicemail Setup page, locate the Voicemail Archive section.

2

Click on the Download button. Select Save File if prompted by your browser.

3

Define the location you wish to save the file if prompted by your browser.

2011 Copyright  IPitomy Communication, LLC

171 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide Erase Voicemail Archive Settings

STEPS: 1

From the PBX SetupVoicemail Setup page, locate the Voicemail Archive section.

2

Click on the Erase button. The warning message “This will delete all Voicemail recordings and user greeting. If you are sure you want to do this, click OK.”

3

Click the OK button to continue. The system performs the erase and returns you to the Voicemail Setup page.

Upload Voicemail Archive Settings

STEPS: 1

From the PBX SetupVoicemail Setup page, locate the Voicemail Archive section.

2

Click on the Browse button to search for the file location of the file you want to upload.

3

Click on the file that you want to upload. The file directory will appear in the box next to the Browse button.

4

Click on the Upload button to initiate the upload process. You should receive a message stating that the upload was “Successful”. If the upload process failed you will receive an “Error” message indicating what failed during the process.

5

Click the

6

Click on the Apply Changes link at the top of the page to save the information and commit the changes to the database.

button.

View Voicemail Listing (Usage Space)

Figure 96 – PBX Voicemail Listing Page

2011 Copyright  IPitomy Communication, LLC

172 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

STEPS: 1

From the PBX SetupVoicemail Setup page, locate the Voicemail Archive section.

2

Click the List Mailboxes Using Space link. A listing of the Mailboxes (extensions) and number of messages for each mailbox appears.

3

Click on the Hide Mailboxes Using Space link to close the listing.

SIP Setup SIP Networking Settings Section

Figure 97 – SIP Networking Settings Page

Sections/Fields

Description

Local Network & Subnet Masks Delete Selected Add Local Network External IP Add Button

This is the IP address to the local network and associated subnet masks. Allows you to delete the item selected from list of networks. Allows you to add local network information. This information will appear in the list of networks. The public IP address associated with the SIP network. This button will create/add the network information to the list of local network section.

Table 67 – SIP Networking Settings and Descriptions 2011 Copyright  IPitomy Communication, LLC

173 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide Add SIP Networking Settings

STEPS: 1

From the PBX SetupSIP page, locate the SIP Networking Settings section.

2

Enter the IP Address and Subnet Mask for the network the PBX is being installed on.

3

Click the Add button.

4

Click the

5

Click on the Apply Changes link at the top of the page to save the information and commit the changes to the database.

button.

Delete SIP Networking Settings

STEPS: 1

From the PBX SetupSIP page, locate the SIP Networking Settings section.

2

Highlight the listing you wish to delete. You can use Shift/Ctrl click functionality to select multiple listings.

3

Click the Delete Selected button.

4

Click the

5

Click on the Apply Changes link at the top of the page to save the information and commit the changes to the database

2011 Copyright  IPitomy Communication, LLC

button.

174 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

SIP Advanced Settings Section Advanced SIP settings define in more detail the management of network traffic. These settings are automatically provisioned when the system registers with the router. In most business implementations it is not necessary to make changes to these defaulted settings

2011 Copyright  IPitomy Communication, LLC

175 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

2011 Copyright  IPitomy Communication, LLC

176 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

2011 Copyright  IPitomy Communication, LLC

177 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Figure 98 – SIP Advanced Settings Page

!

IMPORTANT: The default settings for the SIP configuration should not require any changes. If it is necessary for you to do so to meet your customer’s business requirements, we recommend that you contact IPitomy’s Technical Support for assistance.

Sections/Fields Call Context Allow Guest Calls Host/Domain Name UDP Port Bind Address Enable DNS SRV Lookup Domains

2011 Copyright  IPitomy Communication, LLC

Description/Default Parameters Default: INCOMING Default: YES Default: BLANK Default: 5060 Default: 0.0.0.0 Default: NO Default: BLANK

178 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide Allow External Invites Auto Domain Enable Pedantic Checking

Default: YES Default: N/A Default: N/A

SIP TOS

Default is CS3. To configure QOS on your LAN, set your managed switches to prioritize packets flagged with CS3

RTP TOS

Default is CS3. To configure QOS on your LAN, set your managed switches to prioritize packets flagged with CS3

Video TOS

Default is CS3. To configure QOS on your LAN, set your managed switches to prioritize packets flagged with CS3

Max Length of Registration

Default: 7200

Default Length of Registration

Default: 3600

Notify Mime Type Time Between Mailbox Checks Voicemail Extension SIP Video Support

Default: BLANK Default: BLANK Default: BLANK Default: YES

Record History of Default

Default: N/A

First disallow all Codecs

Default: ALL

Allow Codecs Default Music on Hold Relax DTMF Handling

RTP Timeout

RTP Timeout on Hold Trust Remote Party ID

2011 Copyright  IPitomy Communication, LLC

Default: G.711 ulaw, G.711 alaw, GSM This will display whatever playlist is set to default on the PBX Setup=>Music On Hold page Default: YES Default is BLANK. Set to a value, in seconds, if you wish the PBX to end a call when no RTP traffic is detected for that long. Typically used in regards to lines that are not disconnecting correctly. Default: BLANK Default: N/A

179 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide Send Remote Party ID Progress in Band User Agent Allow Redirect to Nonlocal SIP Address User = Phone DTMF Mode Compact SIP Headers SIP Debug Subscriber Context Notify Ringing Qualify Generate Manager Events

Default: N/A Default: BLANK Default: BLANK Default: N/A Default: N/A Default: AUTO Default: N/A Default: N/A Default: BLANK Default: YES Default: 8000 Default: YES

External Host

Default is BLANK. When the site is using a dynamic public IP, you can go to dyndns.com, set up a domain with them, and enter that domain name here.

External Host Refresh

Default is BLANK. Set this under the interval used at dyndns.com for checking the current IP.

NAT Insecure Can Reinvite Cache Realtime Friends Real Time Update Auto-Expire Friends Ignore Registration Expiration Allow External Domains

2011 Copyright  IPitomy Communication, LLC

Default: YES Default: VERY Default: N/A Default: YES Default: N/A Default: N/A Default: N/A Default: YES

180 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide Table 68 – SIP Advanced Settings and Descriptions

Edit Advanced SIP Networking Settings

STEPS: 1

From the PBX SetupSIP page, click on the Advanced link.

2

The Advanced SIP Networking Settings page is displayed.

3

Set the SIP Network parameters base on your business requirements or what is recommended by IPitomy.

The default settings should not require any changes. If it is necessary for you to do so to meet your customer’s business requirements, we recommend that you contact IPitomy’s Technical Support for assistance.. 4

Click the

5

Click on the Apply Changes link at the top of the page to save the information and commit the changes to the database.

button.

Prompts Prompts are voice recordings used by a Menu to define the options that can be selected in the menu, or to simply convey information.

Upload Voice Prompt Section This feature allows you to upload a voice prompt file and store it in the PBX server for use. Once loaded, you can select which menus you wish to use the Prompt file.

Figure 99 – Upload Voice Prompt Section

Upload Voice Prompt

STEPS: 1

From the PBX SetupEdit Prompts page, locate the Upload Voice Prompt section.

2

Click on the Browse button in the Upload Voice Prompt section of the page.

3

Specify the location of the voice prompt file you want to upload (the accept file format is .gsm, the file name should not contain any spaces or special characters)

4

Click the Upload File button.

5

Once the file is uploaded it will be listed in the Prompt Files on Server section.

6

Click on the Apply Changes link at the top of the page to save the information and commit the changes to the database.

2011 Copyright  IPitomy Communication, LLC

181 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide Record New Voice Prompt Section This feature allows you to record a new voice prompt and store on the PBX server. Once created you can define which menus you wish to use the Prompt file.

Figure 100 – Record New Voice Prompt Section

Record New Voice Prompt

STEPS: 1

From the PBX SetupEdit Prompts page, locate the Record New Voice Prompt section.

2

Enter a description in the Prompt Name and the Extension number of the person who will be recording the prompt.

3

Click on the Record button. The system will display a message stating that it is trying to call the extension. When the connection is successful, the phone at that extension will ring.

4

Answer the call and record the message. Be sure to follow the in-call directions through till the system says ‘Goodbye”.

5

When you have completed the recording, press the Continue button. The system will return you to the Edit Prompts page.

6

Click on the Apply Changes link at the top of the page to save the information and commit the changes to the database.

2011 Copyright  IPitomy Communication, LLC

182 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Prompt Files on Server Section All record prompt files are stored on the PBX server and will appear in the Prompt Files on Server listing of the Edit Prompts page.

Figure 101 – Prompt Files on the Server Section

Delete Prompt Files on Server

STEPS: 1

From the PBX SetupEdit Prompts page, locate the Prompt Files on Server list.

2

Select the icon to the right of the prompt file, listed under the File Name column, that you want to delete. The file is removed from the list.

3

Click on the Apply Changes link at the top of the page to save the information and commit the changes to the database.

Download Prompt Files on Server

STEPS: 1

From the PBX SetupEdit Prompts page, locate the Prompt Files on Server list.

2

Select the icon to the right of the prompt file, listed under the File Name column, you want to download.

3

Specify the location where you want to download voice prompt file. Once the download is complete, the system will return you to the Edit Prompts page.

4

Click on the Apply Changes link at the top of the page to save the information and commit the changes to the database.

2011 Copyright  IPitomy Communication, LLC

183 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Music on Hold The PBX allows you to create multiple play lists that can be populated with music files. Once a playlist is configured, you can define for this to be the System Default Hold music, or specify to use this playlist under individual Extensions, Groups, or Menus.

Systems Default Music on Hold Section

Figure 102 – System Default Music on Hold Section

Set Default Music on Hold Section

STEPS: 1

From the PBX SetupMusic on Hold page, locate the Systems Default Music on Hold section.

2

Select the desired Music on Hold Playlist from the drop-down list.

3

Click on the Set Default button.

4

Click on the Apply Changes link at the top of the page to save the information and commit the changes to the database.

2011 Copyright  IPitomy Communication, LLC

184 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Create a Playlist Section

Figure 103 – Create a Playlist Section

Add New Music on Hold

STEPS: 1

From the PBX SetupMusic on Hold page, locate the Create a Playlist section.

2

Enter a single word description of the playlist in the Name field.

3

Set the Random preference to either YES or NO.

4

Click the

5

Click on the Apply Changes link at the top of the page to save the information and commit the changes to the database.

6

The new Playlist name is added to the playlist on the Music on Hold page.

2011 Copyright  IPitomy Communication, LLC

button to save the changes.

185 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Upload Music Files

Figure 104 – Music on Hold Playlist The following steps describe how to upload Music on Hold file to the PBX system.

STEPS: 1

From the PBX SetupMusic on Hold page, locate the Name of the Music on Hold playlist you wish to upload the music file to.

2

Click on the Name link from the list of Music on Hold files or the the name.

3

The Edit Music on Hold page appears. Click on the Browse button in the Upload Music on Hold section of the page.

4

Specify the location of the music file you want to upload (accept formats are .mp3, .wav or .gsm) to the PBX system then click the Upload File button.

5

Click the

6

Click on the Apply Changes link at the top of the page to save the information and commit the changes to the database.

icon to the right of

button to save the changes.

Delete Music Files on Server

STEPS: 1

From the PBX SetupMusic on Hold page, locate the Name of the Music on Hold file that you want to delete.

2

Select the icon to the right of the music file Name that you want to remove. The file name is removed from the list of music files.

3

Click the

2011 Copyright  IPitomy Communication, LLC

button to save the changes.

186 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide 4

Click on the Apply Changes link at the top of the page to save the information and commit the changes to the database.

Feature Codes This section lists a number of basic codes users can dial from their phone to access certain features on the PBX. Additionally, at the bottom of the page you can find a section that allows for configuration of System Speed Dials.

Speed Dialing Section

Figure 105 – Features Code Speed Dialing Section

Sections/Fields

Description Enter a 2 digit code between 00 and 98. This is the code the user will enter to access the speeddial.

Extension

Enter a recognizable value that relates to the number being dialed

Label PSTN number

This is the phone number that will be dialed when the code is dialed. Only enter digits that could be dialed from a phone (numbers, *, #). Table 69 – Features Code Settings and Descriptions

Add Speed Dialing

STEPS: 1

From the PBX SetupFeature Codes page, locate the Speed Dialing section.

2

Enter the Extension number, Label name and PSTN number for the speed dial in the Add/Edit Speed Dial section.

3

Click on the Save Entry button to save the information. The system will create the speed dialing code and it will appear in the listing.

2011 Copyright  IPitomy Communication, LLC

187 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide 4

Click on the Apply Changes link at the top of the page to save the information and commit the changes to the database.

Edit Speed Dialing

STEPS: 1

From the PBX SetupFeature Codes page, locate the Speed Dialing section.

2

Click on the icon to the right of the speed dial code you want to edit. The information for the speed dial code will appear in the Add/Edit Speed Dial section.

3

Edit the necessary information then click on the Save Entry button to save the information.

4

Click on the Apply Changes link at the top of the page to save the information and commit the changes to the database.

Delete Speed Dialing

STEPS: 1

From the PBX SetupFeature Codes page, locate the Speed Dialing section.

2

Select the icon to the right of the speed dial code you want to remove. To remove multiple speed codes at one time, click on the box to the left of the codes then click the Delete Selected button.

3

The file name is removed from the list of speed dial codes.

4

Click on the Apply Changes link at the top of the page to save the information and commit the changes to the database.

Import/Export Speed Dialing List (CSV)

STEPS: 1

From the PBX SetupFeature Codes page, locate the Import/Export List section.

2

Click on the Browse button in that section of the page.

3

Specify the location of the file you want to import from or export to and then click the appropriate function button (import or export).

4

The system will perform the function you selected and will tell you whether it was successful in the attempting to process the request.

5

Click on the Apply Changes link at the top of the page to save the information and commit the changes to the database.

2011 Copyright  IPitomy Communication, LLC

188 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Services System Information Section

Figure 106 – Services System Information Page Sections/Fields System Software Version

RAID Status

Licensed to

Licensed extensions

Service Tag

Description This is the software version that is running on the PBX system. Defines the status the system Raid (if it has one). RAID is Redundant Array of Independent Disks. RAID is available in Software and Hardware versions. 1100 and 1200 systems can only deploy SW RAID. 2000 and 5000 systems are typically deployed using Hardware RAID. Displays the name of the company the PBX is licensed to. Displays how many extensions the system is licensed for. If you try to create more extensions they the PBX has licenses, a warning will display to alert you. There are licenses for both IPitomy branded telephones and non-IPitomy branded telephones. Telephones are assigned the correct license automatically. Unique serial number for the PBX, used when licensing the system.

2011 Copyright  IPitomy Communication, LLC

189 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide Unique ID used for licensing the system.

Host ID

Unique key used for licensing the system.

System Key Download License Info Button

Clicking this button will save a text file on your PC. This file contains the Unique ID, Serial, and Key of the PBX. Be sure to email this file along with your purchase order when buying additional licenses,

Table 70 – Services System Settings and Descriptions

View System Information

STEPS: 1

From the PBX SetupServices page, locate the System Information section.

2

Use the table of settings and their description for an explanation of how the system is configured.

License Information Section This feature allows you view what licensed features are available on the system. You can upload or download licenses for the PBX applications. You can also assign Call Manager licenses to users. The following section describes how to perform these functions.

Figure 107 – Services Download License Information Section

2011 Copyright  IPitomy Communication, LLC

190 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Sections/Fields

Description Defines which additional features are licensed on the system. Available features are: ACD InGenius

Features

Multisite Call Scheduling

Desktop Call Manager Licenses

Displays how many of each Call Manager member type are licensed on the PBX. Currently Operator and User are the only functional license. Clicking the Assign User Licenses button will open a new window for assigning call manager licenses.

License File

In this panel you can download the current license file, or upload a new license. Table 71 - License Info Descriptions

Upload License File

STEPS: 1

From the PBX Setup Services page, locate the License Info section.

2

Click on the Browse button in that section of the page.

3

Specify the location of the file you want to upload, then click Upload File button.

4

The system will log you out of the PBX.

5

Log back into the PBX.

6

Click on the Apply Changes link at the top of the page to save the information and commit the changes to the database.

Download License File

STEPS: 1 From the PBX Setup Services page, locate the License Info section. 2 Click the Download File button. 3 Your browser may prompt you as to where you wish to save the file.

2011 Copyright  IPitomy Communication, LLC

191 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Figure 108 – Services Assign Licenses Page

Assign Single User License

STEPS: 1

From the PBX SetupServices page, locate the License Info section.

2

Click the Assign User Licenses button. The “Assign IPitomy User Licenses” window appears. Find the name of the extension that you want to assign the license to. Choose the desired license type from the drop-down list (User/Operator).

3

Click the Submit button to save the changes. Click the Close button to close the active window.

4

Click the

5

Click the Apply Changes link located at the top right hand corner of the page, to commit the changes to the database.

button to save the changes.

If this is the first time a license has been assigned, be sure to return to the servies page and click the Restart Call Manager button.

2011 Copyright  IPitomy Communication, LLC

192 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide Assign Multiple User Licenses

STEPS: 1

From the PBX SetupServices page, locate the Download License info section.

2

Click the Assign User Licenses button. The “Assign IPitomy User Licenses” window appears. Click on the box (place a checkmark) to the left of each of the extensions that you want to assign the licenses to.

3

Scroll down to the button of the page and select the license type (User/Operator) to assign to these extensions.

4

Click the Submit button to save the changes. Click the Close button to close the active window.

5

Click the

6

Click the Apply Changes link located at the top right hand corner of the page, to commit the changes to the database.

button to save the changes.

System Functions Section This section allows the administrator to restart some or all services in the PBX, as well as clear the Diagnostic log.

Figure 109 – Services System Functions Section

2011 Copyright  IPitomy Communication, LLC

193 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Sections/Fields

Description This will stop and restart all asterisk services on the PBX.

Restart PBX Daemon

!

IMPORTANT: Performing this function will drop all active calls.

This reboot the PBX. Reboot the PBX

!

IMPORTANT: Performing this function will drop all active calls.

This will restart all services, including asterisk, drivers, and web services of the PBX. Restart All Services !

Restart CallManager Daemon Clear Diagnostic Log

IMPORTANT: Performing this function will drop all active calls.

This will reinitialize Call Manager Sevices. It will drop any active instances of Call Manager. This will clear the Diagnostics logs from the PBX system.

Table 72 – Services System Functions and Descriptions

Restart PBX

STEPS: 1

From the PBX SetupServices page, locate the System Functions section.

2

Click on the Restart PBX button. All asterisk services on the PBX and return you to the Services page when it is done.

Reboot PBX

STEPS: 1

From the PBX SetupServices page, locate the System Functions section.

2

Click on the Reboot PBX button. The will perform a software reboot, and require you to log back in when it is done.

Restart Services

STEPS: 1

From the PBX SetupServices page, locate the System Functions section.

2

Click on the Restart Services button. The system will restart all the services that are running and return you to the Services page when it is done.

2011 Copyright  IPitomy Communication, LLC

194 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide Restart Call Manager

STEPS: 1

From the PBX SetupServices page, locate the System Functions section.

2

Click on the Restart Call Manager button. The system will restart process for the CallManager application and return you to the Services page when it is done.

Clear Diagnostics

STEPS: 1

From the PBX SetupServices page, locate the System Functions section.

2

Click on the Clear Diagnostics button. The system will clear all the diagnostic messages on the PBX server and return you to the Services page when it is done.

Load File System This area is used to load software files when performing an upgrade.

Figure 110 - Services Load File System Section

STEPS: 1

From the PBX SetupServices page, locate the File System section.

2

Click on the Browse button in that section of the page.

3

Specify the location of the file you want to load. The file must have the .tgz file extension.

4

The PBX will load the file, and the PBX will reboot.

5

Upon logging in, a prompt declaring the database version does not match will appear, Click OK and the database will be converted.

6

Click on the Apply Changes link at the top of the page.

2011 Copyright  IPitomy Communication, LLC

195 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide TFTP Files This panel allows the administrator to view, load, download, and delete files on the TFTP in the PBX. Typically, the files you would be loading will be phone firmware files.

Figure 111 – Services TFTP Files Section

Load TFTP File

STEPS: 1

From the PBX SetupServices page, locate the TFTP Files section.

2

Click on the Browse button in that section of the page.

3

Specify the location of the file you want to load onto the PBX.

Download TFTP File

STEPS: 1

From the PBX SetupServices page, locate the TFTP Files section.

2

Click on the blue TFTP Files link. A listing of the files that have been loaded on the TFTP server will be displayed.

3

Click on the blue link for the file you want to download. Your browser may require you to specify the location where you want to download the TFTP file.

Delete TFTP File

STEPS: 1

From the PBX SetupServices page, locate the TFTP Files section.

2

Click on the blue TFTP Files link. A listing of the files that have been loaded on the TFTP server will be displayed.

3

Find the name of the file you want to delete from the list.

4

Click on the Delete button. The file is removed from the list and the system will return you to the Services page.

2011 Copyright  IPitomy Communication, LLC

196 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Log File Settings This feature allows you indicate whether you want the logs to be written to a file or displayed on the PBX webpage.

Figure 112 – Services Log File Settings Section

Sections/Fields

Description

Log to File

If selected – the system will write the log messages to the ipitomy.log file, accessible by IPitomy Support. Default is enabled.

Display on Page

If selected – the system will display the log messages on the System Diagnostics page, accessable by anyone with Administrator access to the PBX. Default is enabled. Table 73 – Services Log File Settings and Descriptions

Select Log File Settings

STEPS: 1

From the PBX SetupServices page, locate the Log File Settings section.

2

Select (placing a checkmark in the box) the method that you want the log files to be handled. You can elect to do both, if so desired.

3

Click the

4

Click on the Apply Changes link at the top of the page to save the information and commit the changes to the database.

2011 Copyright  IPitomy Communication, LLC

button to save the changes.

197 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Logging Level Section This section of the Services page allows you to specify the type of messages that will be captured and available on the System Diagnostics page.

Figure 113 – Services Logging Level Section

Sections/Fields

Description If selected – the system will log Information level messages.

Information

If selected – the system will log Warning level messages.

Warnings

If selected – the system will log Error level messages.

Errors

If selected – the system will log all the message types above and some other types such as Notice.

All

Table 74 – Services Logging Levels and Descriptions

Select Logging Level

STEPS: 1

From the PBX SetupServices page, locate the Logging Level section.

2

Select (placing a checkmark in the box) the method that you want the log files to be handled. You can elect to select all the types, if so desired.

3

Click the

4

Click on the Apply Changes link at the top of the page to save the information and commit the changes to the database.

2011 Copyright  IPitomy Communication, LLC

button to save the changes.

198 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Call Event Log Section This allows you to enable web service and indicate the call event logs retention time.

Figure 114 – Services Call Event Log Section

Sections/Fields

Description

Enable Web Service

If Enabled (set to YES), the system will allow call events to be polled via the web service.

Password

This is the password that will be used to access the call event log files.

Log Retention

This indicates the number of months that the log files will be retained on the server. Default is 6 months. Table 75 – Services Call Event Logging and Descriptions

Set Call Event Logging

STEPS: 1

From the PBX SetupServices page, locate the Call Event Log section.

2

From the Enable Web Service field, select YES to enable the system to start polling the event logs. Otherwise, select NO if you do not want the system to perform this function.

3

In the Password field, enter the password that will be used to access the polling service.

4

Enter the number of months you want to retain the call event logs in the Log Retention field.

5

Click the

6

Click on the Apply Changes link at the top of the page to save the information and commit the changes to the database.

2011 Copyright  IPitomy Communication, LLC

button to save the changes.

199 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Automated Phone Firmware Updates This allows you to set the parameters for the system to perform automated firmware updates. Currently, when enabled, the PBX will check at midnight to see if there are more current phone firmware files available, and will download them if they exist.

Figure 115 – Services Automated Phone Firmware Updates The following table provides the parameters and their descriptions for the Automated Phone Firmware Updates feature. Sections/Fields

Description

Enable Firmware Update Service

If enabled (set to YES), then the system will perform an automated check for firmware updates.

Interval

This allows you to indicate how often the system will check for new firmware. Available internals are Daily, Weekly or Monthly.

Check for Firmware Now

This allows you to check for firmware on demand.

Table 76 – Services Automated Firmware Parameters and Descriptions

Set Automated Firmware Update Parameters

STEPS: 1

From the PBX SetupServices page, locate the Automated Phone Firmware Updates section.

2

Set the parameters defining if the system should automatically check for firmware, and the interval is should check.

3

Click the

4

Click on the Apply Changes link at the top of the page to save the information and commit the changes to the database.

button to save the changes.

Check for New Firmware Now

STEPS: 1

From the PBX SetupServices page, locate the Automated Phone Firmware Updates section.

2

Click on the Check Now button. The system will display the results once the process is complete. The following is a

2011 Copyright  IPitomy Communication, LLC

200 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide sample of what the message that will be displayed. This message demonstrates that the firmware version in the PBX and at IPitomy match.

Scheduled Calling This is a licensed feature that allows for periodic automated calls to be made by the PBX. This can be used for announcements, bells, alarms etc.

Figure 116 - Scheduled Calling

Enabling Scheduled Calling

STEPS:From the PBX SetupServices page, locate the Scheduled Calling section. 2

Change the dropdown to Enabled.

3

Click the

4

Click on the Apply Changes link at the top of the page to save the information and commit the changes to the database

button to save the changes.

Figure 117 - List of Scheduled Calls

2011 Copyright  IPitomy Communication, LLC

201 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Sections/Fields Select

Description Use this column to select which multiple entries to delete or edit. Displays if the entry is active.

Enabled

1: Enabled 0: Disabled

Name Start End Interval Execute Target Destination

Displays the name of the Scheduled Call. Displays the date which a particular entry is set to start. Display the date which a particular entry is set to end Displays information on when the Scheduled Call will take place. Shows the time the Scheduled Call will happen. Displays the Number to Call as defined in the Scheduled Call. Displays the Number to Connect as defined in the Scheduled Call. Click to edit individual entries. Click to test an individual entry. A call between the Target and Destination will be established. Click to delete individual entries.

Edit Delete Add

Click to edit multiple entries if checked in the Select column. Click to delete multiple entries if checked in the Select column. Click to create a new Scheduled Call. Table 77 - Scheduled Call List Descriptions

2011 Copyright  IPitomy Communication, LLC

202 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Figure 118 - Edit Scheduled Call

Sections/Fields Name

Description Enter a name to identify this Scheduled Call.

Date/Time

Define what date and time the Scheduled Call should start and end. You do not need to set an end time.

Recurrence

Defines the interval the Scheduled Call will take place. Calls can be set to Daily, Weekly, or Monthly. See the Recurrence table below for more details.

Execute At Number to Call Number to Connect Extension for COS Enable/Disable

Defines the time the call will take place for each Recurrence. Defines the entity that will be called. Defines what destination the called party will be connected to. Set this to the extension number that is using the Class of Service you wish this Scheduled Call to use when making outbound calls. Choose Enable for this Scheduled Call to be active, and Disable for it to be inactive. Table 78 - Edit Scheduled Call Descriptions

2011 Copyright  IPitomy Communication, LLC

203 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Figure 119 - Recurrence

Sections/Fields

Description Everyday: Will call at the defined Time every day.

Daily

Every X Days: Will call at the defined Time every (1-1550) days. Every Weekday: Will call at the defined Time every M-F.

Weekly

Every X Weeks on Y: Will call at the defined Time every (1-1550) weeks on the day defined. Day: Will call at the defined Time every (1st-31st) day of the month. st

Monthly

nd

rd

th

The X Week on Y: Will call at the defined Time on the 1 , 2 , 3 , or 4 week of the month on the day defined. Every X Months: Will call at the defined Time every (1-31) months. Table 79 - Recurrence Descriptions

Adding a New Scheduled Call

STEPS:From the PBX Setup Services page, locate the Scheduled Calling section. 2

If enabled, click the button for Manage Calls, which will take you to the List of Scheduled Calls page.

3

Click the Add button.

4

Configure your new Scheduled Call. If errors are made, you can click Reset to start over.

5

Click Submit to save.

6

Click the blue link Back to Services to return to the PBX Setup Services page.

7

Click the

8

Click on the Apply Changes link at the top of the page to save the information and commit the changes to the database

2011 Copyright  IPitomy Communication, LLC

button to save the changes.

204 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide Edit a Scheduled Call

STEPS:Navigate to the List of Scheduled Calls page. 2

Click the

icon to edit an individual entry, or place a check next to multiple entries and

click the Edit button. 3

Make the necessary changes.

4

Click Submit to save.

5

Click the blue link Back to Services to return to the PBX Setup Services page.

6

Click the

7

Click on the Apply Changes link at the top of the page to save the information and

button to save the changes.

commit the changes to the database

Edit a Scheduled Call

STEPS:Navigate to the List of Scheduled Calls page 2

Click the

icon to delete an individual entry, or place a check next to multiple entries

and click the Delete button. 3

Click the blue link Back to Services to return to the PBX Setup Services page.

4

Click the

5

Click on the Apply Changes link at the top of the page to save the information and

button to save the changes.

commit the changes to the database

Test a Scheduled Call

STEPS:Navigate to the List of Scheduled Calls page. 2

Click the

3

If the call does not work to your end users desires, reconfigure the Scheduled Call and test again.

button to test the call connection immediately.

REPORTING

Reports The Call Data Records (CDR) contain information about calls collected from the IPitomy IP PBX for a specified period of time. The report details the number of calls, call duration, call origination, call destination, and status. Call Data Records (CDR) can be sorted by specific time periods. CDR may also be exported in the same date 2011 Copyright  IPitomy Communication, LLC

205 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide range format. The records have also been enhanced for easier reading, and comprehension of data. To sort simply select the date range you wish to be displayed, and then press the view button. The display will be arranged and sorted according to your date selections.

Figure 120 – CDR Reports Page

2011 Copyright  IPitomy Communication, LLC

206 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Sections/Fields Date/Time

Description The date and time of the call. Defines where the call originated:

Direction

Internal: The call took place entirely within the PBX Outgoing: An internal entity made a call out a trunk. Incoming: An external party made a call inbound over a trunk.

Source

The originating party for the call.

Destination

The end location for the call.

Trunk

Defines which trunk was used for the call.

Duration

The length of the call in hours:minutes:seconds. The status describes the final state of a call through the PBX: Adandoned: Call entered a Queue, but the caller hung up before the call was answered or met the failover requirement. ChanUnavail: No channel was able to be created for the call due to a possible error state for the intended destination. Agent Completed: Connected Queue call was terminated at the extension. Hangup: Call to a Menu, but the caller hung up before taking any actions. Caller Completed: Connected Queue call was terminated at the calling parties end. Cancel: Call from an Extension, but the caller hangs up before the call is connected.

Status

Answer: A connected call. No Answer: A call that met the ring time of an extension without being answered. Timeout Exit: Call to a Queue that meets the Timeout. VM Not Left: Call ended with the caller being sent to voicemail where they did not leave a message. VM Left: Call ended with the caller being sent to voicemail where they left a message. Transferred: Connected call successfully transferred. Busy: Call out a trunk returned busy status, or extension was busy. - : Defines the call is still active, and the status will update when completed. Click on the call record for details. Exited Empty Queue: Call to Queue that follows Exit Empty rule. Exited With Key: Call to Queue that follows the Exit Menu key press. Table 80 - CDR Report Descriptions

2011 Copyright  IPitomy Communication, LLC

207 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

View CDR Report – Smart Personal Console IPitomy PBX Software version 3.4.1 and above have the added ability to view CDR Reports and Queue data from Smart Personal Console (SPC) using a special user name and password.

STEPS to access CDR and Queue Graphs via Smart Console Console: 1

Within PBX Administration, navigate to the PBX SetupGeneral page

2

Locate to the General Settings section (second section from the top).

3

Locate the SPC Reports User Password field (bottom of section)

4

It may be helpful to change this to a user-friendly password. If you change the password be sure to

and

.

5

Make a note of this password.

6

On the PC that will be used to access CDR Reports and Queue Graphs via SPC, open a web browser and navigate to the IPitomy PBX login screen

7

Using the right side – Smart Personal Console (User Login) input the word “reports” as the user name and the password that you noted previously.

8

Click on

9

The CDR-Report page is opened, use the instructions below to extract the data you wish. Or,

.

10 Click on that data.

2011 Copyright  IPitomy Communication, LLC

to open that interface and use the instructions below to extract

208 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

View CDR Report – PBX Administration

STEPS: 1

From the ReportingReports page, click on the CDR Report button. The CDR Report page appears.

2

Select the From and To date range by click on the box next to the From and To fields. Use the calendar control page that appears to select the desired dates.

3

Click the View button. A report with call information from the date range parameter that was entered is displayed.

4

Click on an individual call record and a new window will appear displaying more detailed information for that call.

Export CDR Report The Export function will provide you with a tabulated report to download to a PC.

STEPS: 1

From the ReportingReports page, click on the CDR Report button. The CDR Report page appears.

2

Enter the date range and retrieve the report that you want to export (see steps for Viewing Report).

3

Click the Export button then specify the location where you want to download the report.

Queue Graphs Queue Graphs display additional call information for ACD Queues. A PBX must be licensed for ACD for this button to appear.

Figure 121 – Queue Graphs Page 2011 Copyright  IPitomy Communication, LLC

209 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Sections/Fields

Description This is the listing of the queue you want to view. The drop-down list is populated with the various groups that have been configured.

Queue Type

This allows you to specify a range of dates for which call records will display.

Date

This allows you to specify a start and end time within the date range for the reporting to display.

Time

This is the increment with which to sort by. The default increment is 2 hour.

Setting Stretch Graph

Move the slider to adjust the size of the graph to meet your viewing requirements. Table 81 – Queue Graphs Search Parameters

Run Queue Graph Report

STEPS: 1

From the ReportingReports page, click on the Queue Graphs button. The Queue Graphs page appears.

2

Select the Queue Type from the drop-down list.

3

Select the Start and End date using the calendar control that appears when you click on the date fields. Select the desired Start and End time for the reporting period you want to search.

4

Change the Sorting parameters to the desired setting.

5

Click the Update button. The system will perform the search based on the criteria that is specified and display the results.

2011 Copyright  IPitomy Communication, LLC

210 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Overview Tab The Overview Tab offers an overall summary of the calls for the period in question for that queue. The overview will display textual information for answered and unanswered calls, as well as a graph summarizing the information.

Figure 122 – Reports Queue Graph Overview Tab Sections/Fields Total Calls Avg. Call Wait Length Min. Wait Length Max Wait Length Avg. Call Length Min. Call Length

Description Total number of calls answered, or unanswered. An average of the wait time for calls answered, or unanswered. Shortest wait time for calls answered, or unanswered. Longest wait time for calls answered, or unanswered. Average duration of an answered call. Shortest duration of an answered call.

2011 Copyright  IPitomy Communication, LLC

211 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide Max Call Length

Longest duration of an answered call.

Agents Tab

Figure 123 – Reports Queue Graphs Agents Tab The Agents tab displays details for queue members. Sections/Fields Queue

Description Time spent on queue calls. Number of calls displayed in parenthesis.

Inbound

Time spent on inbound, non-queue calls. Number of calls displayed in parenthesis.

Outbound

Time spent on outbound, non-queue calls. Number of calls displayed in parenthesis.

Internal

Time spent on internal, non-queue calls. Number of calls displayed in parenthesis.

Pause Time

Time spent paused out of the queue. Number of calls displayed in parenthesis.

2011 Copyright  IPitomy Communication, LLC

212 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Graph Tab The Graph Tab provides a graphical view of queue calls only. Inbound and outbound calls are tabulated but not graphed. The graph tab divided into time segments defined by the Sorting setting set previously. The information presented in this tab will allow you to determine busiest times and when call coverage is most needed.

Figure 124 – Reports Queue Graphs Tab

Logs Tab The Logs Tab will display the complete call log for the queue from your search setting. It will display the time of the call, the direction of the call either inbound or outbound, the caller ID that was delivered with the call, the location that the call was delivered to, the wait time for the caller, the total duration of the call, and finally the outcome of the call or the final status of the call. See the table for CDR Report Descriptions for detailed information about the fields.

Figure 125 – Reports Queue Graphs Logs Tab

2011 Copyright  IPitomy Communication, LLC

213 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Diagnostics This section, when configured under PBX SetupServices, displays a message log of actions in the PBX. Typically this page will be referenced by Tech Support to pinpoint where troubleshooting for a specific problem should begin.

Figure 126 – System Diagnostics Page

View System Diagnostics STEPS: 1

Click the ReportingDiagnostics link on the Admin Page.

2

The System Diagnostics page appears displaying the messages that have been processed and their status.

3

The type of message that is displayed on this page is set in the Logging Level section of the Systems page.

2011 Copyright  IPitomy Communication, LLC

214 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Monitoring This page gives a snapshot of the status of your SIP network. Extensions, SIP Providers, Branch Offices, and active calls will display. Entries in Green are connected, entries in Red are unable to be reached, and entires in Grey are not present. At the bottom of the page, active calls will display on a channel by channel basis. The page will refresh every 10 seconds.

Figure 127 – Monitoring Page

2011 Copyright  IPitomy Communication, LLC

215 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

APPENDICES Appendix 1: Key Types and Codes This table describes the function of each key type, and how to manually configure them. It is not advised to manually configure unless the phone is in a situation where you cannot easily use the PBX to set the keys (ie: remote phones). Unless specified, the Line field when manually configuring should be set to All. Key Type

Description Can be set to an extension or park orbit. Pressing the key will call the extension or retrieve a call from the park orbit. When an extension is ringing the light will flash, and when an extension is connected to a call, the light will be solid. Park BLF keys will lamp when a call is parked in that particular orbit. To manually configure, log into the phone and set the key to:

BLF

Type: BLF Label: Meaningful Descriptor Value: The extension or park orbit number to monitor Line: 1 Dials the digits entered as for the Value and sends them to the PBX. To manually configure, log into the phone and set the key to: Type: Speed dial

Speed Dial

Label: Meaningful Descriptor Value: Any number or feature code that the PBX can recognize Takes the connected call and parks it in an available orbit from 701-720, starting at the lowest available slot. When parking, the PBX will tell you audibly which orbit the call was sent to. To manually configure, log into the phone and set the key to:

Park

Type: Park Label: Park Value: ##700#

DND

Places the phone itself in a state where it will not receive calls. This does not communicate your state to the PBX (see Pause key). To configure manually, log into the phone and set the key to: Type: Do Not Disturb This key starts the transfer process and allows you to enter a transfer destination. Once entered, press Dial or wait for the digit timeout and the call will transfer. This key is most useful if a phone has no open lines to perform a transfer using the fixed key on the phone, as it does not open a new line to transfer. To configure manually, log into the phone and set the key to:

Blind Transfer

Type: Prefix Label: Blind Transfer Value: ##

2011 Copyright  IPitomy Communication, LLC

216 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide Allows the user to answer calls ringing direct to extensions that are in the Call Group that matches the phones Pickup Group. To manually configure, log into the phone and set the key to: Call Pickup

Type: Pickup Label: Meaningful Descriptor Value: 99 Allows the user to check their voicemail messages. User will be prompted for their password(PIN). To manually configure, log into the phone and set the key to: Type: Speed dial

Voicemail

Label: Voicemail Value: 923 Allows the user to check any voicemail box for messages. User will be prompted for mailbox number and password(PIN). To manually configure, log into the phone and set the key to:

Voicemail Gateway

Type: Speed dial Label: VM Gateway Value: 924 Toggles on and off the record feature on the current active call. The file will be saved in the voicemail box for the extension, under the Work folder. To manually configure, log into the phone and set the key to:

Record

Type: Speed dial Label: Record Value: *# With a single press, a user can enable their unconditional forwarding. If no destination is set, you will need to define one before forwarding can be enabled. To manually configure, log into the phone and set the key to:

Fwd On

Type: Speed dial Label: Fwd On Value: *91 With a single press, a user can disable their unconditional forwarding. To manually configure, log into the phone and set the key to: Type: Speed dial

Fwd Off

Label: Fwd Off Value: *90 With a singe press, a used can define their forwarding destination. To manually configure, log into the phone and set the key to: Type: Speed dial

Set Fwd

Label: Set Fwd Value: *92

2011 Copyright  IPitomy Communication, LLC

217 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide This takes the user to a gateway that allows them to control forwarding for extensions other than their own. User will be prompted for an extension number and password (PIN) before they can make changes. Once logged in, you can enable, disable, and set the forward destination. To manually configure, log into the phone and set the key to: Fwd Gateway

Type: Speed dial Label: Fwd Gateway Value: *9 This key starts the intercom process and allows you to enter an extension or group number. Once entered, press Dial or wait for the digit timeout, and the page will happen. To manually configure, log into the phone and set the key to:

Intercom

Type: Intercom Label: Intercom Similar to the DND key, except pressing this key communicates to the PBX, and will pause you out of call queues. The key is a BLF and will lamp when the phone is paused. To manually configure, log into the phone and set the key to: Type: BLF

Pause

Label: Pause Value: ABC Line: 1 When pressed, a call is established to the PBX telling the user the state of Day/Night mode override, and gives instructions on how to change the settings. If Day/Night mode is forced into night mode, the light will blink; and if forced into day mode, the light will be solid. If Day/Night mode is following the schedule the BLF will not lamp. To manually configure, log into the phone and set the key to:

Day/Night BLF

Type: BLF Label: Day/Night Value: ff Line: 1 Allows BLF monitoring of an extension, as well as one press paging to that extension. TO manually configure, log into the phone and set the key to: Type: BLF

Page BLF

Label: Meaningful Descriptor Value: ** Line: 1

2011 Copyright  IPitomy Communication, LLC

218 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Appendix 2: IP Telephones IPitomy 550 The IPitomy IP550 SIP based telephone is designed for busy business environments. The IP550 is the workhorse phone for any business with a wide range of telecommunications requirements. Equally, at home on the desk of a corporate executive or on a conference table, the IP550 fits just about any business situation. The IP550 is an advanced open standards business telephone. With features that are based on the technology of the future, the IP550 also includes most of the familiar functions available on traditional business telephone systems. The combination of high technology and practical functionality results in a standardsbased telephone that is simple to use and won’t require a long learning curve. The 20 soft keys, 6 programmable keys and 16 fixed feature keys, provide all of the flexibility required for any business. Because the IP550 is designed as a SIP based telephone, its robust capabilities perform well in or out of the office. Remote users can enjoy the same great features as though they were right in the office. The large graphical display conveniently displays caller ID information. Missed calls, dialed calls and received calls are stored and can be viewed, dialed or stored in the on board phone book. The full duplex speakerphone provides world class speaker phone quality. The attractive appearance and sturdy stand provide a professional look and feel. The IP550 enhances the performance of the IPitomy IP PBX systems and is far more integrated that other open standards SIP based endpoints.

IPitomy 55i The 55i from IPitomy offers powerful features and flexibility in a standards based carrier-grade advanced level expandable IP telephone. With a sleek and elegant design, 144 x 75 pixel backlit LCD display and 6 dynamic context-sensitive softkeys, the 55i is fully interoperable with leading IP Telephony platforms, offering advanced XML capability to access custom applications and support for up to 9 calls simultaneously. Part of the IPitomy family of IP telephones, the 55i is ideally suited for moderate to heavy telephone users who require more one touch feature keys and XML based programs.

IPitomy 53i The 53i from IPitomy offers powerful features and flexibility in a standards based carrier-grade basic level IP telephone. With a sleek and elegant design and 3 line LCD displays, the 53i is fully interoperable with leading IP Telephony platforms, offering advanced XML capability to access custom applications and support for up to 9 calls simultaneously. Part of the IPitomy family of IP telephones, the 53i is ideally suited for light to regular telephone requirements.

2011 Copyright  IPitomy Communication, LLC

219 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide IPitomy 53i IP Phone The 53i IP phone offers powerful features and flexibility in a standards based, carrier-grade basic level IP telephone. The 53i has a sleek and elegant design and 3 line LCD display, the 53i is fully interoperable with leading IP Telephony platforms, offering advanced XML capability to access custom applications and support for up to 9 calls simultaneously.

IPitomy 57i The 57i CT from IPitomy offers powerful features and flexibility in a standards based, carrier-grade advanced level, expandable, IP telephone that includes an integrated WDCT cordless mobility handset for coverage up to 300,000 sq ft.* With a sleek and elegant design, large 144 x 128 pixel graphical backlit LCD display and 6 dynamic context-sensitive softkeys, the 57i CT base unit is fully interoperable with leading IP Telephony platforms, offering advanced XML capability to access custom applications and support for up to 9 calls simultaneously. Part of the IPitomy family of IP telephones, the 57i CT is ideally suited for executives, heavy telephone users who require more one touch feature keys and a large screen to take full advantage of XML based programs and mobile warehouse, support and retail staff.

6739i The new 6739i, a new member of 67xi SIP portfolio, brings leading edge communications technology to the desktop in a stylish design. This phone features a giant touch screen display, Bluetooth, 1 GB Ethernet and enhanced audio components which make G.711 sound almost as good as Hi-Q our G.722 codec. This product is available in December 2009.

IP120 The IP120 is a value priced SIP based IP Telephone/Speakerphone. It has two Ethernet ports, supports Power over Ethernet and has a two line display. The IP120 supports two calls and has 5 programmable buttons. The IP120 is designed for applications where a low cost instrument is required such as kitchen, breakroom, warehouse, exam room or anywhere that does not require a large screen or more lines. The IP120 uses IPitomy's advanced Auto Provisioning features for easy deployment.

2011 Copyright  IPitomy Communication, LLC

220 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide IP51i The 55i from IPitomy offers powerful features and flexibility in a standards based, carrier-grade advanced level expandable IP telephone. With a sleek and elegant design, 144 x 75 pixel backlit LCD display and 6 dynamic context-sensitive softkeys, the 55i is fully interoperable with leading IP Telephony platforms, offering advanced XML capability to access custom applications and support for up to 9 calls simultaneously. Part of the IPitomy family of IP telephones, the 55i is ideally suited for moderate to heavy telephone users who require more one touch feature keys and XML based programs.

IPitomy 536M The 536M expansion module is designed to increase the power and flexibility of the 5i Series SIP telephones. Up to three modules can be used with the 55i, 57i or 57i CT telephone to create a powerful, feature rich console option. The 536M shares power and signaling with the phone, eliminating the need for additional wiring. Designed for receptionists, administrative assistants call center agents, power users, and executives who need to monitor and manage a large volume of calls on a regular basis, the 5i Series Expansion Modules provide an intelligent choice for all Enterprise IP environments.

IPitomy 560M The 560M expansion module is designed to increase the power and flexibility of the 5i Series SIP telephones. Up to three modules can be used with the 57i or 57i CT telephone to create a powerful, feature rich console option. The 560M shares power and signaling with the phone, eliminating the need for additional wiring. Designed for receptionists, administrative assistants call center agents, power users, and executives who need to monitor and manage a large volume of calls on a regular basis, the 5i Series Expansion Modules provide an intelligent choice for all Enterprise IP environments.

Detailed information regarding these phones including technical specifications can be found at www.aastra.com.

2011 Copyright  IPitomy Communication, LLC

221 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

APPENDIX 3: SOFTPHONES CounterPath™ eyeBeam® 1.5 and X-Lite® 3.0 What is a Softphone? CounterPath’s eyeBeam® 1.5 and X-Lite® 3.0 are Web-based telephones that operate from a PC. These nextgeneration Voice Over IP (VoIP) telephony client’s are designed to enhance a user’s communication experience by keeping them connected to callers anyplace and anytime through the convenience of an intuitive and userfriendly desktop. Based on open standards, CounterPath™ Softphones use a telephone-centric interface that allows users to manage voice, video, instant messaging (IM) and presence applications on their desktop. This comprehensive suite of carrier-grade solutions, give users the flexibility to meet the fast-paced and changing demands of any business.

X-Lite® 3.0 Free Softphone •

Intuitive user interface makes it easy for both novice and power users to make and receive calls, initiate video conferencing, and communicate using Instant Messaging.



Comprehensive Personal Address Book, including detailed calls lists and history.



Microsoft Outlook® integration allowing users to import their address book into their eyeBeam® contact list.



Zero-Touch Configuration of audio or video devices.



Instant messaging (IM) and presence management.



Multi-party and ad-hoc voice and video conferencing (IP and PSTN).



Voice and video call recording.



Pop-up management of incoming calls.

eyeBeam® 1.5 (Pricing available at www.counterpath.com) •

Intuitive user interface that makes it easy for both novice and power users to make and receive calls, initiate video conferencing, and communicate using Instant Messaging.



Comprehensive Personal Address Book, including detailed calls lists and history.



Microsoft® Outlook® integration allowing users to import an address book into the eyeBeam® contact list and dial directly from the application.



Zero-Touch Configuration of audio or video devices.



Instant messaging (IM) and presence management.



Multi-party and ad-hoc voice and video conferencing (IP and PSTN).



Voice and video call recording.



Pop-up management of incoming calls.



Security offering signaling and media encryption via TLS and SRTP streams.



Performance management of the SIP end-point (Softphone).



High compression CODEC support.

2011 Copyright  IPitomy Communication, LLC

222 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide Softphone Installation STEPS: 1

Using the Internet Explorer, go to the CounterPath website at the www.counterpath.com.

2

Download the CounterPath™ Softphone to be used with the system. The installation utility will install a phone icon in the toolbar of the operating system. It looks like a green light.

3

Left click the Softphone Icon in the operating system toolbar. The Softphone will appear.

4

Right click on the Softphone and select SIP Account Settings from the drop-down menu.

5

Click Properties. The properties window for the Softphone will appear.

6

Enter a Display Name. This is the name of the person or department associated with the phone.

7

Create a User Name. This is the extension the phone will be off of the IPitomy IP PBX. Be sure to use a number that is not being used by an existing extension.

8

Enter a Password. This password will need to be the same as the one used in the IPitomy IP PBX Extension Setup (Add New) page.

9

Enter the Extension Number in the Authorization User Name field.

10 Enter the Domain (IP Address) of the system to which the Softphone is to be connected. 11 Click Apply then select OK. Softphone Account Settings page will close. 12 Log into the IPitomy IP PBX (if not already logged in). Click Destinations and Extensions in the navigation bar of the system’s administration menu. The Extensions page will appear. 13 Click Add New. The Edit Extensions page will appear. Note that each new extension added automatically has a voice mailbox created. 14 Insert the Name or department associated with the extension being created. 15 Create an Extension Number for this person or department. 16 Populate the Email address for the person or extension. This will allow the system to forward email messages to the address of the person at the extension. 17 Select a status from the drop-down menu. An extension can be: •

Active – Currently in use.



Disabled – Not currently in use.

18 Create a voicemail PIN for the extension. PIN numbers must be between 3 and 4 characters long. The default setting is for the PIN to be the extension number. Be sure to instruct users to change the PIN to avoid unauthorized use. 19 Enter a Ring Time. This is the time in seconds that a call will ring before it is considered unanswered. Ring time must be between 1 and 360 seconds in length. 20 Define a Call Limit. This is the number of concurrent calls allowable at an extension. The Call Limit selected must be between 0 and 9. This limit will depend on the phone being installed.

2011 Copyright  IPitomy Communication, LLC

223 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide 21 Create a Call Group number. This number assigns this extension to a group with a similar purpose (e.g., Sales or Customer Service). Multiple call groups can be assigned to each extension by putting a comma between the group numbers. The call groups also define which Pickup Groups can answer calls to this extension. 22 Create a Pickup Group. This number must match the Call Group number(s). It defines the Call Group Numbers this extension can pickup remotely by pressing *8. 23 Click Apply Schedule. When an extension is created, a schedule destination is created. This schedule is not activated until the Apply Schedule box is selected. When it is selected, you can setup a schedule for this extension by selecting Schedule under the Destinations Menu and clicking on the schedule for that extension. Extension schedules will appear with the name of the extension (e.g., Extension 123 would appear as “ext_123”). See the Schedules section of this guide for more information.

Forward Settings The forwarding settings are made to be very user friendly. The settings may be modified from the Smart Personal Console, changed from your telephone extension or changed remotely from any telephone (including cell phones) using the touch-tone key pad of any telephone. Forward settings routes calls to a different destination. These settings can be: •

Unconditional – Always route calls to a specific destination.



Busy – Route calls to a specific destination when the extension is in use or do not disturb is selected.



No Answer – Route calls to a specific destination when a call is not answered.



Unavailable – Route calls to a specific destination when a phone is turned off, is not registered with the system or has reached its call limit (as set In the IP PBX).

Provisioning Forward Settings

STEPS: 1

Pick the setting to be provisioned – Unconditional, Busy, No Answer or Unavailable.

2

Select Enabled or Disabled. Disabled turns the forward setting off. Enabled turns the forward setting on.

3

If the Forward setting is Enabled, you can choose to select a destination from the dropdown list. The IPitomy IP PBX allows calls to be forwarded to a PSTN. Forward calls to a PSTN number by entering it into the field provided. Calls can be forwarded to any destination (or telephone number) in the drop-down list or any telephone number.

Changing a Forwarding Number from an Extension Only unconditional forwarding can be changed from a touch-tone keypad. •

Dial *90 to disable forwarding.



Dial *91 to enable forwarding.



Dial *92 to set the forwarding number.

2011 Copyright  IPitomy Communication, LLC

224 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

Changing a Forwarding Number from a PC

STEPS: 1

Browse to the Smart Personal Console page.

2

Login.

3

Select a Destination for the chosen forward type.

4

Enter the telephone number.

Changing a Forwarding Number While Away from an Extension Only unconditional forwarding can be changed from a touch-tone keypad. When it is necessary to modify the forwarding setting while away from the office, the IPitomy IP PBX has a forwarding application built into the system. It is necessary to have an automated attendant menu accessible from outside the system. The forwarding gateway is selectable as an option from the Smart Personal Console. When away from the office, it is possible to call into the Automated Attendant, enter the digit setup to be the forwarding gateway. Here users can turn forwarding on or off and enter a different number to forward calls to.

STEPS: 1

Call into the Automated Attendant menu.

2

Select the touch-tone digit that has been set for modifying forwarding settings.

3

The system will prompt for an Extension Number and Password.

4

The system will indicate if extension forwarding is Enabled or Disabled.

5

Pressing “1” toggles between Enabled and Disabled.

6

Pressing “2” allows the forwarding destination to be modified.

Advanced Settings Network Settings When installing a Softphone change the SIP Password in Network Settings to match the password created in the Softphone Account Settings. The rest of these settings represent service provider permissions and identification information. These other system (extension) defaults should not be changed.

2011 Copyright  IPitomy Communication, LLC

225 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

APPENDIX 4: IP ADDRESSES Determining Local Network Address (on a Microsoft Windows Machine) To determine the local network address on a Microsoft Windows machine:

STEPS: 1

Go to Start and click on Run. Type “cmd” and press Enter.

2

At the Command Prompt type “ipconfig /all” and press Enter. Windows will display the current connection details (Diagram 63). These connection details contain important information used in the setup of the IPitomy IP PBX.

3

Write the following information in the IPitomy IP PBX Installation Checklist: • • •

IP Address Subnet Mask Default Gateway

Determining an Available IP Address Adding the IPitomy IP PBX to an existing Local Area Network (LAN) requires knowing what IP address can be given to the system. Every new piece of equipment added to the network must have its own IP address. Pinging an IP address determines if an IP address is available to be used. A ping is a call to the IP address to see if it exists. If a ping gets a response then the IP address is in use. To ping an IP address on a Windows-based machine already configured on the local network:

STEPS: 1

Go to Start and click on Run. Type “cmd” and press Enter.

2

At the Command Prompt type “ping *[192.168.1.249]” and press Enter. This IP Address is the IPitomy IP PBX default static IP Address. The IP Addresses you ping on your local network will be defined by your router. For example, even though the default IP Address for the IPitomy IP PBX is 192.168.1.249, the IP Addresses that you ping to determine if one is available may differ. This will be determined by your gateway (router) address.

3

If you receive a “Destination net unreachable” message like in the number *[192.168.1.249] is an IP Address not in use and can be assigned to the IPitomy IP PBX. NOTE: Sample configurations are for a Windows XP  operating system and Linksys router and are for demonstration purposes only. This IP Address is determined by the default gateway (router) you discovered in Determining the Local Network Address.

4

If you get a return or “Reply from *192.168.1.249”, the IP Address is in use. Continue pinging IP addresses on “*[192.168.1.XXX]” that are greater than “*[192.168.1.249]” until you find a “Destination net unreachable.” Make a record of this IP address in the IPitomy IP PBX Installation Checklist to use later in the installation.

2011 Copyright  IPitomy Communication, LLC

226 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

APPENDIX 5: DHCP SETTINGS Internet Protocol (IP) addresses are used to facilitate communication between equipment within a network. Each piece of equipment on a network has a unique IP address. These addresses are maintained in a list on a server (a computer that manages information traffic throughout a network). The list has both static (non-changing) and dynamic (varying) IP addresses. Those that are static do not change and can be used by Web servers that require a permanent connection to the Internet. Those that are dynamic are assigned as needed to allow communication between equipment or servers on the network. Dynamic Host Configuration Protocol (DHCP) lets Network Administrators manage an organization’s network centrally and automate the assignment of IP addresses using the internet protocol TCP/IP. DHCP supports the management of IP addresses and internet traffic by: Automatically assigning an IP address to a computer if it moves to another location on the network. If DHCP didn't exist the new IP address would have to be manually configured. Allowing a Network Administrator to supervise and distribute IP addresses from a central point automatically sending a new IP address when a computer is plugged into a different place in the network.

Leasing Time for an IP Address DHCP uses the concept of a “lease” or an amount of time that a given IP address will be valid for a computer. The lease time can vary depending on how long a user is likely to require the Internet connection at a particular location. DHCP is especially useful in education and other environments where network users change frequently. In these settings, by using very short leases, DHCP can dynamically reconfigure networks in which there are more computers than there are available IP addresses.

Determining/Viewing DHCP Settings on a Linksys Router STEPS: 1

Log into the router using the router’s IP address (e.g., 192.168.1.1).

2

Enter a Username and Password at the Login page.

3

Click the Advanced Tab and DHCP.

Tips for Understanding the IP Address List Listed below are some tips that explain the DHCP Settings: •

The starting IP address determines the first IP that will be auto assigned by the router (e.g., 192.168.1.100).



The number of DHCP users determines the amount of auto assigned IP addresses that can be generated (e.g., 50).



In a scenario with 50 users, "192.168.1.49" would be the last auto assigned IP address in the pool.



To set an IP address outside the DHCP pool, statically assign the system to a number beyond the pool (e.g., 192.168.1.249).

2011 Copyright  IPitomy Communication, LLC

227 www.ipitomy.com

v4.0.1

IPitomy IP PBX Admin Guide

APPENDIX 6: ROUTER CONFIGURATION The sample setup instructions below use a Linksys router and are meant for demonstration purposes only.

STEPS: 1

Log into the router using the router’s IP address (e.g., 192.168.1.1).

2

Open a Web browser. Enter the IP address of the router (e.g., 192.168.1.1) and press Enter.

3

Login to the router using the Username and Password. For help refer to router documentation.

4

Navigate to Port Forwarding. For help refer to router documentation. Open ports 5060 to 5060 on the IP address for the system being installed (e.g., 192.168.1.249) for both UDP and TCP (Name = SIP).

5

Open ports 10000 to 20000 on the IP address for the system being installed for both UDP and TCP (Name = RTP).

6

Open ports 4569 to 4569 on the IP address for the system being installed for both UDP and TCP (Name = IAX2).

7

Click Apply Changes to commit the changes to the database.

APPENDIX 7: NETWORK CONSOLE The system comes with an application that allows the IP Address and other network attributes to be changed to meet the requirements of the specific network. Using the Network Console allows you to view and change settings without requiring an external web browser.

Accessing the Network Console STEPS: 1

Verify that the IP1500 is powered and that a keyboard and monitor are connected directly to it.

2

If the monitor screen is blank go to step 4. However, if you see the Network Console, go to step 5.

3

If you just powered up the IP1500, you will see various system housekeeping messages scrolling on the screen. Do not press any keys at this time. Soon the messages will stop moving and be replaced with a “login as” prompt.

4

Press CTRL + ALT + F7, simultaneously. If nothing happens, go to step 1.

5

View or make changes as needed.

Selecting Options Options are single letters or digits within brackets. You select an option by typing the option letter/digit and then pressing the Enter key. For example, on the Main menu, [1] indicates you can select the Network Type by typing 1 and pressing Enter. A blank option [ ] indicates that you cannot edit the value in the current context.

IPitomy IP PBX Admin Guide

Menus •

Each menu screen contains 4 sections:



Menu Location.



“Using” (Live) System Settings.



Database Settings.



Commands.

Menu Location The location “bar” tells you where in the configuration system you are. For example, the Main Menu is “IPitomy Networking – TCP/IP Settings”. Another menu is “IPitomy Networking – TCP/IP Settings – Subnet Mask”

Using the “Live” System Settings This section always contains the current network system information.

Database Settings Most values in this section are IP Addresses. The values can be edited. To edit a value you first select the corresponding option. Options here are always numbered. Edits do not modify actual network settings until you “Save & Update”.

Command Options To issue a command select the desired option. Which options are available vary depending on where you are within the menu system. Some important options are:

Refresh View [R] •

When to use:



Undo edits you do not wish to save.



See the latest live network information.



See if the database has been modified by someone else.

Default Settings [D] Changes the values listed in the menu to factory defaults. Remember, you must save your changes to actually update your network interface.

Save & Update [S] Save settings and update network connections.

Disable [Z] IP address values can be disabled with this option.

IPitomy IP PBX Admin Guide

Network Type DHCP DHCP may be used to simplify networking administrative tasks such as initial system configuration. With Network Type set to DHCP, several IP Address options become unavailable. For more information about DHCP and IP1500 networking requirements, refer to the appropriate section of this manual. Acquiring a DHCP Lease

STEPS: 1

Change Network Type to “DHCP”.

2

Save & Update.

Renewing DHCP Lease

STEPS: 1

Verify Network Type is set to “DHCP”.

2

Save & Update.

Other Menus •

[W] Web Server



[H] Host Access



[F] Fix Database

Web Server This menu allows you to restart the Web Server, and modify which IPs and/or domains can access the web server. To apply changes you must restart the web server. This will not interrupt phone service. A reboot of the PBX will also apply changes made here. The “Allow” format may be: domain name, full IP address, partial IP address, network/netmask pair, network/nnn CIDR specification. Changes to the Web Server access list are database independent so custom changes do not migrate from one box to another via a database backup file.

Host Access Limit access to special services on the PBX. An “allow from” entry is a list of one or more host names, host addresses, patterns or wildcards that will be matched against the client host name or address. List elements should be separated by blanks and/or commas. Changes to the Host access list are installed immediately. They are database independent so custom changes do not migrate from one box to another via a database backup file. *Changes made to Web Server and Host Access settings are installed immediately. You must restart the Web Server ([U] option, or the PBX) before Web Server access changes are used by the Web Server. The Web Server and Host Access console menus provide all of the functionality of the System > Access Control web page.

IPitomy IP PBX Admin Guide

Fix Database From here you can factory default your database. This will permanently change your system. Be sure this is really what you want to do before proceeding.

Tips for Using the IPitomy IP PBX Network Console Always read the text near the cursor before pressing keys. Otherwise you could miss an important warning message. If the IP1500 console has been left unattended with the Network Console Menu present on the monitor screen, and you believe someone else may have modified network settings remotely since the last time the console was used, be sure to select Refresh Database View before making changes or using Save & Update. This ensures that you do not accidentally revert settings to an undesired prior state and that you are not relying on out of date information. While unlikely, it is possible for the actual database settings to be out of sync with the “Using” (live) network settings. If you want to switch the actual settings to the database values, simply select Save & Update. If you want to re-configure the network, edit the settings first. Then Save & Update.

IPitomy IP PBX Admin Guide

APPENDIX 8: SOFTWARE UPGRADE Checking for Upgrade Availability 1. Log into the PBX

2. Navigate to PBX Setup=>Services and note the firmware version. If the PBX firmware is earlier than 3.xxxxx then your system requires a Hard Drive upgrade before you will be able to load any 3.x firmware onto the system. Please contact your IPitomy Sales Representative if an HD upgrade is needed; otherwise continue with the steps laid out in this guide.

System Backup 1. Go to PBX Setup=>Database 2. Click Backup to create a backup of the current database 3. Find the most recent backup and click the Down action arrow to download this database to your computer

Downloading the Firmware File 1. In a web browser, navigate to http://www.ipitomy.com/pbx_files/ip1500/ 2. Download the Current Release

IPitomy IP PBX Admin Guide Loading the Firmware File 1. Log into the PBX and navigate to PBX Setup=>Services

2. Scroll down to the File System panel 3. Click Browse and find the current firmware file ipitomy_pbx_-uf.tgz 4. Click Load File to begin the upgrade process 5. Depending on your starting firmware version, one of two things will occur: 1. A dialog box will pop up announcing that the PBX will reboot, click OK and wait 5 minutes. After the 5 minutes has passed, log out of the PBX, then log back into the PBX (you should see a message when logging in that the Database does not match and will be converted) 2. A progress bar will appear while the PBX upgrades and reboots, after which you will be returned to the login screen. 6. Log into the PBX and a message will display stating the Database version does not match. Click OK and the DB will update. 7. Click Apply Changes

Restoring Backups (Does not need to be done if you want to use the same DB as was previously running on the system) 1. Navigate to PBX Setup=>Database 2. Find the backup you wish to load and click the curved arrow to restore it as the active database. 3. Once the Database loads, Click Apply Changes. 3. Navigate to PBXSetup->Services and Click "Restart All Services"

For systems with Digium© Analog Cards/T1/PRI Cards or Xorcom© USB Devices 1. If your system has any of these products installed, navigate to Providers=>Hardware Providers

IPitomy IP PBX Admin Guide 2. Scroll down to the Hardware Functions panel 3. Click Restart USB Devices & PBX Services

APPENDIX 9: TROUBLESHOOTING (FAQ) (Q) Why does my Aastra phone freeze with 100% done written on the screen? (A) The phone is attempting to access an unreachable network. You need to manually change the TFTP server IP on the phone to match the PBX IP. Also make sure that PBX Network Settings IP matches your actual PBX IP. If it does not, change it and SAVE the change. Make sure that the PBX Sip IP has been properly set:

STEPS: 1

Change the setting in PBX Setup / SIP.

2

Click on “Apply Changes” button to commit the changes to the database

3

Restart the phone.

(Q) Why did my phone restart with an old configuration after using Auto Discovery to create a new extension, assign and restart the phone? (A) When you create a new extension you are taken to the Create Extensions page. After you click on the "Create" button you must then click on "Apply Changes" before restarting the affected phones.

(Q) Why does my Aastra phone hang (or freeze) with "40% Done" written on the screen? (A) This is a known issue with the Aastra 480i model that sometimes occurs after Factory Defaulting the phone. You need to turn the phone off and turn it back on. Remove the power connection, wait a few seconds and then re-connect the power.

(Q) Why won’t my time zone on my voicemail change after my system settings have been changed? (A) You have to go to PBX>Services and click on the Restart PBX button in order for the changes to take effect.

(Q) Why can’t I delete a menu? (A) Be sure the menu is not being used in incoming routing.

(Q) What is the default IP Address for the IP PBX? (A) The IP Address for the PBX is 192.168.1.249

For the most recent troubleshooting FAQ’s please visit www.ipitomy.com

IPitomy IP PBX Admin Guide

GLOSSARY The following terminologies relate to either standard Internet Protocol (IP) and/or IPitomy’s suite of products.

A Analogue Telephone Adapter (ATA) – Connects a telephone to a high-speed modem and facilitates VoIP or fax calls over the internet.

Automatic Call Distribution (ACD) - The IPitomy’s ACD product is an IP-based component that allows management of calls and features Virtual Call Centers, Skills-based Routing, Multiple Queue Assignments and Overflow/Load Balancing.

B Backbone – Global network connections that route voice and data traffic from one major metropolitan area to another.

Bandwidth – The transmission capacity of a given device or network. Broadband – An internet connection that is always-on and fast. Browser – A software application that allows users to view and navigate to information on the Web. Microsoft® Explorer® and Mozilla Firefox® are two common browsers.

Busy Lamp Field (BLF) –This is an LED on a phone that designates the status or another phone or feature in the PBX.

C Caller ID – Displays the name and telephone number of a person calling. Call Detail Record (CDR) – Information about calls collected from the IPitomy IP PBX for a specified period of time. This report is downloadable. The report details the numbers of calls, call duration, call origination and call destination. Class of Service (CoS) – Class of Service defines which outbound routes a particular extension or feature has access to for outbound dialing. Cloud Computing - refers to applications and services offered over the Internet. These services are offered from data centers all over the world, which collectively are referred to as the "cloud." This metaphor represents the intangible, yet universal nature of the Internet. CODEC (Compression-Decompression) – Defines the algorithm used to compress and decompress audio, video, etc. The IPitomy PBX has many codecs to choose from.

D Digital Subscriber Line (DSL) – This service provides digital phone service over an analog line. Direct Inward Dial (DID) – When a trunk has multiple lines, you can use a DID to route calls in the PBX to specific destination.

Domain Name Server (DNS) – These are servers on the public internet which resolve the domain name into an IP address. Without a valid DNS server, many of the services used by the PBX (Time, Email, etc) will not be accessible if they use a domain name.

Do Not Disturb – Prevents notification of incoming calls.

IPitomy IP PBX Admin Guide DTMF (Dual-tone Multi-frequency) – This is the touch-tone or audio signal a phone sends to a phone system to get it to perform some action.

Dynamic IP– An IP address that changes and is not static. Dynamic Host Configuration Protocol (DHCP) - This is a computer networking protocol used by hosts (DHCP clients) to retrieve IP address assignments and other configuration information.

E Encryption – The process of scrambling data to prevent the accurate interpretation of this data by anyone except those for whom it is intended.

Ethernet - a family of frame-based computer networking technologies for local area networks (LANs).

F Firewall - A firewall is a part of a computer system or network that is designed to block unauthorized access while permitting authorized communications. It is a device or set of devices which is configured to permit or deny computer based application upon a set of rules and other criteria.

Forward – the action of automatically configuring a call that was intended for one party to go to another destination.

G Gateway – A device that interconnects networks with different, incompatible communications protocols.

H I Institute of Electrical and Electronics Engineers (IEEE) – An independent institute that develops networking standards.

Infrastructure – Currently installed computing and networking equipment. IP Telephony – Phone service (voice calls) carried over a network using Session Initiation Protocol. Interactive Voice Response (IVR) - IVR is a telephony technology that can read a combination of touch tone and voice input. It gives users the ability to access a database of information via phone. A typical IVR system has several menus of prerecorded options that the caller can choose from. While many choices are as basic as choosing a number, some options may require the caller to speak detailed information such as his name or account number. This input is read by the IVR system and is used to access the appropriate information in the database.

IPitomy IP PBX Admin Guide Internet Protocol (IP) – A protocol used to send data over a network. These are currently set to IPv4 meaning 4 octets ranging from 0-255. The public internet takes up a majority of these addresses, but there are certain ranges reserved for private LANs.

Reserved Private IP Address Ranges Start

End

Number of Addresses

24-bit Block (/8 prefix, 1 × A)

10.0.0.0

10.255.255.255

16,777,216

20-bit Block (/12 prefix, 16 × B)

172.16.0.0

172.31.255.255

1,045,576

16-bit Block (/16 prefix, 256 × C)

192.168.0.0

192.168.255.255

65,536

Internet Service Provider (ISP) – A company that provides access to the Internet.

J Jitter - This is the deviation in or displacement of some aspect of the pulses in a high-frequency digital signal. As the name suggests, jitter can be thought of as shaky pulses. The deviation can be in terms of amplitude, phase timing, or the width of the signal pulse.

K L Local Area Network (LAN) – A group of computers and other devices that share a common communications line. These devices most often share a server and are located within a small geographic area. Loop Back - The term loopback is generally used to describe methods or procedures of routing electronic signals, digital data streams, or other flows of items, from their originating facility quickly back to the same source entity without intentional processing or modification. This is not something you want to do on a LAN.

M MAC Address - A Media Access Control address (MAC address) is a unique identifier assigned to network interfaces for communications on the physical network. http://en.wikipedia.org/wiki/MAC_address

Message Waiting Light – A light on a phone indicating that a voicemail message is waiting. Music on Hold – Music or announcements callers listen to while on hold.

N Network – A group of computers or devices that share a common communication line and are typically used for the transmission of data and voice traffic.

Network Address Translation (NAT) – Network address translation converts your LAN IP to the Public IP, allowing traffic to go out to the internet and route back to the correct device on your LAN. http://en.wikipedia.org/wiki/Network_address_translation

IPitomy IP PBX Admin Guide

O Original Equipment Manufacturer (OEM) - This refers to a company that produces hardware to be marketed under another company's brand name.

P Packet – A unit of data transmitted over a network. This is a small amount of computer data sent over a network. Any time you receive data from the Internet, it comes to your computer in the form of many little packets. Each packet contains the address of its origin and destination, and information that connects it to the related packets being sent. Park – Parks a call in a reserved extension (park slot) and allows the call to be retrieved from another extension. POE (Power over Ethernet) – A method of providing power to a network device over the network cabling, eliminating the need for a power supply.

Port – Ports can describe two different devices. An Internet port. This is a number that indicates what kind of protocol a server on the Internet is using. For example, Web servers typically are listed on port 80. Web browsers use this port by default when accessing Web pages A hardware port. This refers to any one of the ports that are on the back of a computer where devices can be hooked up (like a keyboard, mouse, printer, etc). Some common ports found on today's computers are USB, Firewire, and Ethernet.

PRI (Primary Rate Interface) – ISDN service provides 23 64-Kbps B (Bearer) channels and one 64-Kbps D (Data) channel (23 B and D). The D Channel is used for control in signaling information.

Private Branch Exchange (PBX) – An in-house telephone system that connects extensions and the Public Switched Telephone Network.

Public Switched Telephone Network (PSTN) – This is the global circuit-switched telephone network. It is similar to the Internet. However, on the Internet packets of data are sent and received using Internet protocol over a network.

Q Quality of Service (QoS) - The ability to provide different priority to different applications, users, or data flows, or to guarantee a certain level of performance to a data flow.

R Redundant Array of Independent Disks (RAID) – This is a method of storing data on multiple hard disks. When disks are arranged in a RAID configuration, the computer sees them all as one large disk. However, they operate much more efficiently than a single hard drive. Since the data is spread out over multiple disks, the reading and writing operations can take place on multiple disks at once. This can speed up hard drive access time significantly. Multiple hard drives may not improve hard disk performance as much as multiple processors may enhance the CPU performance, but it is based on a similar logic.

Real-Time Protocol (RTP) - a standardized packet format for delivering audio and video over IP networks. Router – A networking device that connects multiple networks together, such as a local network and the Internet.

S Server – Any computer in a network that provides users access to files, printing, communications, etc. Server Time – this is the time set on the server where the phone or device is located. The server time for

IPitomy IP PBX Admin Guide IPitomy’s IP PBX system is synched to time.nist.gov server time.

Session Initiation Protocol (SIP) – A signaling protocol that establishes data sessions. For example when making a call from one extension to another on a VoIP phone system SIP sets up the call and creates the connection between the two extensions.

Smart Personal Console (SPC) – This user-friendly Web page gives a person the ability to set basic phone features (mailbox settings, phone key settings, call forwarding, etc) from anywhere. Additionally, the user can check their voicemail and call logs from the SPC. Stateful Packet Inspection (SPI) – A stateful inspection is a firewall architecture that works at the network layer. Unlike static packet filtering, which examines a packet based on the information in its header, a stateful inspection tracks each connection traversing all interfaces of the firewall and makes sure they are valid. Static IP – an IP address that does not change. Subnet Mask – A subnet mask is a number that defines a range of IP Addresses that can be used in a network. Subnet masks are used to designate subnetworks, or subnets, which are typically local networks LANs that are connected to the Internet. Systems within the same subnet can communicate directly with each other, while systems on different subnets must communicate through a router. Therefore, subnetworks can be used to partition multiple networks and limit the traffic between them. Switch – A network device that connects network segments. These come in POE and non-POE varieties.

T T1 – A dedicated digital voice circuit that has 24 channels. This point-to-point circuit delivers 1.544 Mbps of bandwidth. TFTP (Trivial File Transfer Protocol) – a simple protocol to transfer files. IPitomy uses this method in regards to phone firmware and configuration files. http://en.wikipedia.org/wiki/Trivial_File_Transfer_Protocol

Time to Live (TTL) – This refers to an aspect of the Internet Protocol. TTL is used when a "ping," or a request for a response, is sent to another computer, such as a server. The TTL represents the number of hops, or servers in different locations, the request can travel to before returning a failed attempt message.

Transfer – Sends a call to another extension. Trunk – A communications channel between two points. Transmission Control Protocol (TCP) – Packets sent via this method are verified end to end.

U Upload - While downloading is receiving a file from another computer, uploading is the exact opposite. It is sending a file from your computer to another system. It is possible to upload and download at the same time, but it may cause slower transfer speeds, especially if you have a low bandwidth connection. Because most files are located on Internet servers, people generally do a lot more downloading than uploading.

Uniform Resource Locator (URL) - A URL is the address of a specific Web site or file on the Internet. It cannot have spaces or certain other characters and uses forward slashes to denote different directories. Some examples of URLs are http://www.cnet.com/, http://web.mit.edu/, and ftp://info.apple.com/.

Uninterruptible Power Supply (UPS) – A devise that maintains continual electrical power. User Datagram Protocol (UDP) - Packets sent via this method are fire and forget.

V Virtual Private Network (VPN) – a computer network that uses a public telecommunication infrastructure,

IPitomy IP PBX Admin Guide such as the Internet, to provide remote offices or individual users with secure access to their organization's network.

Voice Over Internet Protocol (VoIP) – The routing of voice traffic over the internet. VoIP is basically a telephone connection over the Internet. The data is sent digitally, using the Internet Protocol (IP) instead of analog telephone lines.

W Wide Area Network (WAN) – A computer network that crosses geographic boundaries like cities, states or countries.

Wireless Local Area Network (WLAN) – A link between two or more computers in a network without wires. Wireless LANs use radio waves to communicate between computers in a limited area.

IPitomy IP PBX Admin Guide

Notes:

Loading...

IPitomy IP PBX Administrator Guide

IPitomy IP PBX Administrator Guide Version v4.0.1 IPitomy IP PBX Admin Guide All materials in this documentation are proprietary and considered con...

4MB Sizes 1 Downloads 13 Views

Recommend Documents

IP PBX, SIP & IAX - Vavai
tone yang dihasilkan (DTMF=dual-tone multi- frequency) akan dibawa oleh kabel ke perangkat berikutnya. Biasanya sinyal d

Dynamix IP PBX-100 User's Manual
Customers can select different suite and optional products to meet their request. To. Integrate with Dynamix DW can prov

FacetPhone IP-PBX System Quote - FacetCorp
You can fill out and submit the form below to get a preliminary quote on a FacetPhone system. We will email the quote to

Administrator Guide
Oct 28, 2013 - Disclaimer. Sagemcom reserves the right to make changes and alterations to its software and documentation

Orion NPM Administrator Guide
Exporting Reports as Excel and PDF from the Orion Web Console. 603. Exporting Reports from the Orion Report ...... Note:

3320DNI System Administrator Guide
Xerox Phaser 3320DN/3320DNI. System Administrator Guide. 16. 2. Press the arrow buttons to highlight Network Setup and p

IP Guide!
9 Internet Protocol (IP/IPv4, IPng/IPv6) and IP-Related Protocols (IP NAT, IPSec, Mobile IP) ... We must do this in bina

SpamTitan Administrator Guide
The graphical user interface (GUI) enables you to manage and monitor the system using a web-based interface. Each page i

Jual Murah IP PBX IP Phone VoIP Gateway GSM Jakarta Toko
Sedangkan PABX Konvensional harus memiliki buku manual yang tebal, untuk memrogram harus mempunyai pesawat telepon khusu

Administrator Quick Start Guide - Cengage
Cengage Learning's MindLinks provide seamless, powerful integration with Blackboard Partner Cloud and your institution's